-
Product
Photo Detector Testing
-
With the rise of 5G technology and popularization mobile devices, more and more advanced photoelectric sensors are used in our daily lives. In order to be better applied to mobile devices, the photosensitive area of these advanced photodetector is getting smaller and smaller. However, these applications place higher and higher requirements on the light sensing performance of advanced photodetectors. In the process of shrinking the photosensitive area, it also brings the challenge of accurate measurement of quantum efficiency. Enlitech adopts the spatial light homogenizing technology and follows the ASTM standard “Irradiance Mode” test method, which is proven that it can accurately perform quantum efficiency and other key parameter measurements of advanced photodetectors.
-
Product
3 In 1 Metal/Voltage/Stud Detectors With LCD
6361
-
Peaceful Thriving Enterprise Co Ltd
Detect the real position of voltage, metal and stud.
-
Product
Carbon Monoxide Detector Tester
Solo C3
-
Many multi-sensor fire detectors detect carbon monoxide (CO) as well as smoke and / or heat. Under international codes and standards the CO cell needs to be functionally tested with a CO stimulus from the protected area through the detector vents to the sensor.
-
Product
Ignition Pulse Detector
IP-292/296
-
These detectors are electromagnetic induction type detector designed to detect the number of ignition pulses produced in the gasoline engines. The IP-292 pinches a primary cord (low voltage) and the IP-296 pinches a secondary cord (high voltage) of the ignition coil. The compact, light-weight and clip-on design of these detectors offer a simple and easy detection of the number of pulse. Since the detector and its cord are made of heat resistance materials, these models are not affected by the high temperature in the engine room. These detectors are used with the engine tachometers made by Ono Sokki. (AR-7240B, CT-6700, HT-6200, SE-1620, FT-2500 or GE-2500)
-
Product
Detectors
-
Teledyne Microwave Solutions (TMS) offers all types of detectors with both analog & threshold designs operating from 10MHz to 26GHz, with excellent power temperature stability. With over 50 ITAR-Free designs, many packaging options and with up to 10nS pulse response, TMS are able to offer the right detector for your particular application.
-
-
Product
Quick Response Time Combustible Gas Leak Detector w/ Alarm
CD200
-
UEi Test & Measurement Instruments
The CD200 has a long, slim gooseneck probe and a bright LED tip light to find combustible gas leaks in tight areas. Its adjustable alarm, easy one-hand operation and impact resistant storage case add up to value and convenience.
-
Product
Infrared Gas Detector
GD10 Series
-
Teledyne Gas & Flame Detection
The GD10 Series has been designed with features that provide an effective response to the detection of gas hazards in a wide range of industrial environments from boiler plant rooms to offshore petrochemical installations.These infrared gas detectors differ from all other models, because they utilize silicon based solid-state infrared sources. The complete optomechanical design and construction is so stable that an ultra fast speed of response can be achieved while providing unparalleled service life and detector stability, thus saving on maintenance and service costs.We offer the longest combined detector and IR source warranty on the market.
-
Product
Magnetic Particle Flaw Detector
MT-1C
-
MT-1C magnetic particle flaw detector adopts high-capacity lithium battery pack, can convert DC to AC through variable-frequency, provide magnetic powder flaw detector with magnetic power supply. With low power consumption, it can continuous work for more than four hours after charging. It is especially proper for working in the wild and aerial area.
-
Product
SWIR Camera with InGaAs Detector
FLIR A6260
-
The FLIR A6260 SWIR camera offers superior sensitivity and dynamic range paired with the flexibility of customized windowing and integration times. This InGaAs camera is very linear in the 0.9 to 1.7 µm sensing waveband, making it the perfect tool for high temperature thermal measurements and applications that require measuring through standard glass. The A6260 offers control over settings such as integration time, while allowing you to synchronize and trigger to external events and devices.
-
Product
Photoelectric Detector
LG-930
-
The LG-900 series detectors are reflection type optical (LG-916) and photoelectric detectors developed for medium distance detection applications. The LG-916 adopts glass fiber at the tip end and can be protective enough against the external turbulent light because of pulse modulation system as the light projection source. The LG-930 also uses a pulse-lighting method, it is practically unaffected by disturbance light, furthermore, featuring a hybrid structure with the all light-projecting, light-receiving, amplifying, and waveform-shaping sections built into the unit to offer a compact design with easy-to-operate functions. By simply attaching the reflection mark to a rotating object, the detectors can detect the rotation of the object without actually touching the object.
-
Product
Beam Position Detectors
-
We offer a wide range of laser beam position detectors for optical alignment including Quadrant Cell Photoreceivers, PSDs, and Thermopile Position Sensors. Please see our Beam Position Sensor Guide for more information.
-
Product
Burst Detectors
-
The Burst detector monitors interference threshold exceedances at cable-and line bundles. It selectively detects conducted disturbances, which would influence the monitored device.
-
Product
Modular Linear Detector Arrays
X-Scan M
-
X-Scan M series makes quick and accurate inspection of large-scale objects easy. The modular linear detector arrays are scalable to different inspection system lengths up to 4.1 meters with one controller and single Gigabit Ethernet interface. With network connected units even longer scanners can be built efficiently for high-energy applications.
-
Product
Detector And FPA Testing
-
The FPA Test Set (FPATS) interface to the detectors under test (DUT’s) is via a custom pedestal plate which provides both a conductive heat path to both the individual DUT’s as well as the field of view limiting aperture plate. This custom pedestal plate protrudes through the customer provided DUT interface printed circuit board (PCB) and makes physical contact with the rear of the DUT packages and the aperture plate when the FPATS is in the closed position. The pedestal plate is mounted to the ambient source plate and its temperature is actively driven by this subsystem.
-
Product
Motor/Gasoline Engine RPM Detector
OM-1500/1200
-
The OM-1500/1200 motor/gasoline engine RPM detector is designed for rotation measurement of a gasoline engine and an EV/HEV motor. It detects magnetic flux leakage from the motor itself or the engine’s ignition coil.This easy to use and durable detector can measure engine rotation by attaching in parallel with the ignition coil. When the EV/HEV motor rotation is measured, attach the OM-1500/1200 perpendicular to the motor rotating shaft.It is used with the engine tachometer by Ono Sokki (GE-2500, AR-7240B, CT-6520B, HT-6200, SE-1620, FT-2500, FT-7200).
-
Product
Single Photon Detector System For Near-Infrared (1.6-2.3 Um Wavelength) Waves With Closed-Cyle Cooling
-
Single Photon Detector System for Near-Infrared (1.6-2.3 um wavelength) waves with Closed-Cylce (cryogen-free)cooling
-
Product
Log Detector, SMA, Positive Video Out, 10 MHz to 3 GHz
PE8040
-
Pasternack log detector PE8040 is part of our extensive in-stock RF, microwave and millimeter wave components available for purchase. This log detector is manufactured with SMA female to SMA female connectors. Our SMA log detector has a minimum frequency of 10 MHz and a maximum frequency of 3 GHz.
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
High-Power Detector Laser Power Meters
11PMK-W5
-
11PMK-W5 power detectors surface absorber stands up to average power densities of 100 kW/cm². That is the best in the world for average power density. 11PMK-W5 high-power detectors come ready to mount on a rod, a bracket and the square case even lets you set them right on the optical table.
-
Product
Phantom Pipeline Metal Detector
-
The Phantom IP69K certified Stainless Steel Pipeline system detects metal contamination in pumped liquids and pastes conveyed through its non-metallic pipe. The extra-rugged BSH casing enables the system to withstand the harshest production environments. Pipe material options include nylon, rubber, and Teflon wrapped pipe for higher pressure / temperature applications. The Diverter Valve reject system is typically used to divert contaminated product from the flow. A test ball insertion/retrieval kit is offered as an option with Pipeline systems, allowing for ease of manual testing.
-
Product
Tunnel Diode Zero Bias Detectors
-
A tunnel diode zero-bias detector is a device that converts microwave and millimeter-wave radio frequency (RF) signals into a DC voltage without requiring an external power source
-
Product
SmartWireless Gas Detector
CXT
-
Teledyne Gas & Flame Detection
All component parts are rated for Class 1; Division 1, Group C, D hazardous areas. These advanced field devices consist of a CXT low power gas detection sensor and wireless transceiver packaged in a single enclosure. Power is provided by a disposable “C” cell battery pack capable of continuous operation for greater than 60 days. Additional power options include a Smart Rechargeble battery with a run time of 5-6 months, a disposable “D” cell battery pack with a run time of 9 months and solar panel providing continuous operation.
-
Product
Hazardous Area Gas Detector
Meridian
-
Teledyne Gas & Flame Detection
Whether you need an infrared or catalytic bead sensor to detect combustible gases or an electrochemical sensor for a toxic environment, the Meridian universal gas detector utilizes a single detector head to easily accept all sensor types. There is no requirement for distinct personality boards in the gas detector or different detector heads to make the instrument behave as a combustible or toxic gas detector. The Meridian gas detector accepts all sensor types in one detector. Simply attach the specific toxic or combustible sensor to the universal detector head and the Meridian gas detector will automatically determine the type of gas to be detected. Installation of the sensor is a simple plug-and-play action. At Teledyne Gas and Flame Detection, we are always looking to anticipate your future needs. We designed the Meridian gas detection platform to be future proof, allowing you to take advantage of new sensing technologies from Teledyne Gas and Flame Detection while maintaining ease of use and peace of mind.
-
Product
Thermopile Detectors and Sensors
-
Our Thermopile Detectors are typically Thermopiles with integrated Thermistor providing analog output in various packages. Special designs include built-in lenses or reflectors to enhance sensing performance, Isothermal constructions, or Dual narrow-band windows. Our latest Thermopile Sensors include specially designed electronic circuitry to provide calibration, digital output, and functionality. With the DigiPile, Excelitas offers a unique design for measurement applications. With its digital output, this device does not require any low noise amplification. The CaliPile family provides integrated features that enable measurement, as well as presence detection applications.
-
Product
Pyroelectric Detectors
-
Pyroelectric detectors are thermal detectors; i.e. they create an electric signal due to temperature changes in the chip. This temperature change is caused by absorption of light. We do use LiTaO3 and DLaTGS as pyroelectric materials. Basically such detectors cover the whole spectra. However, they are mainly used for mid-wave and long-wave infrared detection (MWIR and LWIR). In addition, the usage in the THz region seems to become more popular these days.
-
-
Product
Phantom Surface/Web Metal Detector
-
Phantom Surface Web Metal Detection systems are designed to detect metallic fragments in wide, sheeted materials, continuous webs, and other thin products like textiles, paper, boards, food packaging, boxboard, poly films or products packaged on a roll/web.
-
Product
Stealth Web / Textile Metal Detector
-
Stealth Web metal detectors are custom manufactured to inspect products typically sheeted or on a roll / web. Stealth web detectors are ruggedly built to ensure product integrity and provide machine protection against metal fragments. The Stealth uses digital signal processing technology and has high sensitivity levels to ensure the detection of the smallest ferrous, non-ferrous and stainless steel contaminants.
-
Product
Thin Film Based Thermopile Detector: 1 Channel
DR46 Compensated
-
A one-channel compensated thin-film thermopile in a TO-8 package. The active area and compensating element area are 4mm x 0.6mm each. Offers high output with very good signal-to-noise ratio. Internal aperture minimizes channel-to-channel crosstalk increasing sensitivity.
