Current
See Also: Direct Current, Alternating Current, Resistivity, Flow, Inductance
-
product
Elevated 2.67 (76.00) - 7.00 (198.00) High Performance Lead Free Probe
LFRE-72T20-7
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
-
product
Fail Safe Waveguide Switches
Waveguide switches enable very rapid switching between two RF channels. Fail Safe Waveguide Switches return to the de-energized position when the power is disconnected and requires a small holding current in the energized position. All models have low VSWR and high power handling capacity. They withstand the full power rating of the waveguide and most models can be pressurized to 0.2 MPa (2 ATO) for high peak power applications.
-
product
Power Measurements Conditioner
The Power Measurements Conditioner provides voltage and current signal conditioning for a supported data acquisition module or device to make up to four simultaneous power measurements per conditioner. It also includes attenuation for voltage channels up to 2,000 V and has power, communication, and signal lines for current measurements from current transducers.
-
product
C/I Clamp Meters
*AC current measuring capability up to 400 amps*Compact size, fits easily into tool pouch*Data hold and Max hold to capture important readings*Lifetime Limited Warranty
-
product
Alternate 0.78 (22.00) - 3.70 (105.00) General Purpose Probe
HPA-0B-1
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 635Overall Length (mm): 16.13
-
product
Regulated Transmitter
VIP 4000
The VIP series of Electrical transmitters are purposely designed for deep induced polarisation or Resistivity sounding investigations. The Vip injects a regulated current into the ground.
-
-
product
Horizontal Measuring Instruments
Horizon Granite
The «Horizon» instruments respond to the current requirements for quality inspection in manufacturing areas. They allow a quick, precise checking and setting.
-
product
Bench Power Supply, DC, Single, Adjustable, 1 Output, 1 V, 36 V, 0 A, 3 A
72-8345A
Switch Mode Laboratory DC Power Supplies Precision adjustable supply provides adjustable 1~36VDC output with adjustable current limiting from 0~3A. It is ideal for test, measurement and service applications where tight voltage and current regulation are critical. Highly efficient switch mode design delivers outstanding performance from an extremely compact footprint. Unique separate output ON/OFF control allows voltage and current setting, with the supply output turned off. Part of a Complete Series, this slim supply occupies little bench space while providing very high precision and 90W of continuous output.
-
product
Standard 1.09 (31.00) - 4.50 (128.00) Long Travel Bead Probe
BPLT-1HF-4.5
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 350Full Travel (mm): 8.89Recommended Travel (mil): 317Recommended Travel (mm): 8.05Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,450Overall Length (mm): 36.83Full Travel Remark: Standard Spring: 400 mil / 10,16 mm, High Spring: 350 mil / 8,89 mm
-
product
Alternate 2.39 (68.00) - 6.00 (170.00) High Performance Bias Ball Probe
POGO-1T-6-S
Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 1,000,000Overall Length (mil): 1,300Overall Length (mm): 33.02
-
product
Sound Level Meter
831-LOWN
Easily make low noise measurements to 6.5 dB A-weighted using the Model 831-LOWN sound level meter paired with the 378A04 low noise microphone and preamplifier. Due to the innovative design of the 378A04 which uses a prepolarized microphone and ICP (constant current) interface, the combination produces a highly portable system that is battery powered and intuitive to use for measuring low noise levels.
-
product
Atlas SCR Thyristor and Triac Analyser
SCR100
Thyristors and Triacs need special test conditions to analyse effectively - that's where the new Atlas SCR comes in. The SCR100 can apply gate test currents from 100µA up to 90mA (with test load currents of up to 100mA) so it's not limited to sensitive parts.It will automatically identify the type of part (Thyristor or Triac), identify all three leads and also categorise the gate sensitivity. This new version takes a standard Alkaline AAA battery.
-
product
Recording Ammeter
Amcorder
The Amcorder uses the same sensor technology as the original Ampstik. The True RMS inductive sensor does not use magnetic materials and has no moving parts. The opening of the sensor is electronically closed and external currents are electronically rejected. The accuracy, external current reject, and range of currents measured by the patented amp sensor substantially exceed the performance of the best clamp-on sensors. The key feature of the unit is the ability to leave it deployed on the line to record average current readings every 15 minutes for 30+ days. It easily attaches to the line with a standard shotgun style hot-stick. Once on the line, it immediately begins to collect and record the current load on the line.
-
product
Ground Bond Tester,
266
Our 266 Model makes Ground Bond / High Continuity Testing simple with 60 Amps of current to satisfy your toughest NRTL standard. With an intuitive interface that allows you to set-up a test in seconds and practical security settings, our 266 can easily be deployed in both laboratory and production line environments. Ensure every Ground Bond Test is accurate with our Milliohm offset function.
-
product
PXI 40Amp 14Volt 4xSPST Automotive Relay
40-180-101
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC. The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
product
AC/DC TRMS Insulation Clamp Meter
CMi210
A unique insulation clamp meter for the installation, testing and maintenance of domestic and industrial installations. This high specification clamp meter can perform insulation tests to 6G Ohms with 5 test voltages from 50V to 1000V.
The clamp provides True RMS measurement of AC current to 1500A and AC voltage to 750V. It will also measure DC current to 2000A and DC voltage to 1000V. The CMi210 has all the same test functions you would expect to find on a high specification multimeter with the added benefit of temperature measurement.
-
product
Device Characterization Software with Test Automation
14565B
The Keysight 14565B device characterization software is designed for easy evaluation of portable battery powered device (like 3G handsets, PDA, WLAN, and Bluetooth enable devices) current profiles to ensure long operating life of devices.
-
product
ABex Current Sense Module for Six Channel UUT Supply Monitoring
ABex TM-406 Current Sense
The ABex TM-406 is a six-channel shunt current measurement extension. It’s designed to work in combination with the Konrad ABex TM-501 and PXI-501.Each of the six shunt current measurement units have a passive measurement shunt, an overcurrent protection, a sense bridge relay and the possibility to route the quiescence current to an ABex measurement device TM-501 with PXI-501.In addition, the ABex TM-406 features 8 isolated digital outputs (IDOs), and 12 measurement inputs, which can be routed to the analog bus.
-
product
Digital Input Scanner
IM2030
Available with us is a digital input scanner that shows the status of digital / potential free inputs connected to the unit. The units are available with 8/16/32 inputs and the names for each input can be configured for easy identification. MODBUS interface is provided to transmit the current status of the inputs to pc.
-
product
Standard 1.10 (31.00) - 2.50 (71.00) General Purpose Probe
HPA-1D
Current Rating (Amps): 3Average Probe Resistance (mOhm): 35Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 100Full Travel (mm): 2.54Recommended Travel (mil): 67Recommended Travel (mm): 1.70Mechanical Life (no of cyles): 1,000,000Overall Length (mil): 655Overall Length (mm): 16.64
-
product
PXI 2 Amp MUX, Single 16-Channel 4-Pole
40-635-003
The 40-635 2 Amp Multiplexer module is available in 9 standard configurations as well as 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.The module is suitable for signal routing in ATE and data acquisition systems. Connections are made via a front panel 78-way D-type connector.
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, Twin Female
610138200
Primary mating contact 610138118. (May mate with other Male Adapter and ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCu/PhBrzContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAvg Mating Force(lbs) 0.24
-
product
Alternate 2.14 (61.00) - 6.00 (170.00) High Performance Lead Free Probe
LFRE-72U-6
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
-
product
BIP-8 Battery Probes
Current Rating (Amps): 5Average Probe Resistance (mOhm): 30Test Center (mil): 188Test Center (mm): 4.78Full Travel (mil): 90Full Travel (mm): 2.29Recommended Travel (mil): 60Recommended Travel (mm): 1.52Overall Length (mil): 396Overall Length (mm): 10.06
-
product
Leakage Current Clamp Tester with Bluetooth
M-1141XR
MULTI MEASURING INSTRUMENTS Co., Ltd.
・Waveform display is possible with connection to a smartphone・Measurement data is to be accumulated in the server, and it is available for graph and CSV output・Auto 5-range : AC 30mA / 300mA / 3A / 30A / 300A・CT inside diameter : φ40mm・Minimum resolution : 0.01mA・Maximum value hold / Data hold function available・Band path filter with center frequency (fo = 55Hz)・Compliant with EN 61010, CAT-III 1000V / CAT-IV 600V・With backlight
-
product
Diode Driver & Laser System Controllers
The laser controllers provide a simple method of controlling Lumina and other popular laser diode drivers or full laser systems. They include the ability to easily control current levels, pulse modes, and interlock controls as well as monitor voltage and current levels as well as q-switch triggering, external triggering, sync output, and additional I/O signals.
-
product
AMI Meter Farms
Do you have new AMI meters going into the field? Or have you already deployed your new meters, but will have firmware upgrades soon? Allow us to introduce the TESCO Meter Farm, our newest offering to support your AMI Meter Deployment. The Meter Farm powers up banks of meters and runs a current load through each meter. TESCO Meter Farms are designed to serve as a cost effective method for testing communication, functionality and firmware upgrades from your meter manufacturer(s). The Meter Farm can be used as part of the qualification process prior to deployment, but has been more popular as a post deployment tool to allow large scale testing of all new releases of firmware over hundreds or even thousands of meter points prior to upgrading the entire system. The Meter Farm can also be used to perform long term testing for new hardware releases prior to introducing later generation meters into the field. As with all of our products, the TESCO Meter Farm is built with the tradition of reliability and ruggedness.
-
product
Electronic Load System
Electronic loads are required for testing fuel cells such as PEMFC, AFC, PAFC, MCFC, SOFC. These electronic loads are designed either in IGBT technology with power, current and voltage ranges according to specific requirements or in transistor technology. Electronic loads in IGBT technology are designed for high voltage ranges up to 900 V, current ranges up to 1000 A, and power ranges up to 480 kW.
-
product
High 3.12 (88.00) - 8.00 (227.00) High Performance Lead Free Probe
LFRE-72U-8
Current Rating (Amps): 3Average Probe Resistance (mOhm): 15Test Center (mil): 50Test Center (mm): 1.27Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Overall Length (mil): 1,700Overall Length (mm): 43.18
