PCI Backplanes
-
Product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
Programmable Potentiometer
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI 2 Amp Multiplexer, Single 32-Channel, 1-Pole
50-635A-101
Multiplexer Module
The 50-635A-101 is a single 32-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
4, 8, 16, 32 Channel ARINC429 Test And Simulation Module For PCI
APXX429-x
Simulator
ARINC429 Test and Simulation bus interface with 4, 8, 16 or 32 Software programmable Tx/Rx channels plus up to 8 Discrete I/O’s.
-
Product
Stepper Motor Controller for PCI
PCI322
-
The PCI322 Intelligent Stepper Motor Controller is designed to drive external amplifiers. This is an ideal solution for all applications where stepper motors must be controlled with a maximum of flexibility and a minimum of overhead. The local processor handles all high-level commands to provide maximum control for both straightforward as very complex applications
-
Product
Low Profile PCI Express 1-Port
7106e
-
The 7106e low-profile PCI Express serial interface provides a single serial port configurable for RS-232, RS-422, RS-485 or RS-530. The ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allows the adapter to support the widest range of standard and non-standard baud rates exceeding 921.6 K bps. These features make the 7106e ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
PCI & PXI Signal Amplifiers
-
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
Product
PCI Express Mini Module
-
PCI Express Mini Module provides a simple and standardized way to add I/O and storage functions to embedded board without increasing the overall size.
-
Product
PCI 64xSPST Reed Relay Card
50-115A-121
Reed Relay
This is the 64xSPST version of our 50-110A/50-115A range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
PCI High Density Matrix, Single 22x8 1-Pole
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
PCI High Density Pecision Resistor Card, 3-Channel, 3.5Ω To 773kΩ
50-298-143
Programmable Resistor Module
The 50-298-143 is a high density programmable resistor card with 3 channels which can be set between 3.5Ω and 773kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
-
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm
50-294-023
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI Smart Bus Extenders
Live Insertion PCI Bus Extenders
-
The Ultraview PCIEXT64 extender series offers excellent PCI signal integrity, due to high speed trace layout, including high impedance signal traces and minimal ground inductance, as well as active bus isolation, to ensure minimal effect on the board-under-test. Power monitoring and current limiting features allow a robust debug and test environment. The capabilities of Ultraview's two models of Universal 66/33MHz 64/32-bit PCI extenders are as follows:
-
Product
Rugged High speed, VITA Backplane Connector System
KVPX Series
-
Smiths Interconnect's KVPX series is the most rugged VITA compliant backplane connector on the market.
-
-
Product
PCI 48 Channel TTL Digital Interface
8005
-
The 8005 digital I/O interface provides 48 channels of buffered drive digital I/O emulating 8255 mode zero, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
PCIe-8398, x16 Gen3, PCI Express Host, 13.6 GB/s Device for PXI Remote Control
784179-01
Remote Control Interface
The PCIe-8398 is a host interface card used to control a PXI Express chassis over a software-transparent PCI Express Gen 3 x16 link. The PCIe-8398 is installed into a x16 PCI Express slot of a desktop or rackmount PC and is connected to a PXIe-8398 or PXIe-8399 PXI remote control module using Gen 3 x8 copper cables.
-
Product
PCI-6221, 16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device
779418-01
Multifunction I/O
16 AI (16-Bit, 250 kS/s), 2 AO, 24 DIO PCI Multifunction I/O Device - The PCI-6221 offers analog I/O, correlated digital I/O, two 32-bit counters/timers, and digital triggering. The device delivers low-cost, reliable DAQ capabilities in a wide range of applications from simple applications in laboratory automation, research, design verification/test, and manufacturing test. You can add sensor and high-voltage measurement capability to your device with SCC or SCXI signal conditioning modules. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
8 SE Or 4 Diff. Input Channels, 4 Analog Current Output Channels, PCI Express
APCIE-3121-8-4C
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
PCI Single 22 X 8 Matrix 1 Pole Screened
50-512-021-S
Matrix Switch Module
The 50-510 series of matrix cards feature a wide range of selectable switching configurations (22x4,dual 20x4,22x8 and 44x4). Larger matrices may be constructed by Daisy Chaining the common signals from multiple PCI cards. For example four 44x4 Cards will form a 176x4 Matrix, a total of 704 crosspoints. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
32-CH/64-CH Isolated Digital I/O PCI Express Card With Digital Filter
AX92351
-
The AX92351 is a 64-ch isolated digital I/O PCI Express card with 2,000VDC isolation protection. This high-density digital I/O card with high-speed PCI Express x1 bus is excellent for use in applications requiring digital control or monitoring, such as semiconductor machinery, PC-based industrial machinery, programmable I/O logic control, and process status monitoring. The AX92351 features 32 isolated digital input channels and 32 isolated digital output channels with isolation protection of 2,000V for industrial applications where high-voltage isolation is required. It is equipped with a board ID feature for easy identification of multiple cards in single system. There is a digital filter function to prevent input signals from carrying noise or a chattering. Each isolated input has a sink or source current which supports dry and wet contact for maximum application flexibility. The card has a wide range of input voltage from 10 to 30V to meet most industrial application needs. The AX92351 also provides two interrupt sources on digital input channels. Digital output has open controller and supports maximum 30VDC. The read-back function is another useful function that allows monitoring each output port.
-
Product
PCI Very High Density Multiplexer, 10-Channel, 8-Pole
50-670C-021-10/8
Multiplexer Module
The 50-670C-021-10/8 is a 10-channel, 8-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 52.4kΩ
50-297-033
Programmable Resistor Module
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI To PCI Express Board
MS 1718
-
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
Product
PCI-5122, 100 MHz Bandwidth, 100 MS/s, 14-Bit PCI Oscilloscope Device
778758-02
Oscilloscope
100 MHz Bandwidth, 100 MS/s, 14-Bit PCI Oscilloscope Device—The PCI‑5122 high-resolution oscilloscope device has two channels with greater than 75 dBc spurious‑free dynamic range (SFDR) and flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for both time-domain and frequency-domain applications that require high-resolution, low-noise measurements with up to 100 MS/s and 100 MHz of analog bandwidth.
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 925Ω
50-298-121
Programmable Resistor Module
The 50-298-121 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 925Ω with 0.25Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
4-Port PCI Express CoaxPress 12 Frame Grabber
PCIE-1164-AE
Frame Grabber
Half-Size PCI Express Board Gen 3.0 x8CXP speeds range from 3.25 to 12.50 Gb/SSupports 1 to 4 CXP-12 camerasSupports power for all cameras with SafePower (up to 13 Watts per link)Supports NVIDIA GPUDirectFull GenICam support for control and captureSupports quadrature encoders
-
Product
PCI High Density Pecision Resistor Card, 4-Channel, 3Ω To 6.97kΩ
50-298-130
Programmable Resistor Module
The 50-298-130 is a high density programmable resistor card with 4 channels which can be set between 3Ω and 6.97kΩ with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PCI High Density Resistor Card 10-Channel, 16-Bit, 0 To 65k Ohm
50-295A-121-10/16
Programmable Resistor Module
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
PCI High Density Matrix, Dual 20x4 2-Pole
50-511A-022
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
