Programmable Attenuators
-
product
Dual Attenuator
V859
The Model V859 is a passive dual section attenuator housed in a 1-unit VME module; the module does not require any power supply since it is made up of resistive cells
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-156
The 40-297A-156 (PXI) and the 42-297A-156 (PXIe) are 3-channel programmable resistors with a range of 3 Ω to 85.3 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
CCS Programmers & Debuggers
Fast & Easy-to-useComplete & Cost EffectiveUSB Connection to PCPower Target Board Through USBICD & ICSP™ Programmer/DebuggerDebug Support Covers all Targets
-
product
Programmable LED DC Electronic Load
M98 Series
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
product
Programmable, 2-Channel Low-Pass Filter Module
AAF-2Fe
Programmable, 2-Channel Low-Pass Filter Module. The AAF-2Fe may be used with the AAF-3PCI, AAF-3, AAF-2, or AAF-1 filter boards.
-
product
HVFO10X +/-20V (20x Attenuation) Universal Tip Accessory
HVFO100-20X-TIP-U
HVFO10X +/-20V (20x Attenuation) Universal Tip Accessory.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-134
The 40-297A-134 (PXI) and the 42-297A-134 (PXIe) are 4-channel programmable resistors with a range of 2 Ω to 102 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Precision Resistor Module 9-Channel, 1.5 to 3.55k
40-297-023
This 9-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Digital Step Attenuators (DSA)
High linearity, fast switching time with broad bandwidth. Best-in-class attenuation error with fine attenuation steps. Most robust ESD protection available.
-
product
Manual Attenuator (Waveguide)
RF Lambda’s manual waveguide attenuators are used to control signal levels using a manual control knob. These are commonly used in test setups or systems where an operator is present and there is a need to change signal levels manually.
-
product
Single Channel USB Programmable Instrumentation Amplifier
USBPIA-S1
The USBPIA-S1 stand alone USB controllable module provides a single channel of high-quality instrumentation amplifier and optional AC coupling, for front-end signal conditioning compatible with all popular A/D converter devices. The USBPIA-S1 is powered with 9 to 12VDC so it can be connected to a battery voltage source or the supplied 115-220VAC adapter may be used for operation with wall power anywhere in the world. When programmed from the USB port, the USBPIA-S1 will remember all of the programmed properties between power cycles. Program once and operate as a stand- alone signal conditioner without having to reprogram for every use. This is perfect for turn-key applications. It's easy to connect the USBPIA-S1 into the data collection system. Input and output signals can be routed through BNC connection or using the detachable screw terminal connectors. Optional SMA type adapters are also available.
-
product
Attenuator Banks
HYTEM offer different RF attenuation systems that allow to perfom simultaneous types of tests on multiple RF links (handover for instance). Multiple configurations are available : Standard, MIMO, Link separation, Spécific.
-
product
4G Concurrent Device Programmer for PC /USB (4 sockets)
ProMax 4G
ProMax is the most innovative and cost effective 4- or 8-gang programming solution on the market. ProMax supports a wide variety of programmable devices. Its state-of-the-art technology and high-speed programming algorithms optimize throughput, reliability and yields.
-
product
Low Power Programmable AC Source
Chroma Systems Solutions, Inc.
Delivers pure, instrument grade AC power at very low cost with output voltage from 0 to 300VAC, and frequencies from 15 to 1000Hz
-
product
Millimeter Wave Continuously Variable Waveguide Attenuators
Our millimeter wave variable waveguide attenuators allow designers and engineers to test their systems at various signal strengths and attenuation values to determine the optimum signal performance of the system. The key feature of these waveguide attenuators is that the attenuation level is adjusted using a built-in micrometer which enables repeatable and rapid re-setting to different attenuation levels without the need for additional external components. Our waveguide attenuators handle varying attenuation levels from 0 to 30 dB over the specified band allowing the designer to tune the attenuation level needed for the application. These continuously variable waveguide attenuators cover a broad frequency range of 33 to 110 GHz in five bands and also display flat performance across a wide band with low insertion loss.
-
product
Synchro/Resolver Simulator, Programmable
5330A
NAI's 5330A Synchro/Resolver Simulator is a rack-mount or bench-top instrument featuring integrated touch-screen controls and input terminals. This model represents a major step forward as it uses digital technology to produce Synchro and Resolver outputs. Improved flexibility is provided by two fully independent outputs that can be used to simulate two separate Synchro or Resolver signals simultaneously, or can be combined to operate as two-speed outputs. The versatility of this device has been substantially increased by incorporating dynamic modes that enable servo systems to be tested under various simulated stringent field conditions.
-
product
PXI Precision Resistor Module 4-Channel, 1.5 to 472
40-297-120
This 4-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Programmable Parametric Tester For Discrete Semiconductors
IST-8800
IST Information Scan Technology, Inc.
The IST-8800 is a fully programmable, low cost tester that provides parameter measurements or parametric GO/NO GO test for transistors, diodes, MOS-FETs, Regulators, Triacs, Zeners, SCRs, and J-FETs. These devices can be tested up to 5 amps or 1200 volts with a measurement range down to the nano amp range. Only four universal test fixtures are required which can test the device across a wide range of packages.
-
product
Programmable DC Electronic Load
63000 Series
The 63000 Series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power suppl ies, A/D power suppl ies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices. The 63000 Series offers models in two operating voltages 150V models, with 250W and 350W power levels up to 60A in a single unit. Their compact and light weight design make these loads easy to move around which is ideal for R&D and design validation. Each model of the 63000 Series has unique user-def ined waveform (UDW) funct ion capable of simulating real-world custom waveforms. In addition, a data storage function has been built in for saving and recalling up to 100 stored settings at any time. For automated testing, these save and recall functions can save a great deal of time. The 63000 Series has 3 power ranges that can precisely measure the voltage and current in real time. Since short circuit testing is a critical test item, the 63000 provides short circuit simulation to effectively address application demands for power and automated testing.
-
product
PXI Precision Resistor Module 3-Channel, 2.5 to 201k
40-297-141
This 3-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 470Ω
40-251-114
The 40-251-114 is a programmable resistor module with 4 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 3Ω to 5.82MΩ
40-252-052
The 40-252-052 is a programmable resistor module with 1 channel which can be set between 3Ω and 5.82MΩ with 0.5Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI Programmable Resistor Modules
Part of our Sensor Simulation family, these PXI programmable resistor modules are ideal for medical, aerospace and automotive applications. A programmable resistor is designed to simulate the use of resistive sensors and variable resistors in systems when testing devices such as engine controllers.
-
product
Hardware Security For Programmable System Control
Mach-NX
*Up to 8.4K LC of user logic, 2669 kbits of user flash memory and dual boot flash feature*Up to 379 programmable I/O supporting 1.2/1.5/1.8/2.5/3.3 I/O voltages*Secure enclave supports 384-bit cryptography, including SHA, HMAC, and ECC*Configuration of PFR and security functions through Lattice Propel simplifies developer experience*Highly reliable. Low power and 3X better SER performance to comparable CMOS technologies
-
product
High-Precision Programmable DC Power Supply
MPS-3600H Series
MPS-3600 HSeries is a new generation of high-precision programmable DC power supply. This series of products is equipped with a standard communication interface, which has both desktop and system characteristics. It can be arbitrarily matched with other instruments and integrated into a special function test system to complete the measurement requirements in different occasions.
-
product
Millimeter-wave and Microwave GaAs Attenuators
Keysight Technologies provides MMIC attenuators ideal for microwave radio, aerospace and defense, and instrumentation applications.
-
product
Attenuator Interconnect Kit, SMA
11716C
The Keysight 11716C quickly and conveniently connects 1 dB step and 10 dB step attenuators together to achieve greater dynamic range with 1 dB steps. The Keysight 11716C can be utilized to connect any of the two Keysight 8494/95/96 attenuators in series.
-
product
Programmable Relays
You get in one unit 12 Inputs and 8 Outputs relays or transistor. Herewith you can do a lot of bigger scale automation whereas the 10 I/O versions are just to short of I/O’s.
-
product
HVFO10X +/-5V (5x Attenuation) Universal Tip Accessory
HVFO100-5X-TIP-U
HVFO10X +/-5V (5x Attenuation) Universal Tip Accessory.
-
product
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A
T3PS30063P
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A.
