Pyroelectric Sensors
Turn absorbed radiant energy into a current or voltage.
See Also: Thermopile Sensors
-
Product
Inductive Sensor
Ampstik®
-
The Ampstik is easy to use and provides accurate information to anyone working with medium and high voltage. It gives line personnel the right answers so they have the ability to make decisions in the field.
-
Product
TMR Gear Speed Sensors
-
MultiDimension Technology Co.,Ltd.
Magnetic gear tooth sensors utilize a unique push-pull Wheatstone bridge design, including one or two Wheatstone full bridges, with four or eight unshielded high sensitivity TMR sensing elements. The Wheatstone bridge creates a differential voltage output with respect to the magnetic field gradient along the sensor’s sensitive direction.
-
Product
Single Axis AC Magnetic Field Sensor
MGC-1A
-
Macintyre Electronic Design Associa
The MGC-1A is a low noise high sensitivity single axis AC magnetic field sensor used for the measurement of audio frequency fields. Because of its innovative design, the MGC-1A amplitude response is insensitive to the frequency of the field over its 30 Hz to 10 kHz frequency band. Accuracy at 1 kHz is ±1%, and the amplitude response stays within 2 dB peak-to-peak over the bandwidth.
-
Product
Sensors
NanoFocus Probe
-
Scan of 3D topography of high accurate featuresVery high point densitySuitable to perform non-contact roughness measurementsHigh flexibility using a range of different front lenses
-
Product
Sensors
-
To measure machinery or structural vibration, a transducer is needed to convert the mechanical motion into an equivalent electrical signal. Each sensor has distinct advantages in certain situations and limitations in other, so it is important to select the most suited transducer or sensor for your job. Equally, important is selecting the appropriate parameter of vibration amplitude for measurement. IRD® has a wide range of transducers and accelerometers available to help you obtain accurate, reliable data, whether your concern is vibration monitoring, analysis, or dynamic balancing.
-
Product
hyperspectral imaging sensor
Hyper-Cam
-
The Hyper-Cam is a lightweight and compact hyperspectral imaging sensor which uses Fourier Transform Infrared (FT-IR) technology. This advanced high-performance spectrometer allows to detect and identify substances either gases or solids from a distance of up to 5 kilometers. It provides real-time chemical imaging as well as unparalleled spatial and spectral information about the IR targets under measurement.
-
Product
Convergent Reflective Micro Photoelectric Sensor
PM2
-
Panasonic Industrial Devices Sales Company of America
The fixed beam of focused light from the Convergent Reflective Type Micro Photoelectric PM2 Sensor enables it to precisely detect an object within a defined sensing range. With the ability to measure independently of the background, the PM2 Sensors are also able to detect dark or slightly reflective objects as well as extremely thin objects (> 0.05mm). These features, combined with its compact and robust design, make the PM2 Sensor suitable for a large number of applications.
-
Product
LED Type Wafer Alignment Sensor Controller
HD-T1
-
Panasonic Industrial Devices Sales Company of America
The HD-T1 Series is a new Wafer Alignment Sensor that uses a safe red LED light beam, with a resolution of 30µm, to achieve the same high level performance as Laser Sensors. The HD-T1 Sensor is best suited to detect wafer eccentricity, notches and orientation flats. Using linear image Sensor methodology and high-speed sampling technology, a wide variety of objects can now be stably measured with great precision at ultra-high speeds. This CCD style Sensor is developed for use in almost all fields of industry, e.g. tire manufacturing or Semiconductor production (Wafer Printed Circuit Boards).
-
Product
Ambient Light Sensors
-
ST offers innovative ambient light sensors (ALS) that provide, in optimized package size, accurate information on ambient light, like the Illuminance (lux) level, the color temperature or the light flicker frequency.
-
Product
Vision Sensor
BOA Spot
-
Introducing BOA Spot: simple, affordable, and reliable performance for quality inspection. No matter what you create on your production line, BOA Spot can help you improve quality, reduce scrap, and increase throughput. It has never been so easy for you to expand your automation with vision.
-
Product
Industrial Oxygen Transmitters with Zirconia or Electrochemical Sensors
-
The range of Oxygen Transmitters from PST are compact and robust devices that utilise zirconia, solid state ceramic or electrochemical sensing technologies to give a reliable measurement of oxygen concentration.
-
-
Product
Sensors
-
A speed and angle sensor using a black/white tape which is glued on a rotating part. The reflection is converted into a TTL signal, bandwidth 100 kHz. The sensor consists of a tiny electronics part and a 5 m fiber optic cable terminated with a M6 screw. Thus areas where space is very limited still can be reached conveniently.
-
Product
Image Sensor Testing
IP750Ex-HD Family
Test System
The IP750EX-HD has been the test platform that has enabled the industry to manufacture high quality CCD and CMOS image sensors, and it is the most economical platform to meet the needs of newer technologies such as Time of Flight (ToF) sensors. When you use a smartphone, high performance digital still camera, or in-home security and surveillance system, these applications have image sensors most likely tested by Teradyne’s IP750ExHD.
-
Product
Proximity Sensor
-
Tubular Inductive Proximity Sensor,Rectangular Inductive Proximity Sensor, Inductive Ring Sensor, Capacitive Proximity Sensor
-
Product
TMD37003 cRGB Color and Proximity Sensor
SEN-36004
-
Fully integrated carrier board designed to get the most out of the TMD37003 cRGB (color with IR compensation) and Proximity Sensor from AMS. This means that the board includes a 1.8V-5V input range LDO and high-speed signal voltage translation on all IO pins. In addition, we've added a high output white LED that is tuned to the light temperature range of the TMD37003 IC. This makes sensing color of close-proximity objects possible, such as in robotic color sorting operations. As on many of our boards, we've included 4-40 sized mounting holes to make installation easy. The IC functions are interfaced via a 0.1" header, which includes power (Vdd and GND), I2C interface (again, fully translated) and a 3.3V input to power the proximity (IR) LED. The on-board LED is turned on with a logic 'HIGH' applied to the LED pin and is powered with Vdd.
-
Product
Presence Sensor
X4M300
-
The XeThru X4M300 is Novelda’s presence and occupancy sensor powered by the XeThru X4 ultra wide band radar chip. Ultra sensitive and with excellent signal to noise performance, the sensor detects even the smallest human movement in a room.
-
Product
Light-to-Analog Sensors (Voltage)
-
Renesas' light-to-voltage silicon optical sensors combine a photodiode array, a non-linear current amplifier and a micropower op amp on a single monolithic IC. Applications for these devices include display backlight control, keypad dimming, anti-glare mirror systems, and industrial and medical light sensing applications.
-
Product
Hyundai Oxygen Sensor
KS60113 - Hyundai
-
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
Product
Integrated Current Sensors
FHS Series
-
*Standard package and small footprint*Cost effective*Standard SOIC 8 surface mount PCB
-
Product
Magnetic Sensors
-
Magnetic sensors are used for the detection of positions without contact or wear and tear. They are used where very long sensing ranges are required. Since magnetic fields penetrate all non-magnetisable materials, the sensors can detect magnets through walls made of stainless steel, aluminium, plastic or wood.
-
Product
Split Type AC Current Sensor
CTF-6
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*For AC current and power measurements.*Ultra compact size and high accurate output linearity.*Easy installation in the distributing box.*Compliant with RoHS drective.
-
Product
Ultrasonic Sensors
-
Omega's ultrasonic sensors provide non-contact measurement for a virety of factory and process control applications including tank level, roll diameter, proximity, dimensioning, and web break and
-
Product
MEMS And Sensor Test Automation Platform
Sense+
-
Sense+™ ultra-precise MEMS & sensor test automation platform allows for significant improvement in test accuracy, parallelism for a lower cost of test, and the ability to handle and inspect, small delicate sensors. Fully configured, Sense+ delivers a one-pass automated test, inspection, and metrology for the most complex MEMS devices including <1 mm WLCSP.
-
Product
Duct Type Wind Speed Sensor
WSA
-
Due to environmental quality management and energy management, we've developed WSA, wind speed sensors which can be applied on ventilation systems, air conditioning, and negative pressure rooms. WSA is a high-accuracy duct type wind speed sensor which can quickly measure the small wind speed. It is stable, high-accurate, and with small drift only. Also, it can caculate the value of the current air volume depending on the measured cross-sectional area of the ducting. Ducting installation and screwless terminals help the users work more easily. Besides, the sensor is equipped with EMC anti-interference devices so that it can withstand strong electromagnetic interferences.
-
Product
Integrated Current Sensors
HMSR series
-
The HMSR is a new generation of high insulated Integrated Current Sensor from LEM. These product family provides a robust, compact and very accurate solution for measuring DC and AC currents in all highly demanding, switching power applications for commercial, industrial. HMSR is a micro core based open loop sensor with a reinforced insulation and overcurrent detections (user configurable and factory set). These features make the device suitable for high voltage applications requiring high precision and strong immunity against external field. The primary conductor (pins 1 and 8) has very low electrical resistance and dedicated pads d
-
Product
Liquid Sensors
-
Panasonic Industrial Devices Sales Company of America
These compact Liquid Sensors detect small leaks, liquid and air bubbles in small tubes and determine liquid levels. Using a capillary effect, the EX-F70/F60 Sensor Series delivers high speed detection of small leaks with a 50 ms response time, with highly chemical resistant and space saving models.
-
Product
Compressed Air RH+T+Tdp Sensor
T0211P-2
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
Fluid Level Sensor
-
The output of the fluid level sensor is a voltage which changes in direct proportion to the level of fluid in the probe. The difference in permittivity between air and the fluid being measured changes the capacitance between the probe's two concentric tubes as the level changes. An RS232 connection to a PC allows the user to calibrate the fluid level and thermal drift compensation. The probe is factory replaceable, allowing the electronics to be re-used should the probe become damaged or if a new probe length is required.
-
Product
ST VL53L0X Time-of-Flight Range/Distance Sensor
SEN-36003
-
Highly integrated breakout board for the ST Micro VL53L0X Time of Flight (ToF) range finder sensor, which builds on the absolute ranging technology introduced with the VL6180X. The VL53L0X drops the ambient light sensing capability of it's predecessor for a 10X improvement in absolute ranging capability, bringing the maximum possible range to 2 meters! As a result, this sensor has even more uses in the robotics, cell phone and gesture recognition space. The SEN-36003 includes the VL53L0X IC mounted between two 4-40 sized mounting holes with on board 2.8V LDO and high-speed signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. All pins are translated to allow interfacing with any microcontroller in the 3V to 5V operating range.
