Partial Discharge Monitors
See Also: Partial Discharge, Partial Discharge Detection, PD, PD Test, Partial Discharge Test
-
Product
Aerosol Monitor
DUSTTRAK II-8530
-
The DUSTTRAK™ II Aerosol Monitor 8530 is a desktop battery-operated, data-logging, light-scattering laser photometer that gives you real-time aerosol mass readings. It uses a sheath air system that isolates the aerosol in the optics chamber to keep the optics clean for improved reliability and low maintenance.
-
Product
Fiber Monitoring System for Optical Networks
-
Detecting serious physical network infrastructure issues like accidental fiber cuts, intrusion attempts, and malicious tampering has never been easier than utilizing this Fiber Monitoring System available from M2 Optics. The first solution approach in the industry that was designed to minimize monitoring costs on a per-fiber basis, all the hardware and software are integrated into a single low-profile chassis for fast deployment to cover your critical links.
-
Product
Crane Safety Monitor
CSM
-
PIAB CSM Crane Safety Monitor is an electronic control unit to be used in overload protection systems. The PIAB CSM evaluates and computes signals from force transducers and can be set for alarm at preset alarm limits. By installing the PIAB CSM, hazards for personnel and material are avoided. The PIAB CSM will also record the operation of the hoist. The PIAB CSM is designed both for indoor and outdoor operation in aggressive and demanding industrial environments.
-
Product
10.1" Bezel-Less Touch Monitor
IDP31-101W
-
10.1" LCD wide screen panel with LED backlight delivers a long service life, Supports wide operating temperatures. True flat surface – contemporary Proflat design, Wide viewing angles support portrait and landscape modes.
-
Product
Advanced Monitoring Probe
DVB-S/S2
-
Combined with a Network Monitoring System or not, the EdgeProbe Advanced provides a powerful broadcast network alert & diagnosis tool allowing DTV network operators to monitor global trends and anticipate potential failures.EdgeProbe Advanced is able to monitor DVB-S and DVB-S2 signals before uplink and after downlink, through its RF inputs (up to 4 in 1RU), as well as baseband transport before satellite modulator and after IRD, through its ASI and IP inputs.
-
Product
Mark II Dual Setpoint Monitor
95006
-
A patented, precision, solid state motion sensor consisting of a sensing head (encoder) and a master control panel and enclosure, the Mark II features a digital tachometer and a two-set point system. Use of a dual set point system, properly set, assures warning of a potential problem, allowing corrective action before damage can occur, and providing total shutdown if the problem is not corrected.
-
Product
Advanced GNSS Spoofing Simulation And Monitoring
SimSAFE
-
SimSAFE enables better protection against GNSS spoofing attacks. GNSS spoofing is a growing concern for developers and users of critical systems, with many well-publicized instances occurring every year. In order for users to be assured that their equipment continues to perform as expected when exposed to fake or replayed GNSS signals, it is vital to test thoroughly.
-
Product
Multi SDI Monitor
LV 5381
-
The LV 5381 is a waveform monitor that can monitor up to four SDI signals simultaneously.It is optimized for the level adjustment of the outputs of multiple installed cameras. In the video signal waveform display, vector display, and picture display, multiple input signals can be displayed on top of each other or lined up next to each other.It is also full of useful features such as a level meter display for embedded audio, an error display that indicates transmission errors, and a 5-bar display that shows video signal peak levels using five bars. Furthermore, the LV 5381 can show different combinations of these displays in its multi-screen display.
-
Product
Noise Monitoring Kit
LxT NMS SoundExpert
-
In addition to the SoundExpert LxT meter, this kit includes the EPS042 protection case and D-cell battery pack, the EPS2116 microphone protection shroud, and EXC010 10 ft. cable. Using D-cell alkaline batteries, allows the noise monitor to be smaller and lighter; avoid the expense of shipping heavy lead acid batteries and the hassle of recharging. You can transport it easily to your site, deploy it, measure data, retrieve your system, download the data, and issue your report.
-
Product
GEM GroundHog Monitor
-
The G.E.M. GroundHog, a Multi-Ground Continuous Monitoring Automation System, is the newest addition to the robust ELITE family of electronics from Botron Company Inc. With a rich feature set never before available, ESD facilities and sensitive component manufacturers can monitor critical grounds in real time in applications ranging from the benchtop to capital equipment.
-
Product
The Nortech Fiber Optic Monitors
-
The fiber optic signal conditioners are designed for direct, accurate and real-time temperature monitoring to manage and maximize your transformer’s performance. The Nortech temperature monitor family comes in three different classes: the EasyGrid is the most comprehensive model, the EasyGrid LT is a compact and very cost-effective model for low channel count monitoring applications, and the EasyGrid Base is and even more compact model designed for easy network integration.
-
Product
Data Monitoring System
1S663-001
-
The 1S663-001 Data Monitoring System was specifically developed for the Cessna Citation X and serves as the primary diagnostic tool for the aircraft?? electronic Logic Modules. The system is FAA certified for airborne operation. Aft compartment and cabin modules can be tested two at a time while remaining in place. The system is also capable of monitoring the fuel quantity system during flight.
-
Product
Non-Dispersive Infrared Monitors
OPTI-Sense Series
-
Teledyne Advanced Pollution Instrumentation
The OPTI-Sense series of sensors is based on Non-Dispersive Infrared (NDIR) technology. They are designed to precisely measure the absorbance in the infrared spectrum of specialty gases typically found in semiconductor applications. They are very compact and designed with no moving parts, making the OPTI-Sense robust and ideal for continuous in-situ gas monitoring of semiconductor processes.
-
Product
Ship Auxiliary System Monitor
-
A distributed system consisting of a variable number of intelligent measuring units, a central computer located on board a ship, and a remote computer on the shore, with the ability to configure and analyze measured signals via the Internet. Intelligent measuring units are built on the basis of the industrial measuring platform PXI.
-
Product
CO2 Monitor
T5000
-
Although carbon dioxide is invisible and odourless, increased CO2 content in the room leads to fatigue and decreased mental concentration.
-
-
Product
Microbial Contamination Monitors
-
Is an active sampling method that is superior to the usage of settle plates, that additionally creates validated and actionable data.
-
Product
Digital Antenna Monitors
1900 Series
-
There are three different units in the 1900 Series. The basic unit is the Model 1901.This 5 1/4 inch unit contains control/measurement circuitry for up to 12 towers, digital display of all measurements, local operating controls, and an interface to a remote control system. The control/measurement circuitry for each tower is contained in a separate module. The modules plug into the rearof the unit, and may be easily added to an expanding station.
-
-
Product
Power Monitoring Software
-
A digital tool that continuously tracks, analyzes, and manages a facility's electrical system in real-time.
-
Product
Advanced Active/Passing Monitoring System
SQmediator
-
SQmediator® is an advanced active/passive monitoring system engineered to proactively manage the end-to-end performance of a range of network applications, including Voice over IP, IP Videoconferencing, Web and Email. Its multi-service, multi-tenant architecture supports advanced data aggregation, one-click custom dashboards for customers and locations, per-metric service thresholds, real-time alerts, and a web services API for integration with external management systems
-
Product
Automation Monitor
-
The Automation Monitor is a diagnostic system for remote analysis and troubleshooting of semiconductor capital equipment. The monitor is capable of delivering synchronous streams from strategically located video cameras, sound devices and data sources on the equipment.
-
Product
In-situ Wafer Temperature Monitoring
-
CI Semi's family of noncontact temperature monitors (the NTM line), offers high end pyrometry products for the measurement of wafer temperatures during process. CI Semi’s flag ship of the line, the NTM Delta, incorporates real-time, same point emissivity measurement and compensation making it the ideal solution for in situ monitoring for processes such as RTP, CVD and PVD. The NTM family is sold to leading tool manufacturers.
-
Product
PXI Monitored Multiplexer, Dual 32-Channel, 1-Pole
40-619-202
Multiplexer Module
The 40-619-202 is a high density PXI 2 A multiplexer module in dual 32-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
Partial Discharge Detector
APD-ANNUNCIATOR
-
The APD-ANNUNCIATOR is a remote partial discharge detection equipment inside any energized cabinet. The probe is installed in the unit under test, instantly reporting its status. This equipment gives a great benefit because it avoids long term damage to the switching equipment.
-
-
Product
Control & Monitoring Systems
-
Haliatech Control & Monitoring Systems provides organizations with a comprehensive set of solutions designed to enhance operational efficiency and reliability. Through its centralized control, users can manage and operate all devices and systems from a single dashboard, whether on-site or remotely, ensuring streamlined operations across multiple facilities.
-
Product
Surface Quality Monitors
-
PET manufactures and markets non-destructive, non-contact surface contamination and thin film detection models and automated systems (surface quality monitoring system) capable of detecting thin layer contamination, thin films and coating down to the Angstrom level. These systems represent a major breakthrough by providing, for the first time, a quantitative measure of surface cleanliness. As surface cleanliness verification instruments, in a part cleaning environment, these products are capable of validating the cleaning quality of all the part cleaning equipment available in the market. Any of SQM model series is capable of verifying metal contamination; monitoring absence/presence of organic and/or inorganic on virtually on surfaces of all metals. They are, price/performance, the most sufficient product available for testing surface of metals for surface cleanliness. These systems operate in an ambient environment, require no sample preparation or deposit of any agents on the surface. In any parts cleaning environment where the quality and efficiency of part cleaning equipment for removal of surface contamination is highly desired, these systems provide a scientific solution by quantitatively measuring the surface cleanliness. The SQM series has the sensitivity and operational simplicity required to provide fast and cost effective surface evaluation for all metals.
-
Product
PRO Conductivity (EC) Monitor
MC310
-
The Milwaukee MC310 PRO Conductivity (EC) monitor lets you measure EC levels automatically and alerts with an alarm when out of the set point range.
-
Product
Heat Stress Monitors
-
Heat stress management is often viewed as time-consuming and complex. Simplify your heat stress management with TSI’s intuitive QUESTemp° Series Heat Stress Monitors.
