Voltage
The tension of an electromotive force.
-
Product
MCB Instantaneous Trip Test Bench
-
The SCR Elektroniks MCB Instantaneous Trip Test Bench is designed for Testing of MCB to carry out “Test of Instantaneous Tripping and of correct opening of the Contacts” as per IEC: 60898-1:2002 Clause 9.10.2 at rated voltage. This test is carried out with power factor between 0.95 and 1 with the sequence operation being O-t-CO-t-CO-t-CO with timings as specified in 9.12.11.1.
-
Product
High Voltage Surge Testers
HVST
-
The most important features of the surge tester are its ability to test the entire winding insulation system. A high voltage surge generates turn to turn, coil to coil, and phase to phase voltage stress, as well as ground insulation stress. When used as a dielectric test, accurate voltage readings are essential. The HV Surge Tester monitors the voltage directly across the winding under test. This voltage is displayed on an oscilloscope and recorded on the Pass/ Fail LED latch monitor. This voltage will be accurate despite the impedance of the winding being tested. The insulation system can be tested way above the operating voltage because of the brief duration of the applied voltage test pulse. This allows faults to be detected long before they become apparent at operating conditions.
-
Product
High-Power Low-Loss Pulsed Bias Tees
MBT series
-
The MBT-series of bias tees is based on Maury's patented broadband capacitor (US Patent 9,614,267) which simultaneously enables the industry's widest bandwidth, lowest insertion loss and lowest return loss in a coaxial bias tee up to 18 GHz. In addition, its unique design makes it ideal for pulsed applications, including pulsed IV and pulsed load pull characterization, without distorting the voltage and current waveforms.
-
Product
Dual 3U CompactPCI® Subsystem with Two 6-slot Backplanes and Two CompactPCI® Power Modules
cPCIS-2642 Series
Backplane
- Dual 3U CompactPCI® Systems, each with five peripheral card slots and one system slot- 1/1 250 W CompactPCI® Power supplies- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5 V, +3.3 V, and +12 V- PICMG® 2.11 47-pin power interface
-
Product
Module Testing Station
QuickSun® 550CE
-
QuickSun 550CE is certified by TÜV Rheinland and a detailed test report is included with every simulator proving Class A+A+A+ performance with respect to spectrum, irradiance non-uniformity and short term instability (STI). Long term instability (LTI) is also within Class A+ tolerances during the 40 ms long flash pulse. IV characteristics are recorded with an electronic load and proprietary electronics unit which measures voltage, current and irradiance signals when module is swept e.g. from short circuit to open circuit or vice versa.
-
Product
Multimeters
-
Regardless of the job at hand, Klein Tools’ multimeters are designed to quickly measure voltage, current and resistance with ease. Built to withstand jobsite conditions and available in multiple different range options, these multimeters are guaranteed to provide accurate and precise measurements.
-
Product
AC to DC Unregulated Power Supply
-
CEHCO is a specialist in AC to DC Unregulated Power Supply. We can offer the followings:Input power can be single phase (1 PH) or three phase (3 PH)DC output voltage up to 1000 VDC maxDC output current up to 1500 Amps max
-
Product
PXIe-5162, 1.5 GHz, 5 GS/s, 10-Bit PXI, 2 GB mem, Oscilloscope
782622-05
Oscilloscope
PXIe, 1.5 GHz, 5 GS/s, 10-Bit PXI Oscilloscope—The PXIe-5162 high-speed oscilloscope device has two or four channels that sample at up to 5 GS/s with flexible settings for coupling, voltage range, and filtering. PXI Oscilloscopes also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 1.5 GHz of analog bandwidth and flexible measurement configurations.
-
Product
Battery Cell Tester
-
This Centre zero instruments help to read the voltage irrespective of polarity.
-
Product
PXI High Density Digital I/O Module, 32-bit TTL
40-410-001
Digital I/O Module
The 40-410 range of Digital I/O Modules are suitable for operating external devices, such as heavy duty relays (power, RF and high voltage types), solenoids, lamps, or for interfacing with external logic such as a programmable instrument with a BCD interface.
-
Product
Transmission Electron Microscope
TEM
-
Atomic Resolution Electron Microscope offering a maximum accelerating voltage of 300 kV, and equipped with JEOL’s own Cs Correctors. This instrument guarantees an unprecedented STEM-HAADF image resolution of 63 pm.
-
Product
Bench Power Supply, Linear, Adjustable, 1 Output, 0 V, 60 V, 0 A, 2 A
72-2695
-
The 72-2695 from Tenma is a single channel adjustable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +30mV (voltage), ≤0.5% +5mA (current).
-
Product
PCI 2 Amp Multiplexer, Dual 16-Channel, 2-Pole
50-635A-006
Multiplexer Module
The 50-635A-006 is a dual 16-channel, 2-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
1310nm Direct Modulated Optical Transmitter
ONT-8600AF
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Compared with ONT-8600AS, ONT-8600AF has two power supplies and fans as backup to increase its reliability. It is suitable for the areas that have instable voltage, heavy thunder and high temperature.
-
Product
PXIe-5774 , 12-Bit, 6.4 GS/s, DC-Coupled, 2-Channel PXI FlexRIO Digitizer
785646-02
FlexRio Digitizer
The PXIe-5774 provides up to 3 GHz of DC-coupled analog bandwidth and 12 bits of resolution. You can operate the PXIe-5774 in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The voltage ranges are software-selectable and include 200 mV peak-to-peak and 1 V peak-to-peak, with a selectable DC offset. The PXIe-5774 is ideal for time-domain measurements in areas such as scientific instrumentation, medical imaging, and particle physics. The FlexRIO driver includes support for finite acquisition, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
Other Switching Power Supplies
-
PeakTech Prüf- und Messtechnik GmbH
The switching power supply technology used ensures high performance with a small size and low weight. 6 different DC output voltages (3 V / 4.5 V / 6 V / 7.5 V / 9 V and 12 V) can be set using a slider. With the 4 mm pole terminals, you can easily connect single wires but also 4 mm banana plugs. The power cord with an Euro plug is firmly connected to the power supply unit, whereby the device is switched off and on via a rear power switch. This handy power supply fits on every work bench and can be used universally in the hobby area, service or training.
-
Product
External Measurement Instrument Port | Add-On Option to CableEye HVX Series Testers
Item 835
-
Measure 10 GΩ Isolation at 100 V
This new capability is of special interest to customers requiring measurements of extremely high isolation resistance at very low voltages. The HVX-series option may be ordered with new testers or added as an upgrade to previously purchased systems.
-
Product
Ultrasound Pulser ICs And HV Multiplexers
-
ST's Ultrasound Imaging IC Solutions offer a complete range of integrated high-voltage transmitters from quad and octal, to the latest device, the state-of-the art STHV1600 ultrasound pulser IC, to high-voltage multiplexer IC, the STHV64SW, a 64-channel, high voltage analog independent switches. ST’s proprietary BCD6s-SOI and BCD8sSOI process technologies enable the combination of low-voltage CMOS logic, precise analog circuitry, and robust power stages on the same chip, offering unprecedented level of integration.
-
Product
Digital Isolators
-
Silicon Labs' CMOS digital isolator products enable lower cost, smaller size, higher performance, lower power, and more reliable isolated circuits than competing optocoupler solutions. The Si80xx, Si83xx, Si86xx, Si87xx, and Si88xx families of one to six-channel bi- and unidirectional digital isolators support isolation voltage ratings up to 5 kV. With a broad product portfolio, a proven track record of industry innovation and an unwavering commitment to engineering excellence Silicon Labs isolation technology is ready to meet your isolation needs.
-
Product
Electrical Safety Testers
STW-9900 Series
-
* 500VA AC Test Capacity* 240 x 64 Ice Blue Dot Matrix LCD* Manual/Auto Mode* Function Key for Quick Selecting* High Intensity Flash for Caution & Status Indication* Safety Interlock Function* Zero Crossing Turn-on Operation* Zero Crossing Turn-on Operation* True RMS Current Measurement * High Resolution : 1μA for Measuring Current, 2V for Setting Voltage* PWM Switching Amplifier to Enhance the Power Efficiency and Reliable Testing* Max. 100 Memory Block for Test Condition (Step) Setting. And Each Step can be Named Individually* Remote Terminal on the Front Panel for“Start”and“Stop” Control by External* Interface: RS-232C, USB Devise, Signal I/O and GP-IB (Option: OPT.1)
-
Product
V-LISN
-
Measures the unsymmetric disturbance voltage between the two lines L1 and ground or L2 and ground respectively.
-
Product
High Power DC Electronic Load
IT8800 Series
-
IT8800 series has wide power range 150W~10KW, voltage and current measurement speed up to 50KHZ, resolution up to 0.1mV/0.01mA, adjustable measurement current rising speed 0.001A/us~2.5A/us, built-in RS232/GPIB/USB interface. IT8800 series has wide application fields because of its high performance products, it has been applied to LED lighting, aerospace, automotive electronics and other fields.
-
Product
LXI High Voltage Multiplexer Plugin Module
65-231-904-HI
Multiplexer Module
The 65-231-904-HI plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
500 MHz Passive Probe for WaveJet Touch, 10:1, 10 MOhm
PP006D
-
Passive probes are the standard probe provided with most oscilloscopes. Typical passive probes provide a 10:1 attenuation and feature a high input resistance of 10 MΩ. This high input resistance means that passive probes are the ideal tool for low frequency signals since circuit loading at these frequencies is minimized. Passive probes are designed to handle voltages of at least 400V, some as high as 600V. Teledyne LeCroy passive probes feature an attenuation sense pin which tells the oscilloscope to scale the waveforms automatically requiring no user input.
-
Product
Digital Clampmeters
-
AC Current 40A, 400A, 1000A AC Voltage 4V, 40V, 400V, 750V (Auto) (40-500Hz) DC Voltage 4V, 40V, 400V, 1000V (Auto) Resistance 400Ω, 4KΩ, 40KΩ, 400KΩ, 4MΩ, 40MΩ (Auto) Frequency 10.00 Hz, 50.00 Hz, 500.0 Hz, 5.000 KHz, 50.00KHz, 500.0 KHz(Auto) Sp. Functions Data Hold, Audible Continuity, Diode Test, APO Jaw Opening 43mm Max.
-
Product
High voltage Flexible range Regulated DC Power Supplies
PSF-H Series
-
* Main Applications: High-voltage capacitors or relays used for hybrid cars, electric cars, solar power system and high-voltage LED lighting equipment.* 6 times of flexible output range: PSF-800H covers output for several units of conventional type regulated power supplies within 800W ( max voltage 800V, max current 6A. ).* Constant Power Control: CP mode is available in addition to CV and CC modes.* Changeable setting style: Vertical or horizontal setting by 90rotating panel.* Sequence Operation: Stand-alone sequence is available with the insidememory programmed by PC, through the optional control board (IF-60GP, IF-60RU).* Master-slave parallel operation: Possible to increase the output current by master-slave parallel connection of the same model (up to 2 units).* Various functions are available: Output OFF timer, 3-point preset memory, Remote sensing, External analog control, OVP/OCP/OHP protections
-
Product
Modular DC Electronic Load
N3300A Series
-
The new N3300A Series of dc electronic loads is fast, accurate, and ideal for increasing production throughput in high volume dc power supply manufacturing. This series consists of a full rack width (1800 watts max) mainframe and a half rack width (600 watts max) mainframe, and 7 interchangeable electronic load modules. The modules provide a variety of voltage, current and power ratings. New dc connectors for test system configurations are now available on all modules.
-
Product
PXI 2A Multiplexer, 1-Bank, 16-Channel, 8-Pole
40-614C-018
Multiplexer Module
This 1-bank, 16-channel, 8 pole version is part of the 40-614C High Density 2A multiplexer module range that is available in 20 configurations (see Also in this Range link above). All configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PXI 2A Multiplexer 158-Channel 1-Pole
40-611-001
Multiplexer Module
The 40-611 Very High Density multiplexer module is available in 158-Channel 1-Pole or 79-Channel 2-Pole configurations. Both configurations use high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
MOTORIZED TRANSFORMER/RECTIFIER ASSEMBLY, 0-250 VDC, 200 A OUTPUT
18534PS1
-
Input power is 380 VAC, 3 PH, 50 Hz, P/N 18534PS1Output is 0 to 250 VDC, 200 Amp max.Variable Transformer is used to vary the output. SCR controller is not used, as it generates harmonics.Input control is 0 to 3.6 VDCIndoor enclosure, 50"H x 46"W x 36"DOutput voltage and current feedback as 4/20 mA for PLC interface.All input/output connections are inside the enclosure
