VME Backplanes
-
Product
VME Test Extender 3U/400mm J1
111EXT3140-11xx
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
VME Form Factor Extender, 6U, 180mm
111FFE6018-012X
-
The VME form factor extender 6U 180 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
VME Form Factor Extender, 6U, 120mm
111FFE6012-012X
-
The VME form factor extender 6U 120 mm allows to adapt boards for use in the same VMEbus system. It maintain the correct depth dimensions and allow the front panel to be aligned.
-
Product
6U VME I/O & Comm Board
64C3
-
NAI’s 64C3 is a 6U VME multifunction I/O and communication board with six function module slots that can be configured with a variety of I/O and communication functions. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.By eliminating the need for multiple, specialized, single-function boards, this unique design increases packaging density, saves enclosure slots, and reduces power consumption. The 64C3, a low-power/high-performance board, is ideally suited for rugged defense, industrial, and commercial applications.
-
Product
VME PowerPC Single Board Computer
DP-VME-0405
-
The DP-VME-0405 is a high performance VME PowerPC single board computer(SBC) that features the latest PowerPC 7410, SDRAM with error detection and correction and a dedicated L2 cache bus. The board's architecture strikes a balance between high performance processing power, memory and I/O resources. With its vast array of interfaces, the DP-VME-0405 allows the user to perform intensive I/O while permitting rigorous computing. Two industry standard PMC slots enhance the I/O capability, allowing the users to provide program specific features by using commercially available PMC module.
-
Product
2 PICMG® CPU, 10 PCI™, 4 ISA Slots Backplane
HPCI-15S10
Backplane
- Segment: 1- Slots: 2 PICMG® CPU, 10 PCI™, 4 ISA- Supports AT, ATX power supplies- Dimensions: 317 mm x 264.2 mm
-
Product
Backplanes
-
As a preferred vendor to the world''''s largest defense and industrial companies, Atrenne's high-speed backplanes are the go-to choice for organizations delivering high performance and reliability in the harshest defense and industrial computing environments. Available in all of the latest form factors, our backplanes are fully customizable to address the requirements of your specific application. Atrenne offers the industry's largest selection of 10 Gbaud Gen-3 VPX backplanes.
-
Product
VME Extender
VMEEJ1J2
-
VECTOR Electronics and Technology, Inc.
VMEEJ1 Extender on top & VMEEJ2 Extender on Bottomattached with mending plate to create VMEEJ1J2 Extender
-
Product
Type 39 CompacFrame Development Platform, 1 - 4 Slot 3U VPX Power And Ground Backplane
39P01BWX6ZY2VCC0-Tx
-
Elma’s slimline CompacFrame is the next-generation platform designed to accelerate development and test of Plug-In Cards (PICs). The 3U card cage in the platform is tilted upward by 5º for easier card access and accommodates backplanes up to 4 slots.
-
Product
VME
-
Highland Technology is a member of VITA, the VME standards body, and continues to release new technology into the VME market. As other bus architectures come and go, Highland remains confident that VME will maintain its position as the architecture of choice for essential, long life cycle programs.
-
Product
VME SBC
XVR19 6U
-
The XVR19 provides straightforward, cost-effective and low risk upgrades for users of previous XVR products, bringing enhanced processor performance, enhanced storage and improved protection against obsolescence. They will also be attractive for new programs looking to benefit from Abaco’s established and proven VME roadmaps.
-
Product
VME Analog Output Module
DP-VME-2115
-
DP-VME-2115 is an industrial standard 24 channel D/A (Digital to Analog) board. It incorporates most of the features which are demanded in industrial applications. Each Digital to Analog Converter (DAC) is provided with a separate reference voltage selection either from internally generated reference or from the external input. This external input reference signal is passed into the protection circuits before it is fed to any active components. The input protection circuit is designed for ± 25Vp-p input ranges. The DAC output may be unipolar or bipolar and the output is jumper selectable, which is routed to the VME P2 connector, with short circuit protection of upto 30mA.
-
Product
ARINC 429 Test & Simulation Interface for VME
VME-429
-
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
Product
Wiring Analyzers for Cables, Wire Harnesses, Backplanes
CableEye M2Z, M3Z, M4
-
With our cable testers and harness testers, find defective or miswired cables instantly before they damage equipment or waste valuable technician time. CableEye® all-in-one test and cable management systems have a unique, patented graphic wiring display to visually pinpoint problems when wiring errors are detected, and offer under a second pass/fail testing for production environments. Quickly locate intermittent connections and identify their position in the cable.
-
Product
Wallmount Industrial Chassis Supports 10-Slot Backplane
RK-609B
Chassis
- Supports 10 slot PICMG backplane- Two 5.25" and two 3.5" external drive bays, one internal 3.5" drive bay- Upper cover with captive screw- Drive bay with shock and vibration resistant design- Replaceable and easy-to-clean air filter- 12cm cooling fan (85CFM)- Two USB and one PS/2 keyboard connectors on front panel
-
Product
VME Bus Tester
VBT100
-
The VBT100 has been designed to withstand and measure excessive voltages on both signal and power supply pins. This capability allows it to operate in faulty backplanes that could damage other boards. The tester also detects, measures and identifies which signals have excessive voltages so they can be repaired before boards are loaded into a backplane.
-
Product
8-Channel VME Isolated Resistance Simulator
V420
-
The V420 is an 8-channel, isolated, programmable resistance simulator. It uses entirely solid-state simulation to eliminate transient errors associated with relay switching, and provide for monotonic resistance changes. Channels are individually programmable in four resistance ranges, from 5 ohms to 65.5K. Channels can operate from microvolts up to 35V / 50mA. Overload protection and channel error detection are included.
-
Product
VME Master - DAQ and Detector Interface
VX1394
-
The VX1394 board features a radiation hard 4.8 Gbps SERDES ASIC, which, in connection to a rad-hard optical transceiver implements a newer generation optical links for many detector readout systems. The ASIC performs data transmission, trigger distribution and clock forwarding towards the front-end electronics in the crate.
-
Product
cPCI Backplanes
-
CompactPCI bus is compatible, in terms of electrical specification, with the PC world’s PCI bus. The mechanical specifications were adapted to the commonly used Euro-board plug in systems for 19" racks.
-
Product
13-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/13L
-
*1 PICMG, 4 PCI and 8 ISA*Compatible with AX61400, AX6145, and AX6156LE*Supports both AT and ATX power supply
-
Product
System Synchronizer and Distribution Board - VME
Model 6891
-
Model 6891 System Synchronizer and Distribution Board synchronizes multiple Pentek I/O modules within a system. It enables synchronous sampling and timing for a wide range of multichannel highspeed data acquisition, DSP and software radio applications
-
Product
VME64x VITA 1.7 Backplanes
-
Atrenne VME64x VITA 1.7 backplanes comply with ANSI/VITA 5.1, include a 12-layer low noise striplinedesign with outside layers, which incorporates a chassis ground EMI shield and are available in customer configurations.
-
Product
3U CompactPCI® Subsystem with 8-Slot Backplane and 400 W ATX Power Supply
cPCIS-2630 Series
Backplane
- 400 W ATX Power supply- 3U CompactPCI® backplane with seven peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports rear I/O backplane with P2 connectors for cPCI 50mm/80mm depth RTMs- Temperature, voltage, and fan monitoring LEDs
-
Product
Other Eurocard Backplanes
-
OpenVPX, CompactPCI, VME, and VME64x are open standard backplane architectures commonly used in Eurocard systems. (For OpenVPX products, see the Pixus OpenVPX section.) Pixus has a wide range of CompactPCI, VME, VME64x, and other backplanes available off-the-shelf.
