Insulation Resistance Testers
-
product
Surge/Impulse Testers
specifically designed to perform the Input Test on PV Panels in accordance with IEC 61730-2, Para. 10.5.3. The output is in accordance with the published waveform from 800-10000V peak (open circuit).
-
product
Digital Insulation Tester
DIT-1020
Laxtronics Instruments & Controls Pvt. Ltd
Digital insulation tester Model No: DIT-1020 is designed to carry out electrical insulation measurement in delicate or sensitive electronic sensors, transducers, modules and assemblies with test voltage of 100 Volts DC, its short circuit current is less than 500uA.
-
product
Digital (1kV below) Insulation Tester
1651 IN
Standard Electric Works Co., Ltd
Microprocessor-controlled. ACV auto-detection function on 3 insulation ranges (250/500/1000V) and low Ω ragne before pressing the TEST button. 68 x 34mm large LCD display. 3½ digital LCD (2000 counts) a LCD indicated instrument for insulation(MΩ), continuity (Ω) and AC voltage. Three insulation test voltages(DC V) : 250V, 500V, 1000V. Auto ranging. Auto power off function. Auto data hold function. Rel function (ohm only). Continuity buzzer. External AC voltage warning. Automatic circuit discharge. BS 16th edition.
-
product
Three Phase Tester
4200
Peaceful Thriving Enterprise Co Ltd
*Fast and accurate measurement.*Portable and compact design, easy to carry.*Efficient, effective, reliable, easy and safe to use.*Two function in one unit. Including open phase and phase sequence.*This is idea for installing conveyor lines, pump systems and interconnected drivers.*Indicate phase orientation (clockwise or counter-clockwise) and whether each of three phases is live.
-
product
Deadweight Testers
AMETEK Sensors, Test & Calibration
We provide the world’s only ball-type deadweight testers, where the ball and weights float on a thin film of air, which is virtually frictionless. This design eliminates the necessity to rotate the weights during testing, and allows the user to concentrate on the instrument itself. Our testers are engineered to offer user-friendly, safe operation, in the field, or in a lab. Both pneumatic and hydraulic testers are available.
-
product
Distribution Transformer Tester
DOC-2000™
The DOC-2000™ is a test instrument designed for distribution networks transformers up to 167KVA. It can determine the presence of short circuits or an open circuit in the distribution transformer primary winding & also short circuits on the secondary winding. The DOC-2000™ is designed to be operated from an arial device or from the ground at the end of a hot stick without disconnecting the transformer’s secondary windings.
-
product
Memory Burn-In Tester
H5620/H5620ES
As Server and Mobile applications have mainly led the Memory and market has also entered a super cycle that has completely withdrawn from the previous silicon cycle.Memory capacitance will continue to rise as the application of data processing and mobile communication occurs—however, revenue will not grow as ASP goes down. Suppliers need to reduce test costs and increase profits.H5620 contributes to reduction of test cost by integrating the test process of DRAM Burn-in and Core Test. This hybrid memory test solution solves the challenge of reducing test costs while increasing test efficiency in the expanding DRAM market.
-
product
Noise And Vibration Tester
In a miniaturized motor, even the slightest rumbling sound that occurs during rotation can be a cause for failure.
-
product
Oil BDV Tester
Weshine Electric Manufacturing Co., Ltd
Insulating oil in electrical power apparatus serves two primary roles, as an insulator and a coolant. As an insulating liquid, oil’s most important property is a high dielectric strength and as a cooling liquid, a low viscosity is paramount. The principal nemeses of insulating oil are oxidation, contamination (particularly moisture, which tends to lower the dielectric properties of insulating oil), and excessive temperature.
-
product
Alternator/Battery Load Tester
6031
• Tests for defective alternator diodes including GM trio test• Performs complete battery test• 125 Amp load checks state of charge • Searches for excess starter current and alternator/regulator output voltage• Includes test lead set (610271)• Made in USA of US and Global Components
-
product
S-GW Functional Tester
The LTE SGW Functional Tester provides a wrap-around test solution for the Serving Gateway by emulating all the LTE network elements surrounding the SGW (System Under Test). The S-GW Functional Tester emulates an LTE eNodeB and other Core Network entities such as the MME, P-GW, S-GW, RNC and SGSN. It tests the S1-u, S11, S5/S8 , S12 and S4 interfaces of the S-GW.
-
product
Battery Tester
Changzhou Applent Instruments Inc.
Is an electronic device intended for testing the state of an electric battery, going from a simple device for testing the charge actually present in the cells and/or its voltage output, to a more comprehensive testing of the battery's condition, namely its capacity for accumulating charge and any possible flaws affecting the battery's performance and security.
-
product
Shoe Heat Insulation Tester
UI-FT08
Shoe Heat Insulation Tester – Thermal Insulation Tester is used to test shoe heat insulation / thermal insulation against hot performance. Place the shoe in sandbath and the footwear shall contact with the plate(forepart and the heel) in certain temperature for a given period. Then to measure the temperature increase inside of the shoe. The contact temperature and time is specified in production standard.
-
product
Digital RCD Testers
Used to detect whether the RCD in the circuit can be triggered normally.
-
product
Multifunction Installation Tester
COMBIG2
Multifunction installation tester with colour touchscreen display and WiFi compatible with HTANALYSIS™
-
product
Gas Permeability Testers
Gas Permeability Tester (Gas Transmission Rate Tester) is based on the differential pressure method and is professionally applicable to the determination of gas transmission rate of plastic films, composite films, high barrier materials, sheeting, metal foils, rubber, tires and permeable membrane.
-
product
Portable Ethernet Testers
Portable Ethernet Testers are widely used to test the performance, function, and quality of Ethernet and IP network systems by generating and validating traffic patterns.
-
product
Cable Transmission Tester
SIGNALTEK CT
If you install or maintain data cabling, SignalTEK CT allows you to generate PDF test reports that prove installed links run at Gigabit Ethernet transmission rates.
-
product
Blanket Flammability Tester
TF316
TESTEX Testing Equipment Systems Ltd.
Blanket Flammability Tester, to determine the ignition resistance property of blanket fabrics and surface flame spread performance of fabric. A standardized flame is applied to the surface of specimen for a special time under controlled conditions, and burning, changing, or discoloration of a paper monitor is noted to classify flammability of tested fabric.
-
product
Insulation Tester
AD-2050
Measuring voltage control during measurement, Insulation measurement up to 400 G W. Elimination of trough resistance insulation. 3 connectors measurement method, Autoranging, Auto-Discharge facility safely discharges the connected circuit after a test, 5 minutes, 1 minute at will shorter measurement,
-
product
Waterproof Dual Range Tester
ECTestr 11
User-Replaceable Sensor - Replace the sensors yourself. Sensors lasts longer with element made of SS316 stainless steel and sensor casing made of VALOX®
-
product
Cable Tester
The Cable Test System is a perfect example of a special solution built on existing DapTechnology building blocks. The system, which was developed with the cooperation of a key A&D cable harness supplier, replaces a cable test system with proven FireSpy Technology.
-
product
Burn-In Board Tester
Focus-275
Focus275 is a tester for burn-in board.It can improve reliability of burn-in board by inspecting boards for burn-in test by Focus275 regularlyBoth short open test and component test can be done by sending electric signals for special socket contactor and edge part.
-
product
Type T Deadweight Tester
AMETEK Sensors, Test & Calibration
The Type T tester is a dead weight tester that offers laboratory accuracy in an instrument designed to withstand an industrial environment or daily stresses of a manufacturing environment. Each tester features a re-entrant type measuring piston and cylinder assembly.
-
product
Brush or Sponge Pilling Tester
TESTEX Testing Equipment Systems Ltd.
Brush or Sponge Pilling Tester, To determine the pilling propensity and simulate normal wear of knitted and woven fabircs used in apparel and automotive interiors by brush and/or sponging specimens together in a circular motion to form pills. Brush or Sponge Pilling Tester complies with ASTM D3511, FORD BN 12-4, FORD BN 108-03, etc.
-
product
Motor Stator Tester
DZ901
Shanghai Aoboor Electric Co., Ltd.
Applicable to precision electrical properties test of stators of y-type three-ohase motors, single-phase motors, hub generators, brushless motors and servo motors.
-
product
Harmonics and Flicker Testers
complied standards and features of the KHA1000 (dedicated for single phase), is equipped for the harmonic and flicker compliance test exceeding 16A of the single-phase and three-phase equipment. With this unit alone, you can take highly accurate simultaneous three-phase measurements up to 40A/phase*.
-
product
Function Tester
Test device for functional testing of defibrillators, external pacemakers and ECG simulation.
-
product
Multi-channel Resistance Meter
Changzhou Applent Instruments Inc.
Can scan and test 10 channels of resistance and can set a comparator for each channel. Its temperature compensation function can adapt different testing requirements. It can be applied to automation equipment.
-
product
Ferroelectric Tester
Premier II
The Precision Premier II, is one of Radiant's most advanced test systems. The Premier II has the large envelope in terms of frequency response, voltage range, and accuracy of any ferroelectric tester in the world. Vision Software is provided with the Premier II Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choice from.
