Modbus
communications protocol for sharing data between controllers.
See Also: Communication Protocol, Near Field Communications, Data Communications, Modbus RTU
-
Product
Self-reclosing Overcurrent And Residual Current Protection
-
Wide range of solutions to guarantee personnel safety as well as maximum service continuity in the event of a ground current or breaker trip, with automatic reconnection of the installation. Available with RS-485 communications (Modbus RTU) and remote control inputs/outputs.
-
Product
Gas & Flame Detection System
Syntel
-
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
Product
RS485 Remote Display Indicator
CS1-8
-
CS1-8 has been designed for remote display by RS485 (Modbus RTU Mode) interface.
-
Product
Wireless Temperature Meter
WTM-100
-
●Measure accuracy:±1℃●Display range: -50.0~150.0℃●RS485 Modbus RTU communication port●Up to 12 channels wireless sensor connection●High stability and low cost●CE Approved
-
Product
Modbus/TCP Gateway
MODG-100
-
MODG-100 is a Modbus/TCP to Modbus RTU gateway. Itfeatures one serial port which can be configured as either RS-232, RS-485 or RS-422 and an Ethernet port. It can be mounted on a DIN rail.
-
Product
CAS Modbus Scanner
-
CAS Modbus Scanner is a utility to retrieve coils, inputs, holding registers, and input registers from a Modbus enabled device. Values retrieved from the device can be viewed in many different formats including Binary, HEX, Uint16, Int16, Uint32, Int32, and Float32. This utility can also discover Modbus devices on your network if you do not know their address. It works by testing every address, function, length, offset to check for exceptions or responses.
-
Product
RTD Temperature Indicator
CM2-TR
-
CM2-TR RTD Temperature Indicator has been designed in simple operation and 4 digital 20mm LED display with economic cost.They are can be programmed by buttons that are hidden in front panel.They are also available to option relay output and an analog output or RS485 (Modbus RTU Mode) communication.
-
Product
Wireless Modbus Sensors
-
Wireless Modbus Sensors & Condition Monitoring – The Best of 2 Worlds! Combining Phantom Wireless Sensors with an Industry Standard such as Modbus! The best in Vibration monitoring equipment!!
-
Product
Monitors
-
Whether you need a local display, alarm and shutdown capability, data recording, and the ability to communicate using Modbus over Ethernet TCP/IP; or you need to trend waveform and transient data to provide a predictive look at your machine’s condition, Metrix has a solution to meet your machinery monitoring requirements.
-
Product
Energy Analyser
Duca-LCD96
-
Energy Analyser for front-panel mounting 96x96, for Single-Phase/Three-Phase systems with 5-lines wide LCD screen, Co-generation Energy measurement and "Wide Range" Power Supply (24 - 240 Vac/dc). Optional RS485 serial line interface, Modbus, Profibus, Ethernet, Analog interface 4-20mA, pulse readings.
-
Product
4 Digit Voltage/Current Meter
CM1-VA
-
CM1 series Indicator has been designed in simple function and 4 digital 20.0mm LED displays with economic cost.They can be programmed by tact switches that are hidden in backside of front bezel.They are also available option of 2 Relay outputs, 1 Analog output or 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of industrial applications.
-
Product
Load Cell Transmitter
MODEL SST-HV
-
The SST-HV is a Plug & Play Smart TEDS IEEE 1451.4 compliant Transmitter. Just plug in a TEDS compatible Load Cell or Torque Sensor and the SST-HV will automatically self-calibrate. When used with a non-TEDS Load Cell or Torque Sensor, the SST-LV Transmitter is easily programmed using a PC with an RS232 port and Instrument Setup (IS) software, which provides a graphical user interface. The SST-HV may be powered from 95-240 Vac ±10%. The SST-HV has an Isolated transducer excitation output that is selectable between 5Vdc or 10Vdc. There are Dual solid state relays and an Isolated 4-20 mA, 0-20 mA or 0-10V analog output. There are three Isolated serial data transmitter output ( RS232 , Half-duplex RS485, full-duplex RS485 ) and three serial protocols that are software selectable (Modbus RTU, Modbus ASCII and Custom ASCII). Isolation to 250V rms is provided for power, signal input, analog output, relay outputs, and communications. Isolation adds safety and avoids possible ground loops. The transducer excitation output is isolated to 50V from signal ground.
-
Product
Electromagnetic Water Meter
WATERFLUX 3070
-
WATERFLUX 3070 is the first battery powered water meter for the drinking water industry that is capable of measuring flow, pressure and temperature with one sensor. Communication via Modbus RTU or pulse.
-
Product
Economic Type Temperature Indicator
CS1-T
-
CS1-T economic type Temperature Indicator has been designed with high accuracy measurement, display and communication of Thermocouple or Pt100Ω.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
Wireless Air Quality Sensors
AQW Series
-
AQW series was designed for air quality measure, such as PM2.5, Ch20, CO2, temperature and humidity. Use high-precision sensor to ensure long-term stability and reliability of the instrument.Panel with large LCD display, easy to read the measuring value.And also have 4 LED indicator to indicate air quality status and device running.AQW series communication port is WiFi, it’s convenient for data collect, support Modbus TCP protocol, and others cloud protocol.
-
Product
PROFINET Gateways
-
The PROFINET Fieldbus gateways provide seamless communication between Modbus RTU/TCP and PROFINET communication protocols.
-
Product
High-power DC Electronic Load (6kW~60kW)
FT68200A/AL/E Series
-
Shenzhen FaithTech Technology Co., Ltd.
FT68200 series high performance high-power DC electronic load provides three voltage ranges 150 V/600 V/1200 V, maximum current 2400 A per single unit, stand-alone power from 4 kW to 60 kW, expandable up to 600 kW, 10000A by master-slave paralleling. Ultra-high power density, 6kW is with only 4U height. Wider operating region, faster dynamic frequency, as well as transient mode, OCP/OPP test, sequence test, automatic test and battery discharge test functions greatly enhances its test strength and expands application coverage. Furthermore, two times instantaneous overpower loading capability can effectively reduces user’s test cost. Built-in standard RS232, RS485, LAN, USB (serial), optional GPIB and CAN interface, supports SCPI, ModBus RTU and CANopen protocol, which facilitates system integrators. FT68200 series has full protection functions, which can be applied to power battery discharge, DC charging station, charging piles, charging pile modules, vehicle On Board chargers (OBC), high-power switching power supplies, power electronics and other power electronics products.
-
Product
Modbus Master TCP/IP Component for .NET
WSMBT
-
WSMBT is a powerful and simple to use .Net component that makes it easy to access data from a Modbus slave device connected to the PC's Ethernet network. Simply drop the component on your form and talk to your device with your VB.NET, C# or Managed C++.
-
Product
Process Indicator
CS2-PR
-
CS2-PR Process Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~10V and 4(0) ~20mA with square root function.They are also build in 4 Relay outputs, 3 External Control Inputs, 1 Analogue output and 1 RS485 (Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission and communication for a wide range of industrial applications.
-
Product
4 2/3 Strain Gage Meter (1/32 DIN)
CS3-SG
-
CS3-SG Strain Gauge Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV as like as Load Cell or Strain Gauge.The meter supports Field Calibration function. It can be calibrated with sensor(Load Cell/Strain Gauge) to meet machinery structure.They are also building in 2 Relay outputs, 1 External Control Input, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
Open Master/Slave Application Protoco
Modbus TCP
-
Modbus-TCP means that the Modbus protocol is used on top of Ethernet-TCP/IP. Modbus-TCP is an open Industrial Ethernet network which has been specified by the Modbus-IDA User Organization in co-operation with the Internet Engeneering Task Force (IETF) as an RFC Internet standard.
-
Product
Industrial Automation
-
PLANET Industrial Automation solution is designed to help set up IP networking in the areas of Industrial 4.0 and IoT using the serial port connection. Our Industrial Automation product line includes RS232/RS422/RS485 Serial Device Servers, Modbus Gateways, EtherCAT Slave I/O Modules and Serial over Cellular Gateways, each of which enables to convert and transform useful data for further analysis to optimize factory operation and management.
-
Product
Networked Absolute Inclinometer
T7
-
The T7 is available in several interface and protocol options. The physical interface can be RS232, RS485 or US Digital's CAN (Controller Area Network). The protocol can be either US Digital's serial protocol or Modbus RTU. The RS232 version supports a single T7 with up to 100 ft of cable. For users that need longer cable lengths or multiple T7s on a single bus, the RS485 or US Digital CAN (Controller Area Network) version can be used. The USD-CAN protocol allows a network of up to sixty-four T7s to be connected to a single host. Power for each T7 is supplied over the CAN network cable. The host accesses the USD-CAN T7s through US Digital's low cost CANA-232/CANA-485 adapter module. This module allows the host to access each T7 on the network using simple, easy serial port commands, just like the RS232 version. The RS485 version supports up to 32 T7s on the bus.
-
Product
Process Indicator
CS1-PR
-
CS1-PR economic type Process Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~10V and 4(0)~20mA.They are also available 1 option of 1 Relay outputs, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of industrial applications.
-
Product
Industrial Gas Detectors
-
Seitron designs and manufactures detectors for methane, LPG, gasoline vapours and carbon monoxide (CO) for commercial and process industry use. Our detectors provide three communication protocols 4..20mA, Modbus and S-Bus (a proprietary protocol derived from Modbus). You can also choose between two types of housings: polycarbonate for industrial use or ATEX-certified for the installation of detectors in ATEX-classified areas.
-
Product
Multi Interface USB Adapter
SUB-20
-
SUB-20 is a versatile and efficient bridge device providing simple interconnect between PC (USB host) and different HW devices and systems via popular interfaces such as I2C, SPI, MDIO, RS232, RS485, SMBus, ModBus, IR and others. It is also a full "any to any" converter between all supported interfaces and I/O features. SUB-20 is a powerful I/O controller with 32 GPIO, 8 Analog Inputs, PWM Outputs, Edge DEtectors, LCD, Leds and push buttons.SUB-20 system includes SW package containing driver, API Library, GUI and Command Line based applications, C,C++,C#,VB.net, MATLAB, LabView sample code and documentation. SUB-20 can be used with PC 64/32 bit running Windows 2000/XP/Vista/Win7/Win8, MacOS, Unix/Linux and DOS.Working with SUB-20 does not require deep knowledge of low layers of the specific interface. All you need to do is to call right API function at the right place. And this is really very easy as API functions are well documented and "exampled". API set is relatively small but comprehensive.SUB-20 is equipped with status Leds, optional LCD and buttons. All this guarantee fast and comfortable development, field debugging and maintenance of applications including option of standalone operation.
-
Product
Multifunctional Meter
CPM-20
-
CPM-20 multifunction power meter provide high accuracy single phase and three-phase measuring and displaying, energy accumulating, power quality analysis, and data communication.It provides maximum/minimum records for power usage and power demand parameters.Hardware standard built in a RS485 Modbus communication port.FCC and CE Approved
-
Product
Pyranometer products
-
Hukseflux Thermal Sensors B.V.
Hukseflux is a leading manufacturer, both in technology and market share, of pyranometers, pyrheliometers, pyrgeometers, net radiometers and albedometers.We produce a complete range of solar and longwave radiation sensors, compliant with the latest ISO, IEC and WMO standards. Each Hukseflux pyranometer is classified as ISO 9060 secondary standard, first class, or second class, and offers the best measurement accuracy in its class. Pyranometer output is analogue and/or digital (Modbus over RS-485/TTL).
-
Product
Serial Device Servers
-
Advantech''s serial device servers, Modbus gateways, and USB Device Server are easy to install and configure, support wired and wireless networking and provide various operation modes to satisfy rigorous industrial automation needs.
-
Product
Voltage/Current Indicator
CS3-VA
-
CS3-VA Voltage/Current Indicator has been designed in miniature size(24 x 48mm), and provide high accuracy measurement, display and communication of 0~300V or 0~20mA for DC/AC(average).They are also to build 2 Relay outputs, 1 External Control Input, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication.
