Filter Results By:
Products
Applications
Manufacturers
Power Line
overhead or buried cable carrying electric power.
- Pickering Interfaces Inc.
product
PXI 16 Amp Power Multiplexer, Single 8-Channel 1-Pole
40-662A-013
The 40-662A-013 is a single 8-channel, 1-pole MUX and is part of our range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer.
-
product
Power Monitor, AC-Powered, Field Adjustable
YMA/YQA
NAI's YMA and YQA Power Monitors are used to monitor voltage, frequency, and phase characteristics of single- or three-phase power lines. This allows normal operation of system loads when the power-line characteristics are within predetermined limits.High and low voltage and frequency limits, and "pick-up" and "drop-out" time delay are field-adjustable using potentiometers. These power monitors are ideally suited for rugged defense and industrial applications.
-
product
Power Induction Tester
MIG-ITU-K44
The MIG-ITU-K44 is designed for power induction testing at line frequencies of 50 and 60Hz. Power induction tests need only be performed at the frequencies of the public power supply or railway power of the country of application. Basic and enhanced level tests can be performed according to ITU-T K44.
-
product
Power Cable Fault Locator
TM500
TM500 Power Cable Fault Locator adopts international advanced electronic testing technologies and SCM technology, and combines low-voltage pulse reflection and pulse current testing methods, is suitable for the precise range finding of power cable high resistance, flashover, disconnection, and low resistance. Low-voltage pulse reflection method applies to test the range of the low resistance and broken line, and the length and wave velocity of various cables. Pulse current testing method can be divided into breakthrough high-voltage flashover and DC high-voltage flashover for the high resistance and flashover cable fault finding.
-
product
Power Line Meter
The Line EMI Meter measures electromagnetic interference in a single-phase AC power line. It plugs into a wall outlet (mains socket) and requires no battery. It immediately displays total line noise in millivolts (range 1999 mV, resolution 1 mV) in the frequency range 10 KHz 10 MHz (the frequency limits at which sensitivity is of the maximum sensitivity). A speaker plays the sound of the EMI, amplitude demodulated, in order to identify the EMI source (such as an AM or shortwave radio station vs. a motor vs. an electric arc).
-
product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281B
The Keysight P281B adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
Vibration Meter
Shenzhen Graigar Technology Co.,Ltd.
Vibration meter (also called vibration severity) uses Piezoelectric Acceleration Transducer transfer the vibration signal in to electrical signal, analyze the input signals, and show the Acceleration, speed, shift of the vibration. It is widely used in the lines of Power, petrochemical, machinery manufacturing, metallurgy, vehicles, etc.
-
product
Saluki SEL8 Series Programmable DC Electronic Load (up to 200KW)
The new SEL8 series programmable DC electronic load is a new generation product designed by Saluki Technology. Incorporating high-performance chips, the SEL8 series delivers high speed and high accuracy with a resolution of 1mV and 1mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs).SEL8 series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar cell and fuel cell etc. test and measurement applications.* Customization available upon request
-
product
Power Transformer
We are amongst the leading names in the industry, offering wide range of Power Transformer that are technically advanced in nature and have high strength. Our entire product line is dimensionally accurate in nature and requires low maintenance cost. They are thermostatically balanced in nature AND are easy to install.
-
product
ACDC
EC Series
The EC Series of line operated power supplies features near constant efficiency over theentire rated input voltage range. These electrically identical families employ a highly efficient, closed loop ripple regulation circuit, which contains a low pass filter. Each stage, transformer, filter and regulator is engineered for maximum efficiency.
-
product
Graphical Power Quality Analyzer
PS5000
The PowerSight PS5000 Power Quality Analyzer is the premier member of the PowerSight line of compact, versatile, easy-to-use power quality analyzers. It provides the Most Efficient and Error Free Solution for doing Power Studies.The full color display eliminates the need for laptops to see waveforms and logs. Phasor diagrams provide quick verification of connections.The visual presentation of potential errors in connections and settings, via SureStart, minimizes the risk that the data will be incorrect at the end of the study.The graphical user interface allows easy changing of trigger thresholds.The large screen and “soft keys” allow quickly viewing all measurements of interest quickly.
-
product
Time Measurement Equipment
TimeSpy
The TimeSpy precisely measures the time accuracy of a wide range of inputs (such as: NTP, IRIG B, 1PPS, and ASCII) against an internal precision GPS-controlled oscillator, displayed on the large, full color windows-based touch screen. The TimeSpy can precisely measure the time error at the point of use for systems where time is distributed over large distances. The TimeSpy can also measure free-running clocks and timing systems which are synchronized from untraceable sources, such as television and radio broadcasts, electrical power lines and the internet.
-
product
Hair Scan Portable Yarn Hairiness Monitor
Y103C
For monitoring the quality of spun yarn or detecting broken filaments. The portable battery-powered unit uses an infrared detecting head, while low power circuitry ensures a long battery life, typically 10 hours. A two line intelligent display (LCD) shows the measurement time (seconds) and count. If the batteries are low on charge, a message will appear requesting the batteries to be charged.
-
product
Air Core Test Lab Reactors
Test Laboratory Reactors are designed for high voltage and high power test laboratories. They are designed to withstand the most extreme electrical service conditions during test periods. Design techniques are implemented in accordance with the most demanding service conditions. These reactors are used for various purposes in test laboratories such as current limiting and synthetic testing of circuit breakers, capacitor testing, artificial line simulation etc.
-
product
Triplexers
*Combine three bands to a common line*Multiple broadband configurations, including AWS & WCS*High power handling with low IM and insertion lossAISG 2.0 compatible
-
product
Unequal Split Power Tappers
Pasternack unequal split power tapper product designs are also known as unequal couplers, power dividers or splitters, cross band couplers and signal samplers. Many of our unequal couplers / tapper series are RoHS and REACH compliant. Unequal RF tappers from Pasternack are available with 4.1/9.5, 4.3-10, 7/16 DIN and Type N connector options. These unequal split power tapper components for RF are manufactured to precise specifications required for accurate specified values listed for each product. Unequal split tapper products work with high power of up to 300 watts depending on style. Frequency ratings for unequal power splitter line are wide band components with a 380 MHz to 6 GHz frequency range, based on model selected. Pasternack RF power tappers in unequal design can be ordered with various directivity (dB) values of 4.8dB, 5dB, 6dB, 7dB, 8dB, 9dB, 10dB, 11dB, 12dB, 13dB, 15dB, 16dB, 20dB, 30dB depending on model. As with our other over 40,000 RF, microwave and millimeter wave components from Pasternack, this unequal split power tapper/coupler/divider series for RF is in-stock. These unequal split power tappers are not just in stock, but they will also ship the same-day are they are purchased.
-
product
Socket Tester with RCD Tripping
Shanghai Beha Electronics Co., Ltd.
*Mains wiring polarity check.*ELCB/RCD testing.*Measuring ear for line current.*Measuring ear for leakage current.*Helps calculate insulation resistance.*Helps calculate power consumption.*Helps fault finding of standing earth fault.*Fused main adapter.*Appliance testing (with the ad of a clamp meter).
-
product
Digital I/O Board
3512
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
product
Digital Milliohm Meter
4538 mO
Standard Electric Works Co., Ltd
● 4-Wire method for mΩ measurement.● Measures down to 100µΩ (0.1mΩ).● Maximum resolution of 100µΩ.● 4 Lines × 20 Characters large LCD.● 200 measurement results can be saved in the memory and recalled on the display. ● Auto power off.● Data hold function.● MAX/MIN function.● Power source: 1.5V "C" battery × 8● Long battery life and stable power. ● Low battery indication.
-
product
XRF Systems
OEM Solutions
Amptek offers a complete line of OEM detectors, preamplifiers, digital processors, and power supplies, and can work with you to help develop custom solutions unique to your needs. We provide established and emerging OEM customers a fast track to the market with our modular systems that will meet current needs, while being flexible enough to adapt to your product roadmap. The below options are typical configurations. Please contact us for custom solutions.
-
product
Radiation (EMF, Nuclear, RF)
Sper Scientific radiation meters measure EMF, Nuclear, and Microwave radiation levels. Whether you are, measuring the RF strength of Wi-Fi and LAN network, or the electromagnetic field emissions from electrical power lines and transmission equipment, computers, HVAC, audio/video, and other electrical appliances. Our meters are small and light enough to go anywhere, yet sensitive enough to detect minuscule amounts of gamma, beta or X-rays.
-
product
Color Bar Generator
BL-CBG402-01N
The BL-CBG402 is a small (2 inch x 2 inch) RGBS Color Bar Generator designed for embedded and systems applications. It produces a split field SMPTE style color bar pattern and has either an external composite sync line of optional sync-on-green (set with an optional on-board DIP switch) Video timing is NTSC/EIA 60Hz field rate. The BL-SBG402 operates from a +5V regulated power source.
-
product
Expandable Fanless Embedded Computers
ADLINK's MXC product line provides fanless embedded computers for high-performance embedded solutions. Leading the field, high-performance computing power combines with PCI/PCIe high-speed expansion slots in a compact enclosure fully enabling integration of a variety of applications.
-
product
Bench Power Supply, Linear, Programmable, 1 Output, 0 V, 30 V, 0 A, 5 A
72-2710
The 72-2710 from Tenma is a single channel programmable bench top power supply. It is a digitally controlled industrial grade power supply with load for a long time. This compact design power supply has intelligent temperature controlled fan, low noise and low ripple. It also features knob lock function to avoid improper operation. This power supply has load regulation ≤0.01% +2mV (voltage), ≤0.1% +5mA (current) and line regulation of ≤0.01% +3mV (voltage), ≤0.1% +3mA (current). The setting accuracy (25°C ±5°C) is ≤0.5% +20mV (voltage), ≤0.5% +10mA (current).
-
product
Analog Panel Meter
Hoyt Electrical Instrument Works Inc.
Hoyt supplies a complete line of panel meters for several vertical markets (Switchboard, Audio, Power, Marine, and Power Generation). The meter movements can be pivot & jewel or taut band. So whether you are looking for AC/DC amps, volts, frequency, elapsed time, watts, vars, power factor, or any other measurement parameter we have the meter.
-
product
USB Virtual Oscilloscope
DSO-2250
USB2.0 interface, no external power source required, easy to use. be suitable for computer，product line maintenance，be used easily on business. High performance . 23 measurement functions, PASS/FAIL Check, be suitable for technical application. Waveform average, persistence, intensity, invert, addition, subtraction, multiplication, division, X-Y plot. Save waveform in the following: text file, jpg/bmp graphic file, MS excel/word file. FFT One computer can connect many DSO, extend channel easily. Labview\VB\VC\Delphi\C++Build Second Design instance. Operating System: Windows98,Windows Me, Windows NT, Windows 2000, Windows XP ,VISTA Dimensions (mm):190(L) x100(W) x35(H), be carried easily.
-
product
Incremental Encoders
Versatile, compact and flexible – Incremental encodersIncremental encoders are used when retention of absolute position upon power loss is not required. These encoders provide information about the position, angle and number of revolutions. The number of lines per revolution determines the resolution. The current position can be determined by counting these pulses from a reference point. Upon activating the machine, a reference run to the reference point is required to determine the absolute position of the encoder.
-
product
C-Band Single Channel Line Amplifier EDFA (SLA)
HSA4200 (With SNMP)
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai HSA4200 series is a line EDFA designed specifically for single wavelength optic transmission system. It is installed in the middle of the transmission line, replacing the traditional relay station, to compensate the optical power loss in the line and extend the signal transmission distance.
-
product
Modular Designed CAMAC
CAMAC CERN-CE 300W
WIENER offers a line of modular designed CAMAC crates compliant with ESONE and CERN standards. This CAMAC crates series is configured with 300W linear regulated, low noise plug-in power supplies.
-
product
Step-Tunable Laser Source, High Power and Low SSE, Basic Line
N7779C
The new N7779C basic line step-tunable laser source is ideal for cost-effective testing of broadband optical devices. It can also serve as a highly stable, tunable local oscillator for receiver testing or transmission experiments.
-
product
Level System
Universal II
The Universal II level transmitter offers increased reliability, low maintenance and an intrinsically safe design for dependable level measurements in all kinds of process liquids, slurries, granulars and interfaces.Universal IIThe Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.When powered from an approved source this level transmitter can be made intrinsically safe. Its rugged contruction resists corrosion and abraision. The no moving parts design eliminates break downs.The Universal II level transmitter utilizes RF Admittance technology with manual calibration and a 4 – 20 mA output signal. The patented Cote-Shield circuitry ensures accuracy and reliability regardless of product build-up on the level transmitter.This level system is unaffected by changes in the process material density, pressure, or temperature variations.
