Data Acquisition Software
Data acquisition software is designed to record, store, present and analyze data collected from sensors and other digital devices. (globalspec.com)
-
Product
32-CH 16-Bit Up to 250 kS/s Multi-Function DAQ Cards
PCI-9114 Series
Data Acquisition Module
ADLINK PCI-9114 series are 32-CH, 16-bit, high resolution multi-function DAQ Cards. The PCI-9114 device features flexible configurations on analog input. The devices are divided into 2 kinds: normal gain version and high gain version. Both versions provide 4 programmable input ranges for bipolar and unipolar inputs. The A/D on the PCI-9114DG device features a sampling rate of 100 kS/s with resolution at 16 bits, while PCI-9114A-DG/HG device features a sampling rate of up to 250kS/s with resolution at 16 bits. The device supports automatic analog input scanning, and offers a differential mode for 8-CH analog inputs and maximum noise elimination, as well as single-ended modes for 16- CH analog inputs. The PCI-9114 also features 1-CH 16-bit general purpose timer/counter, 16-CH TTL isolated digital inputs and 16-CH TTL isolated digital outputs. ADLINK PCI-9114 delivers cost-effective and reliable data acquisition capabilities and is ideal for a broad variety of applications.
-
Product
16-CH 16-Bit 250 kS/s Low-Cost Multi-Function DAQ PCI Express Cards
DAQe-2213/2214
Data Acquisition Module
ADLINK DAQe-2213/2214 can sample up to 16 AI channels with different gain settings and scan sequences. It makes them ideal for dealing with analog signals with various input ranges and sampling speeds. These devices also offer differential mode for 8 AI channels in order to achieve maximum noise elimination.
-
Product
High Performance Data Acquisition
CPCI-AD8
Data Acquisition Module
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8/16 can also accept external scan and trigger signals from a front panel connector.
-
Product
8-CH Thermocouple Input Module
ND-6018
Data Acquisition Module
- Channels: 6 Differential & 2 Single-ended- Input Type: Thermocouple, mV, V and mA- Thermocouple Type: J, K, T, E, R, S, B, N,C- Voltage Range: ± 15 mV, ± 50 mV, ± 100 mV, ± 500 mV, ± 1 V, ± 2.5 V- Current Range: ± 20 mA- Isolation Voltage: 2500 VRMS
-
Product
RS-422/RS-485 Repeater
ND-6510
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
8/16-CH 16-Bit 250 kS/s Multi-Function USB DAQ Modules (OEM Version Available)
USB-1901/1902/1903
Data Acquisition Module
The ADLINK USB-1900 series provides a range of USB 2.0-based multi-functional DAQ modules. The USB-1901 and USB-1902 16-bit 250 kS/s USB 2.0-based high-performance DAQ modules allow four different voltage input ranges, while the USB-1903 features additional built-in precision current-tovoltage resistors capable of direct measurement of current signal from 0 to 20 mA. The USB-1900 series is USB bus powered and equipped with removable screw-down terminals for easy device connectivity. The attached multi-functional stand can be used for desktop, rail, or wall mounting. Suitable for mixed-signal tests, laboratory research, and factory automation, the USB-1900 series provide a simple measurement solution at an affordable price.
-
Product
Data Acquisition 32 ch. Module
CPCI-AD16/16-6U
Data Acquisition Module
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
Product
4DI/4 Relay Output Modbus RTU Remote I/O
ND-6160
Data Acquisition Module
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
Product
Data Acquisition System
DAQ973A
Data Acquisition System
Get the next-generation data acquisition (DAQ) system with a three-slot mainframe and your choice of nine plug-in modules. Interface with the DAQ using Keysight BenchVue DAQ software or use the intuitive graphical front panel with task-oriented, self-guiding menus.
-
Product
19” Rackmount Data Collection System
DCS-211
Data Acquisition System
- Intel Atom® x5-E3930 processor- Up to 8x DI and 6x DO with two 2A relays- 3x M12 GbE, 1x RJ-45 GbE, 2x isolated RS232/422/485, 2x USB and one lockable HDMI port- Up to 3x PCI Express mini slots with one USIM card slot each- Storage: up to 64GB eMMC 5.0, 1x 2.5” SATA drive bay
-
Product
6U High Performance Data Acquisition subsystem
CPCI-AD320
Data Acquisition Module
The CPCI-AD320 module provides a 6U high performance data acquisition subsystem. There are 32 thirty-two 100/200 KSPS ADC’s for maximum performance. Or an opt low cost 16 channel version. The Local DSP can be usedto simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection and gain on a per channel basis. The CPCI-AD8320-6U can also accept external scan and trigger signals from a front panel connector.
-
Product
Data Acquisition DSP Based 16 Channel
CPCI-AD8-opt8
Data Acquisition Module
The CPCI-AD8/16 module provides a 3U high performance data acquisition subsystem. There are (8) eight or (16) sixteen 100/200 KSPS ADC’s for maximum performance. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digital filtering, etc. Software can be downloaded to the DSP via the CPCI interface.
-
Product
High Voltage System
HV-2
-
International Electro-Magnetics, Inc.
*Tests Power Transformers for Continuity, Ratio and Phase. Applied and Induced Potential and No-load Losses.*14 Conductor Switching Matrix will test 7 individual windings, 13 taps of one common winding or some combination thereof. (10 Amp current limit)*The System Control is Windows/Visual Basic based. Menu screens allow full selection of test parameters and sequence. Low voltage tests can be performed first, allowing defective parts to be rejected without proceeding to time consuming induced Potential dwell routines. Test data labeling and data acquisition software can be easily added to the system.
-
Product
8-CH Analog Input Module
ND-6017
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
64-CH 16-Bit 250kS/s Multi-Function DAQ Card
cPCI-9116
Data Acquisition Module
- PICMG 2.0 Rev 2.1- 16-bit A/D and sampling rate up to 250kS/s- 64-CH single-ended or 32-CH differential input- On-board 1k-sample A/D FIFO
-
Product
8AI Modbus RS-485 Remote I/O
ND-6117
Data Acquisition Module
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
Product
15-CH Isolated Digital Input Module
ND-6054
Data Acquisition Module
- Channels: 15- Isolation Voltage: 5000 VRMS- Switching Level: with 24 V common power. Low (0): 22 V min.; High (1): 0-22 V- Programmable input polarity
-
Product
Digital I/O Module
ND-6050
Data Acquisition Module
- Interface: RS-485- 7 TTL digital inputs- 8 open collector DO- Output up to 30V, 30mA max. load- Programmable input polarity
-
Product
Configurable Data-Logging System
NI CompactDAQ
Data Acquisition System
This NI CompactDAQ configurable data-logging system includes an NI CompactDAQ controller or chassis, C Series I/O modules, and Chameleon software. It is designed for structural test and monitoring applications with the NI CompactDAQ controller, which includes built-in processing and nonvolatile storage for running Chameleon software and logging data locally. Alternatively, you can choose a USB or Ethernet chassis for a lower cost system that requires an external PC. This system accepts a variety of C Series I/O modules, so you can mix and match microphones, accelerometers, and temperature and bridge-based sensors.
-
Product
COM-HPC Server Type Size E Reference Development Platform based on Ampere® Altra® SoC
Ampere Altra Developer Platform
Software Development Kit
Backed by a broad Arm® ecosystem with an Ampere® Altra® SoC at its core, using the Arm® Neoverse™ N1 platform, the Ampere Altra Developer Platform provides premium performance from a cloud-to-edge infrastructure, keeps an extremely low thermal envelope, lower TCO, and significantly lower power consumption than x86 designs. It supports the open source EDKII as bootloader with UEFI, so customers can just download a stock AArch64 (arm64) ISO such as Ubuntu and install it through booting a live ISO directly on the target. The same convenience we have become used to by using x86 / amd64 target systems.
-
Product
Intelligent 16 Bit Data Acquisition
CPCI-AD16
Data Acquisition Module
The CPCI-AD16 module provides a 3U high performance data acquisition subsystem. The Local DSP can be used to simply move data samples to the CPCI bus or can provide processing functions such as limit checking, FFT’s, digitalfiltering, etc. Application software can be downloaded to the DSP via the CPCI interface. Instrumentation amplifiers provide over-voltage protection, gain and filtering on a per channel basis. Internal scan and trigger clocks are derived from either the CPCI bus clock or the local DSP clock. Dual 32 bit timers can programmed to pace the acquisition process. The CPCI-AD16 can also accept external scan and trigger signals from a front panel connector.
-
Product
Modular and Scalable Multifunction Switch/Measure Units
EX1200 Series
Data Acquisition Module
The EX1200 product family is a modular and scalable series of multifunction switch/measure units that can be configured to address a variety of applications in the mechanical data acquisition and electronic test environments.
-
Product
16-CH Digital Input Module
ND-6053
Data Acquisition Module
- Channels: 16 DI- Channels: 16 DI: Logical 0: close to GND; Logical 1: open; Effective distance: 500m- Wet contact: TTL level- Programmable input polarity
-
Product
Windows Driver & SDK for ADLINK USB DAQ Series Data Acquisition Modules
UD-DASK
Data Acquisition Module
ADLINK DASK drivers are the device drivers for custom data acquisition applications for Windows. The DASK driver libraries provide API sets for ADLINK PCI ExpressR, PCI, CompactPCI, PXI and USB data acquisition cards, to access full hardware functionalities, such as buffered/double-buffered data acquisition, pattern generation, digital input/output and etc. For novice users, the built-in CodeCreator utility helps you create your first program in just a few minutes.
-
Product
I-Pi SMARC Development Kit based on MediaTek® Genio 1200 platform
I-Pi SMARC 1200
Software Development Kit
The I-Pi SMARC 1200 is a SMARC-based, AI and graphics-centric solution development kit powered by MediaTek® Genio 1200 (Octa-core Arm Cortex-A78 x4 + A55 x4) processor with a 5-core Arm Mali-G57 GPU for advanced 3D graphics and an integrated APU (AI Processor Unit) system delivering up to 5 TOPS.
-
Product
48-Ch TTL DI/O IDAQ Module
iDAQ-751
Data Acquisition Module
Hot-swappable in iDAQ systemDetachable Euro-type spring terminal connectors48-channel TTL digital I/OsConfigurable digital I/O directionIsolation protection of 60 VDCSupports buffered acquisition/update rates up to 200kHz
-
Product
Digital Management Software
EdgeGO
Digital Management Software
EdgeGO® is a robust software platform for remote device management in edge computing environments. It prioritizes quick deployment and user-friendly operation while ensuring scalability and security.
-
Product
Windows On Arm Development Kit
EPC-R3720
Software Development Kit
EPC-R3720 w/ UIO-4032 and Windows On Arm
-
Product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
Data Acquisition Module
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
Product
COM-HPC Server Type Development Kit based on Ampere® Altra® SoC
Ampere Altra Dev Kit
Software Development Kit
Ampere Altra Dev Kit consists of a COM-HPC Server Base carrier paired with a COM-HPC Server Type Size E module and heatsink with fan. The module features Ampere® Altra® SoC (Arm Neoverse N1-based architecture) harnessing 32/64/96/128 Arm v8.2 64-bit cores for up to 1.7/2.2/2.8/2.6 GHz and providing support for up to 768GB DDR4 memory, offering unprecedented performance and power per watt with exceptional scalability.
