Discrete I/O
-
Product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
-
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
Product
RTM Analog & Discrete Signal Conditioning Board
-
CPCI Rear IO Analog and Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3663i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector. And Board takes 16 Analog outputs and 64 Analog inputs from ACIO and does signal conditioning. In addition it shall generate additional 40 Analog input and 32 Analog output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M8KDiscrete
-
The M8KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M8KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports ten programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each.
-
Product
Complete Solution for Developing & Testing Discrete Voltage-Level Interfaces
M4KDiscrete Module
-
The M4KDiscrete module provides a complete solution for developing and testing discrete voltage-level interfaces. The M4KDiscrete contains control I/O registers that are memory-mapped and may be accessed in real time. The module supports twenty programmable I/O discretes that can record or control the external discretes that are connected to it. In addition, the module can record changes in the input discrete with an associated time tag via a built-in FIFO. Output discretes are open collector, capable of handling up to 32V with a maximum sink current of 100 mA each. Ordering Information:The user can set each discrete:• Either as input or output.• Either to TTL (0 – 5V) or Avionics (0 – 32V) voltage levels on inputs and• Either enable or disable external debounce on inputsThere is a 4092 Word FIFO (a string of 1023 discrete entries) containing the data and time tags.The M4KDiscrete module is supplied with C drivers, including source code and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.
-
Product
Aircraft Data Recording
COTS
-
Our powerful and flexible Ballard Avionics I/O Computers provide the platform for Silo Data recording. These rugged, conduction-cooled, COTS devices combine a powerful computer processor, multi-protocol databus interfaces (MIL-STD-1553, ARINC 429, ARINC 717, ARINC 708), Ethernet, USB, serial, discrete I/O, and other I/O in a small, lightweight package. They deliver outstanding performance on the ground and in the air and are routinely deployed on helicopter, fixed wing, ground mobile, and marine platforms.
-
Product
Data & Protocol Converter
uMACC
-
The uMACC is a wholly contained Communications Converter (data converter - protocol converter or translator). Its small size makes it a complete solution for developing & testing both in the lab and in the field.The uMACC can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to Analog
-
Product
SWaP Optimized Processing and Multifunction I/O & Communications System
NIU3A
-
The NIU3A is a small, rugged, low-power, self-contained processing and multifunction I/O system preconfigured with 24-CH programmable Discrete I/O, 8-CH ARINC 429/575, 4-CH CANBus and 2-CH MIL-STD-1553 functions. The NIU3A can also be configured with up to three smart Configurable Open Systems Architecture™ (COSA®) function modules. The NIU3A boasts Dual or Quad Core ARM Cortex®-A53 processors for customer software applications and I/O and communications management. The NIU3A is configured with two 10/100/1000BASE-T (GbE) Ethernet ports and an RS-232 port for maintenance / diagnostic or configuration interface. Ideally suited for rugged Mil-Aero applications, the NIU3A delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
Product
6U CPCI Multifunction I/O Board
78C1
-
The 78C1 is a universal 6U cPCI Multifunction I/O Board that eliminates the complexity and size constraints of using multiple, independent, single-function cards. This single slot card has six module positions, allowing developers to achieve a custom configuration with any combination of function modules, such as A/D (10-channels), D/A (10-channels), Discrete I/O (16-channels), TTL I/O (16-channels), Differential Multi-Mode Transceivers (11-channels), RTD (6-channels), Synchro/Resolver (4-channels), LVDT/RVDT (4-channels), and Signal Generator (4-channels).
-
Product
Modbus RTU Analog Input
-
Provide direct connection to a wide variety of sensors to any host with an RS232 or RS485 port. The modules perform all signal conditioning, scaling, linearization, and A/D conversion. They each contain some discrete digital I/O lines and can measure signals such as:
-
Product
PC Card
I/O Mezzanine modules
-
MAX Technologies’ IPM mezzanine modules are available for MIL-STD-1553, ARINC 429, ARINC 561, ARINC 568, ARINC 629, ARINC 708, ARINC 717, SERIAL ASYNC RS-232/422/485, CSDB, ASCB, HDLC/SDLC, Pulse/Frequency generator, Analog, Single and Differential Discrete I/O and more.
-
Product
ARINC 429 XMC Interface Module
XMC-429
-
Avionics Interface Technologies
16, 32, or 64 ARINC 429 channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable high/low speed operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - IRIG‐B time code encoder/decoder for data correlation - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - ANSI Application interfaces supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, and VxWorks (others provided upon request)
-
Product
PMC Module
PMC-601
-
Curtiss-Wright Defense Solutions
The PMC-601 PMC module allows customers to incorporate MIL-STD-1553 and discrete digital I/O connectivity into military and aerospace embedded computing systems. We assure an easy integration with other elements of our product lines, as well as after-sales technical support, life-cycle management services, and the commitment to long-term availability.
-
Product
3U cPCI I/O & Comm Board
75C3
-
NAI’s 75C3 is a 3U cPCI multifunction I/O and communication board with three independent function module slots. Two of the slots can be configured with a variety of I/O and communication functions; the third, with either a combination module featuring four multiplexed A/D channels and 28 Discrete I/O programmable channels, or with a reference supply. Using multiple DSPs, the enhanced motherboard enables higher processing power and dedicated pre-processing control for each module.
-
Product
Miniature Airborne Communications Converter
MACC II - Converter
-
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
Product
Enhanced 16 Discrete/Switch I/O Channels (±80 V, 625 mA/Ch.)
DT5
-
The DT5 module (the enhanced version) features 16 independent, isolated, programmable channels that can be used for input voltage measurements (±80 V), or as a bi-directional current switch (up to 500 mA per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection. Additional features of the DT5 (Enhanced Version) are listed below.
-
Product
4 Discrete/Switch I/O Channels (±100 V, 3 A/Ch.)
DT3
-
The DT3 module (the enhanced version) feature 4 independent, high current, isolated, programmable channels that can be used for input voltage measurements (±100 V), or as a bi-directional current switch (up to 3 A per channel). When programmed as a switch with the switch closed, both the current through the switch and the voltage across the switch can be monitored. These modules include diode clamping on each channel. Clamping is useful for inductive loads, such as relays and short circuit protection.
-
Product
STANAG3910/EFEX Modules
-
AIM’s STANAG3910/EFEX test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O. Configurations with dual redundant concurrent HS/LS Bus Controller (BC), Multiple Remote Terminals, and Chronological/Mailbox Bus Monitor operation with full HS/LS protocol error injection/detection, multi-level triggering, advanced capture/filtering and real time bus recording, time stamping and physical bus replay ensure your bus integrity. Support for EFAbus Direct Digital Links (DDL), Fibre Optic DDL (FODDL) and EFAbus Express extensions (Mixed Mode and Dual Mode operation) are available. To support the French ‘Rafale’ aircraft, modules are available with an Electrical Front End. Single Function variants support cost effective solutions. Each module is delivered with a Board Support Package (BSP) containing the onboard driver software, a full Application Programming Interface (API) and detailed getting started and programming guides. Powerful PBA.pro databus test and analysis software is optionally available for all our STANAG3910 modules.
-
Product
FlexMAX Modules
-
The FlexMAX modules must be inserted into a FlexMAX 1U or 3U chassis. MAX Technologies currently offers ARINC 429, Discrete I/O, MIL-STD-1553, ARINC 708, Serial ASYNC RS-232/422/485, HDLC / SDLC, CSDB, CAN Bus including CAN-FD, Digital to Analog (DAC) and Analog to Digital (ADC) modules. More modules will be added to the portfolio.
-
Product
48 Optocoupled Open Drain 42V 6A Digital Outputs
YAV90048
-
6×8 Isolated Ouput Banks Trigger IN and OUT Termic and Overcurrent protection CAN Control (or Ethernet with Ethernet to CAN Gateway.) Drivers dll & VIs available.
-
Product
Industry Pack Carriers and Digital I/O
CPCI-4pack-6U
-
The CPCI-4pack-6U module provides a high performance flexible I/O scheme, that supports industry standard Industry PacksÔ. For application requiring low cost, high density I/O or unique combinations, the CPCI-4pack-6U is the perfect solution. The Local DSP can be used to simply move data to and from the CPCI bus or provide pre processing functions such as local PID controls, FFT’s, digital filtering, etc. Custom application software can be downloaded to the DSPvia the CPCI bus or the local serial port.
-
Product
PXIe-6376, 8 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module
781475-01
-
PXIe, 8 AI (16-Bit, 3.5 MS/s/ch), 2 AO, 24 DIO, PXI Multifunction I/O Module—The PXIe‑6376 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6376 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
PCI-6115, 4 AI (12-Bit, 10 MS/s/ch, Buffer Rate 32MS), 2 AO, 8 DIO, PCI Multifunction I/O Device
778554-01
-
4 AI (12-Bit, 10 MS/s/ch), 2 AO, 8 DIO, PCI Multifunction I/O Device - The PCI‑6115 is a simultaneous-sampling, multifunction DAQ device. It offers analog I/O, digital I/O, two 24‑bit counters, and digital triggering. The PCI‑6115 is ideal for a variety of applications, such as stimulus/response applications that require synchronization among analog input (AI), analog output (AO), and digital I/O. It is also ideal for 42 V automotive applications, radar, sonar, and ultrasound. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements. The PCI‑6115 dimensions require chassis slots that can accommodate full-length PCI modules.
-
Product
10-CH General-Purpose Timers/Counters & 8-CH Digital I/O Card
PCI-8554
-
- Supports a 32-bit 5 V PCI bus- On-board four 82C54 programmable timer/counter chips- 10-CH independent 16-bit down counters- 1-CH 32-bit cascaded timer- Four programmable clock sources for each timer/counter
-
Product
USB-6366, 8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device
782263-01
-
8 AI (16-Bit, 2 MS/s), 2 AO (3.33 MS/s), 24 DIO USB Multifunction I/O Device - The USB-6366 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, and four 32-bit counters/timers for PWM, encoder, frequency, event counting, and more. Onboard NI-STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The USB-6366 is well suited for a broad range of applications, from basic data logging to control and test automation. The included NI-DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Dynamically Controlled, High Voltage Digital I/O PXI Card With Pin Electronics
GX5055
-
The GX5055 represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the GX5050, the GX5055 offers high performance pin electronics and an enhanced timing generator in a compact, 6U PXI form factor.
-
Product
PXIe Semi-Dynamic Digital I/O Module, 48-Channel
42-419-002
-
The 40-419-002 (PXI) and 42-419-002 (PXIe) are a 48-channel digital I/O modules suitable for operating external devices, such as power, RF and high voltage relays, solenoids and lamps. They can also be used for interfacing with external logic such as a programmable instrument with a BCD interface depending upon the module’s driving capabilities.
-
Product
USB-6509, 96-Channel, 5 V, TTL/CMOS, 24 mA, USB Digital I/O Device
779975-01
-
The USB-6509 is an industrial, bus-powered USB device that can directly drive external digital devices such as solid-state relays (SSRs). You can configure each port for input or output, and no external power supply is … required for outputs. Using programmable power-up states, you can configure the initial output states in software to ensure glitch-free, safe operations when connected to industrial actuators. If a computer or application fault occurs, the USB-6509 can use digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. Programmable input filters eliminate glitches/spikes and provide debouncing for digital switches/relays through a software-selectable digital filter.
-
Product
PXI-6122, 4 AI (16-Bit, 500 kS/s/ch), 8 DIO, PXI Multifunction I/O Module
779179-01
-
4 AI (16-Bit, 500 kS/s/ch), 8 DIO, PXI Multifunction I/O Module—The PXI‑6122 is a simultaneous-sampling, multifunction data acquisition device. It offers analog input, digital I/O, two 24‑bit counters, and digital triggering. The PXI‑6122 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Configurable 6U VME Multifunction I/O Boards
-
NAI offers a variety of rugged 6U VME I/O boards – designed to be combined with our pre-integrated smart function modules – to create a highly flexible COTS-based solution ideally suited for I/O intensive sense, response and communications requirements operating over VME Bus.
-
Product
32 Input, 32 Output USB Modular Digital I/O
U2651A
-
The Keysight U2651A USB Digital I/O is a cost-effective device with its offering of 64 opto-isolated digital lines. It comes bundled with the Keysight Measurement Manager (AMM) software for quick set up and data logging. Simplifying this further is the command logger function offered in the Keysight Measurement Manager that allows capturing of configuration commands that can be easily converted to snippets of VEE code. Other supported languages are VB, C++, and C#.
