Transducer Amplifiers
Increase a transducers signal to measurable levels.
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
-
Product
RF Amplifier
SA831
-
Hangzhou Softel Optic Co., Ltd.
*The microwave low noise amplification circuits are used as forward and backward paths of SA831 products. CATV special RF modules encapsulated by SOT-115 are used as forward paths of SA831 products. The microwave low noise amplification circuits are used as backward paths of SA831 products.*It is more convenient to debug, because of plug-in duplex filters, plug-in fixed (or adjustable) equalizers, plug-in fixed (or adjustable) attenuator plug-in output splitters and scientific and rational on-line detection ports.*The equipment can work steadily outdoor under bad environmental condition, because of waterproof aluminum case, high reliability switching power supply and lightning protection system.
-
Product
VME PWM Servo Motor Driver / Amplifier Board
64PW2
Servo Motor Drive
NAI’s 64PW2 is a 6U VME Servo Motor Driver/Amplifier Board featuring a dual, four-quadrant, bi-directional, PWM servo amplifier. Specifically targeted for DC servo motor applications, this board has an amplified power stage that uses a Pulse Width Modulation (PWM) control signal to provide motor control for both brush and brushless motors. Each motor drive accepts a 65 VDC power input and provides a 5 Amp maximum continuous current output (8.5 Amp peak).
-
Product
10 MHz AGC Distribution Amplifier
FS710
-
Stanford Research Systems, Inc.
For installations which require many 10 MHz outputs at a remote location from the source, the FS710 AGC Distribution Amplifier offers seven independent outputs from one input. With an AGC circuit capable of adding up to 30 dB of gain, this amplifier can be used to provide a 10 MHz reference at locations as far as a mile from the source.
-
Product
Optical Limiting Amplifiers
-
Analog Devices high gain optical limiting amplifiers feature low power, low jitter, and excellent sensitivity performance. Our limiting amplifiers include receiver functions such as quantization, loss of signal detection, and SFF-8472-compliant average power measurement. Along with SFP, SFF, and GBIC MSA module designs, our amplifiers also support physical layer protocols that include 1 ×, 2 ×, and 4 × Fibre Channel, 10GBASE-LX4, multiple rate SONET/SDH up to OC-48 with FEC, and Gigabit Ethernet.
-
Product
High Power Amplifiers
-
Solid State Power Amplifier (SSPA) technology continues to offer opportunities to displace Travelling Wave Tube Amplifiers (TWTA) from radar, communication and Electronic Warfare (EW) applications.
-
Product
Precision Amplifier
-
TI Precision Labs is the electronics industry's first comprehensive online classroom for analog engineers. The on-demand curriculum pairs theory and applied lab exercises to deepen the technical expertise of experienced engineers and accelerate the development of those early in their career. This free modular curriculum includes over 30 hands-on trainings and lab videos, covering analog amplifier design considerations with online course work.
-
Product
Saluki SE1022 DSP Lock-In Amplifier
-
SE1022 Digital Lock-in Amplifier provides an excellent performance within its bandwidth from 1 mHz to 102 kHz. With the advantage of the latest digital signal processing technology and high-precision 24-bit ADC, SE1022 can easily detect the phase and the magnitude of weak signals overwhelmed by various large noises. The performance of SE1022 is as good as other lock-in amplifiers brands, even better in some certain parameters, such as measurement accuracy, SNR, dynamic reserve. Otherwise, SE1022 integrates some special functions like multiple harmonic measurement and FFT, which meets the needs of scientific research and industrial application well.* Saluki SE1022 can be comparable to SRS SR830, even better and more stable.
-
Product
RGB 1×3 Video Distribution Amplifier
VDA403
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
-
Product
Load Cell DIN Rail Signal Amplifier
LCD20
-
Our intelligent strain gauge bridge amplifier is a compact, stackable microprocessor based unit specifically designed to control and monitor process applications. Flexible connection to most load cells, pressure or strain gauges over a wide range of sensitivities. The unit provides isolated current 4-20mA and voltage 0-10V analogue outputs and two digital inputs. Two set point relays can be configured to set thresholds such as net, gross, peak and valley. Powered from a wide ranging DC supply, the DIN rail amplifier is supplied with 2 part screw connectors for ease of installation.
-
Product
Amplified Spontaneous Emissions (ASE) Sources
-
The AP505xA series, high power ASE sources provide stable output power up to + 23dBm and broad flat spectrum over C+L band or T band. They enable effective and efficient measurements for component characterization or optical sensing. Finally, these products are proposed in friendly-user stand alone benchtop instrument with touch sensitive screen, GPIB, ethernet, RS-232 or USB controls.
-
Product
Single Channel High Voltage Linear Amplifier
F20A
-
The F20A is a general purpose broadband linear amplifier having a fixed amplification of 20 times and capable of bipolar high voltage output of ±150V. Any functiongenerator or arbitrary waveform generatoror any othe signal source with amplitude up to ±10 V can be used as an input device. The amplifier's output is linear from DC up to megahertz range. It can be used in a wide range of applications, for example to drive piezo actuators, MEMS, OLEDs, liquid crystals, etc.
-
Product
Solid State Power Amplifiers (SSPAs)
-
CHANGSHA KAIYUAN INSTRUMENTS CO., LTD.
* Ruggedized for use in pulsed airborne, naval and ground radar* Found in weather forecasting Doppler radar systems* Utilized world-wide in air traffic control and precision approach radar systems
-
Product
SparkFun Qwiic Thermocouple Amplifier
MCP9600 (Screw Terminals)
-
The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 can read both the ambient temperature and the temperature of whatever you're trying to measure! The MCP9600 can do both with a resolution of 0.0625°C, and an accuracy of ±1.5°C (worst-case). The MCP9600 Thermocouple Amplifier is one of our many Qwiic compatible boards! Simply plug and go. No soldering, no figuring out which is SDA or SCL, and no voltage regulation or translation required!
-
Product
Hybrid Raman/Er-doped Fiber Amplifier
HFA5000
-
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600nm.
-
Product
Ku Band Gain Control Amplifier
-
Expanding Teledyne RF & Microwave's existing line of high frequency amplifiers, microwave gain controllable amplifiers are designed and biased for critical performance applications. One example covers 10-13 GHz, offers 45 dB unattenuated small signal gain with 15 dB attenuation range. Typical gain flatness is ±0.5 dB, +35 dBm third order intercept point, +22 dBm minimum 1-dB gain compression, and 3.5 dB unattenuated noise figure 4.5 dB at full attenuation. This is only one of a series of microwave controllable amplifiers currently in production.
-
-
Product
Audio Amplifiers
-
An electronic device that increases the strength (amplitude) of audio signals that pass through it.
-
Product
Amplifiers
-
Amplifiers from Analog Devices deliver both high performance and high value. These amplifier ICs combine circuit design, manufacturing process innovation, and applications expertise to create products that simplify signal conditioning design.
-
Product
Signal Amplifier
ZET 410
-
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies.
-
Product
Panel-mounted Amplifier(Power System Simulation )
PA30Bi-H
-
PA30Bi-H is the panel-mounted type power amplifier model which can produce 3-phase current, with maximum RMS phase current of 30A and maximum output power of 450VA, and 4-phase voltage, with maximum RMS phase voltage of 250V and maximum output power of 75VA.
-
Product
PXI High Voltage Amplifiers
-
Pickering's PXI High Voltage Amplifiers are ideal for increasing the output voltage from other PXI modules, enabling users to easily generate the signal voltages commonly required in applications such as automotive test. Each amplifier can be independently programmed to a gain of 1, 2, 5, 10 or 20, enabling it to be used with modules with low output voltage capability. Inputs and outputs can be provided either on SMB connectors or on a D Type connector to suit the user’s wiring system.
-
Product
Low Phase Noise Amplifiers
-
Macom Technology Solutions Holdings Inc.
MACOM is committed to an expanding portfolio of low-phase noise (>150dBc/Hz @ 1k Hz offset) amplifiers for critical signal generation applications in test and measurement and defense. These offerings complement our line of NLTL GaAs comb generators.
-
Product
Broad Band Amplifiers
-
Broad band amplifiers (A.K.A. wide band) from Fairview Microwave provide amplification for radio frequencies in broadband. Our broad band amplifiers applications include: military / defense, test instrumentation, EW/ECM, radar, satcom, telecom, microwave radio and various industrial RF, microwave and millimeter wave applications. Fairview broad band amplifiers have a maximum frequency as high as 18 GHz depending on the amp configuration.
-
Product
Compact Pressure Transducers And Switches
-
Compact Baratron® capacitance manometers are ideal for space constrained applications. Compact pressure transducers provide an analog output proportional to pressure, while compact pressure switches provide a relay output based on pressure.
-
-
Product
DVB-T Amplifier Module
-
The COMM-connect DVB-T Amplifier Module is a very versatile module, for use in multiple applications, including driving High Power amplifiers or stand alone Gap-filler. The amplifier covers both VHF & UHF bands, and can be combined with several COMM-connect filter options.
-
Product
Open Loop Hall Effect Current Sensors Transducers With Rectangle Windows
-
ChenYang Technologies GmbH & Co. KG
This Hall Effect current sensor is based on open loop principle and designed with a highgalvanic isolation between primary conductor and secondary circuit. It can be used formeasurement of DC current, DC pulse currents etc. The output of the transducer reflects thereal wave of the current carrying conductor.
