Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
Vector Network Analyzers
ZND
Vector Network Analyzer
The R&S®ZND network analyzer performs unidirectional measurements up to 4.5 GHz in the base model. It can be expanded to perform bidirectional measurements and the frequency range can be extended to 8.5 GHz. The large R&S®ZND touchscreen is easy to operate making it ideal for S-parameter measurements, even when many diagrams are needed. Time domain measurements can also be added for even more functions.
-
Product
PXI-6236, 4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module
779622-01
Multifunction I/O
4 AI (16-Bit, 250 kS/s), 4 AO, 6 DI, 4 DO, Bank-Isolated, PXI Multifunction I/O Module—The PXI‑6236 is a bank-isolated DAQ device designed for current I/O. It offers analog I/O, digital input, digital output, two 32‑bit counters, and digital triggering. The digital input and outputs are compatible with 5 V TTL/CMOS signals. It combines the safety and performance benefits of isolation with high-performance timing, amplification, and calibration technologies to offer accurate measurements and precise control. The PXI‑6236 is ideal for test, measurement, control, and design applications in environments with high voltages and electrical noise. You can use the PXI‑6236 to read from encoders, flow meters, and proximity sensors as well as control valves, pumps, and relays.
-
Product
16-channel, 1GHz, 1Mb/ch USB Logic Analyzer Plus 8-Channel Pattern Generator
LA-Gold-16
-
A maximum sampling rate of 1 GHz is available on all channels. The LA-Gold-16 has a large data buffer of 1 Mega samples per channel for sampling rates of up to 500 MHz on all 16 channels. The large buffer allows long capture times at high sampling rates. The digital logger function is for capturing very slow varying signals, e.g. room temperature.
-
Product
High Voltage 50 Ω Pulse Generator
TLP-4010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Ultra fast 50 Ω high voltage pulse output with typical 100 ps rise time*Built-in HMM (IEC 61000-4-2) pulse up to ±10 kV*High pulse output current up to ±40 A*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns*Optional pulse width extender increases pulse width up to 1.6 µs in 68 programmable steps*Fast measurement time, typically 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurement of complete wafers*High performance and high quality components
-
Product
50 µs Pulse Medium Current Source/Measure Unit (MCSMU)
B1514A
Source Measure Unit
The 50 s Pulse Medium Current SMU is an SMU designed for faster pulsed IV measurement. It enables a pulsed measurement down to 50 s pulse width, a 10 times or more narrow pulsed measurement than provided by a comparable conventional SMU. In addition, the instrument offers a wider range and versatility, up to 30 V / 1A, with voltage/current programmability. It is useful to characterize high to medium power devices on the new materials such as SiC and GaN, and organic devices, and the MCSMU expands your choices of pulsed IV measurement.
-
Product
Wireless Temperature Data Logger w/ Digital Display
RFTemp2000A
-
The RFTemp2000A is a wireless data logger featuring a digital display. The device measures ambient temperatures, making it ideal for monitoring perishable goods, chemicals and more. Starting, stopping and downloading from the device are all performed wirelessly using the RFC1000 wireless transceiver, allowing the user to spend less time maintaining the data logger. Data can be provided in real time back to a central PC, or the device may be downloaded at periodic intervals.
-
Product
Programmable DC Power Supply
M88 series
-
M88 series power supply are high performance single-output programmable DC power supply with communication interface, possessing the character of fast rise speed (The rise time of M8811 power supply can be less than 10ms and that of M8851 can be less than 20ms). The combination of bench-top and system features in these power supply provides versatile solutions for your design and test requirements. The M88 series can not only be programmed through the keyboard on the panel, but also be functioned as voltmeter and milliohm meter, which will bring great convenience to the users. As a regeneration product of ordinary programmable power supply, M88 series power supply are more cost-effective.
-
Product
Technology Insertion
-
Technology insertion allows customers to seamlessly integrate new, higher performance hardware technologies while retaining form, fit and function and application software compatibility.Over that time, application requirements change and grow – demanding greater computing horsepower. In recognition, we have put technology insertion at the heart of our product design, enabling our customers to leverage new levels of capability at lower cost and with minimal disruption.
-
Product
Cyxtera Extensible Data Center
CDX Platform
-
*Provision connectivity and data center services in minutes. *Respond quickly to changes in demand and new requirements. *Procure, configure, and deploy services via API or web console .*Save time and money with remote management tools.
-
Product
Singlemode Power Meters and Laser Sources
-
The KD Optics range of Singlemode power meters and Laser sources are designed for the testing of SDH, CATV, Telecom and other singlemode links. The power meters are highly accurate with a wide dynamic range, while the laser sources feature a very quick stabilisation time, promoting accurate readings.
-
Product
1μΩ-4kΩ AC Milliohmmeter Low Resistance Tester
TH2521
-
Shenzhen Chuangxin Instruments Co., Ltd.
TH2521 AC Milliohmmeter is a high-performance and intelligent tester widely used to test contact resistance, internal resistance and battery voltage. The application of constant current source with 1kHz frequency can greatly eliminate the potential error caused by thermoelectricity on DUT. This meter has the function to automatically detect contact failures on test cable. At the range of 30mΩ, basic R resolution can reach 1μΩ. It is applicable for transformer, inductance coil copper resistance, relay contact resistance, switch, connector contact resistance, wire resistance, PCB line and via reistance dan metal defect detection, etc. In the mean time, signals, such as HIGH, LOW, PASS, can be output through HANDLER interface, thus it is very convenient to be used in automatic production line.
-
Product
Thermometer Hygrometer
Model 302
-
1. Time,date display.2. Time alarm clock every day.3. 12/24 hours system clock.4. ℃/℉ temperature display.5. Relative humidity and comfort display.6. Temperature and relative humidity trend display.7. Max/Min Temperature and relative humidity display.8. Temperature measure range: -20℃~50℃9. Temperature resolution: 0.1℃10. Temperature accuracy: ±1℃11. Humidity measure range: 10%~95%RH12. Humidity resolution: 1%13. Humidity accuracy: ±5%RH14. Measuring period: 20 sec15. Power: 1.5V (AAA or 7# battery)
-
Product
Altitude Test Chamber
-
Environmental adaptability and reliability test for the instruments and meters, electrical products, materials, spare parts, equipments, etc at a low pressure, high temperature, low temperature, under the effect of single factor or multiple factors at the same time. Test for electric performance parameters of the specimen. Mainly used in aviation, aerospace, information, electronics and other industries.
-
Product
Xenon Long Pulse Solar Simulator Three Target Sizes
-
Complies with IEC60904 Class A solar simulation standards.Up to 100ms of effective irradiated time is achieved. Through our proprietary filter technology, spectral concordance conforms to IEC / JIS Class A standards.Three systems provide a wide selection to meet your panel size, floor space, and performance requirements.
-
Product
Antennas
-
LSR is unmatched in offering multiple pre-certified antenna options for each wireless module. Pairing LSR’s embedded modules with a pre-certified RF antenna saves both certification time and costs. The new, exclusive, flexible antenna solutions from LSR, provide unmatched flexibility to help you solve your real-world design challenges. Learn more about the FlexPIFA™, mFlexPIFA™, and FlexNotch™ antennas from LSR and how they can provide design freedoms you didn’t know were possible.
-
Product
USB-8506 , LIN Interface Device
784664-01
LIN Interface
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
PXI/PXIe Solid State Attenuator, Triple, 6GHz, 50Ω, SMA
41-182B-003
Attenuator
The 41-182B-003 (PXI) and 43-182B-003 (PXIe) are programmable RF attenuator modules with 3 channels in one slot capable of inserting a signal loss of 0 to 31.75dB in 0.25dB steps. The attenuators use solid state switches for a long service life and fast operation with minimum settling time and no signal bounce.
-
Product
Stand-Alone Type Chemical Concentration Monitor
CS-100 Series
-
The CS-100 Series offers a complete lineup of high precision chemical solution concentration monitors for various solutions in cleaning and etching processes during semiconductor manufacturing. In addition to the high-speed response and compact design, measurement of each component concentration is conducted in real-time and the timing of chemical solution changes and automatic supply is warned with an alarm. The ability to perform short measurement cycles allows for accurate monitoring of concentration changes.
-
Product
MSF systems
-
Meinberg Funkuhren GmbH & Co. KG
DCF77 / WWVB / MSF systems: DCF77, WWVB and MSF time signal receiver, DCF77 generators, DCF77 simulation
-
Product
8-Channel VME Time-to-Digital Converter
V680
-
The V680 is an 8-channel time-to-digital converter used to record the time of occurrence of eight independent electrical pulse inputs, each measured relative to a single, common reference input. Each input channel can time its event "hit" with 48.82-picosecond resolution and 48-bit dynamic range.
-
Product
Time to Digital Converter-1ns 5ch
FMC TDC
-
Sundance Multiprocessor Technology Ltd.
An FPGA Mezzanine Card (FMC) with a Time to Digital Converter chip to perform one-shot sub-nanosecond time interval measurements.
-
Product
Cinema-Level Imaging - Super Starlight Series
SL Series
-
Cinema-level imaging texture allows intelligent images to cover all time periods and more application scenarios
-
Product
VCS
Harmonic Vibration
-
The Harmonic vibration program is intended for harmonic oscillations resistance testing within the specified frequency range or at a fixed frequency during the set time interval.
-
Product
Anemometers
-
GAOTek offers an extensive selection of high quality, budget friendly and precise anemometers for purchase. Featuring fast response times, multi-function measurements as well as intelligent signal processing for maximum reliability and stability, GAOTek’s category of Anemometers provides users with the best anemometers of any type. Our Anemometers are available for purchase in the United States, Canada and globally.
-
Product
Transistor-Level Defect Simulator
Tessent DefectSim
-
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
Product
PDS Pile Driving Software
-
Teledyne PDS customers can now use the high-performance software for Pile Driving applications, including guidance and monitoring, which will reduce production time significantly.A pile data file with pre-engineering information (such as position and orientation information) is used as guidance during real time operations. The operator selects the pile to be placed and Teledyne PDS then expertly interprets the environment and will display all relevant information to the user.
-
Product
Custom Test Fixtures
-
Cortek Test Solution’s design capabilities range from very basic to extremely sophisticated solutions. Developing custom test fixtures demands more engineering time as well as an in-depth knowledge of mechanical design, pcb test methods paired with precision machining. Our experienced engineers will evaluate your requirement and design innovative mechanical test fixtures to meet your application needs in both the R & D and production environments.
-
Product
PIN Photodiode
-
PIN photodiode is a kind of photo detector, it can convert optical signals into electrical signals.This technology was invented in the latest of 1950's. There are three regions in this type of diode. There is a p-region an intrinsic region and an n-region. The p-region and n-region are comparatively heavily doped than the p-region and n-region of usual p-n diodes. The width of the intrinsic region should be larger than the space charge width of a normal p-n junction. The PIN photo diode operates with an applied reverse bias voltage and when the reverse bias is applied, the space charge region must cover the intrinsic region completely. Electron hole pairs are generated in the space charge region by photon absorption. The switching speed of frequency response of photo diode is inversely proportional to the life time. The switching speed can be enhanced by a small minority carrier lifetime. For the photo detector applications where the speed of response is important, the depletion region width should be made as large as possible for small minority carrier lifetime as a result the switch speed also increases.
-
Product
Cots Boards
-
Built in strict adherence to open architecture standards, Data Patterns designs COTS module products which are used in today's rugged applications and automatic test equipment platforms. Open standard form factors include cPCI, FMC & XMC, IP, MM, PCI, PCMCIA, PMC, VME, VPX and VXI.A portfolio of 'Off the Shelf ' products for testing and on-board applications have been developed by Data Patterns. COTS boards developed have been sold to many customers, in India as well as Europe and North America. They are used for system level products such as Automatic Test Equipment, Rugged Military Electronics, etc.Data Patterns focus on building COTS product is to provide the technological capability to develop system level products with very fast run around times. Use of Data Patterns' COTS module in system level products ensures Data Patterns ability to maintain the products for a significantly longer life cycle. The proximity to the system level engineering team with the COTS development team ensures that end applications are delivered faster, enabling a shorter time to market for the customers
-
Product
Software Tool Especially Designed for Production Process Supervision
LEON OP
-
The Leon OP is a software tool especially designed for production process supervision. Therefore, the application provides the following key features:- Execution of KT ICT sequences or NI TestStand sequences- Parallel, semi-parallel or sequential execution of test sequences, individually definable per Test Sequence- Customizable User Interface, simple or detailed test views, grid or board layout arrangement possibilities- Tracing into sequence execution- User management with different user levels and restrictions per user group- Displaying execution results and statistics by panel or nest- Supporting interaction with an automation (e.g.: handler system)- Supporting interaction with a process control / MES system- Integrated Callback structure to adopt to different workflows- Maintenance view for fast displaying of fails inside a board- Result History View to quickly access the last test results- Store execution results in result files with user defined format- Autostart-option for running application in automation mode without any operator interaction at all- Several abortion criteria to abort execution by fail count (consecutive or time based)- A Maintenance View for viewing testprobe locations on the DUT is available via Aster Quadview
