Conductance
See Also: Battery Conductance Testers
-
product
Avionics Radio and Pulse Tester
T-RX
Streamline your avionics radio testing process with the CCX Technologies T-RX Avionics Radio and Pulse Tester. The T-RX is an all-in-one avionics tester that conducts 100+ tests on over 16 systems with only 1 device!
-
product
Optical Spectrum Analyzer Module
OSAPXIe
OSAPXIe enables new measurement capabilities in PXI for truly effective mixed-signal testing. Conduct all your DUT characterization from one platform and spend less time switching cables and patchcords between instruments.
-
product
PXI 3A Power MUX BRIC, 5-Channel, 48-Pole
40-571-005
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Flocculation Jar Tester
LD-LFC-A12
Flocculation Jar TesterLD-LFC-A12is designed to stimulate the process of adding reagents, precipitation, coagulation reaction which occurs in water testing procedures. Features desktop, 6 round shaped or square shaped beakers, each with 1.0 L and 1.5 L capacity respectively. With 10 to 1000 rpm speed, this flocculation jar tester conducts synchronous as well as independent running operations. It is used to carry out the jar test during water treatment procedure.
-
product
Software
Conductance Measurement and Analysis
Materials Development Corporation
MDC uses conductance to give a complete picture of MOS devices as well as to correct for series resistance effects. MDC C-V plotters use conductance and capacitance measurements to plot true device capacitance and depletion region conductance.
-
product
Handheld Water Quality Meters
LAQUA PC220
- Automatic pH calibration - up to 5 points (NIST, USA pH buffers) / up to 6 points (DIN pH buffers)- 0.01 pH resolution- Offset and average slope display- ORP calibration option- Automatic / manual temperature compensation and temperature calibration function- Automatic (up to 4 points) and manual (up to 5 points) conductivity calibration- Adjustable reference temperature and temperature coefficient- Adjustable cell constant and selectable measurement unit- Conductivity and total dissolved solids (TDS) conversion- Four (4) TDS calibration curves for wide range of applications: EN27888, Linear, 442, NaCl- Two (2) salinity calibration curves: NaCl, Seawater- With real-time clock and date/time stamp for GLP compliance- Auto log data; built-in memory can store up to 1000 data- Auto shut-off (programmable: up to 30 minutes)- Auto stable, auto hold, and real time measurement modes- Calibration alarm (programmable: up to 90 days)- Built-in electrode holder allows 2 electrodes to be attached - Monochrome LCD with white LED backlight: 50 x 50 mm- Phono jack output for connecting meter to computer via PC (USB) cable for data collection and to printer via printer (RS232) cable for printout - Casing is IP67 waterproof/dustproof, shock & scratch resistant, non-slip- Powered by 2 x AA batteries- Packaged with electrodes and calibration solutions in carrying case- 3 years meter warranty
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
product
Rugged Conduction Cooled 3U CompactPCI Processor Blade with Quad-Core Intel® Atom™ Processor
CT-3620
The ADLINK CT-3620 Series is a Rugged Conduction-Cooled 3U CompactPCI processor blade in single-slot (4HP) width form factor featuring a quad-core Intel® Atom™ SoC and soldered DDR3L-1333 ECC memory up to 4GB. Graphics is integrated graphics on the CPU and storage is provided by an onboard 32GB SSD. Rear IO signals include 2x GbE, 1x USB 2.0, VGA, 2x COM, and 1x SATA 3Gb/s, providing for expansion with an optional Rear Transition Module (RTM).
-
product
Chip Manufacturing
KLA’s advanced process control and process enabling solutions support integrated circuit manufacturing. Using KLA’s comprehensive portfolio of defect inspection, review, metrology, patterning simulation, in situ process monitoring and data analytics systems, IC manufacturers can manage yield and reliability throughout the chip fabrication process - from research and development to final volume production. SPTS provides deposition process solutions for insulating materials and conducting metals that cover a range of chip manufacturing process steps. IC manufacturers use KLA's array of products and solutions to help accelerate their development and production ramp cycles, to achieve higher semiconductor die yield and improved IC quality, and to improve overall profitability in the IC manufacturing process.
-
product
Guarded Heat Flow Meter
The Guarded Heat Flow Meter (GHFM-02) follows ASTM E1530-19 for testing thermal resistance and thermal conductivity of solids, such as metals, polymers and composites. The easy to operate GHFM-02 follows the trusted steady-state approach, with the addition of a guard to limit the effects of lateral heat loss. This design, allows testing of a wide range of materials with low to medium thermal conductivity.
-
product
Formaldehyde Emission Climatic Test Chamber
TESTEX Testing Equipment Systems Ltd.
The internal test room is made by high quality SUS304 stainless steel; heat insulating material: high density fiberglass wool; insulation material thickness: 80mm.The heat inside the internal room may not be conducted.
-
product
High Elongation Extensometers
Model 3800
Jinan Testing Equipment IE Corporation
The main body of this unique extensometer remains stationary during testing, held in position by the adjustable magnetic base included. Only the very light, small traveling heads move as the sample elongates during a test. These attach to the sample with small spring clips. Each head pulls a cord out from the extensometer as the head moves. These models use high precision, low friction potentiometers, and, as a result, have a wide range of factory selectable outputs. The extensometer is driven by an excitation voltage and has output proportional to the input. They can be provided with high level outputs (approximately 2-8 VDC) or ones that mimic strain gaged devices (2-4 mV/V). When set to mimic strain gaged extensometers, the Model 3800 can be used with virtually any signal conditioning electronics designed for strain gaged sensors. The potentiometers employ a hybrid wire wound around conductive plastic, which provides excellent long term stability. The output from the extensometer is readily interfaced with most existing test controllers, and may be directly input to data acquisition systems and chart recorders. Please let us know at the time of order what type of output and connector you require.
-
product
Energized Tester
ALL-SAFE PRO
Conduct safe, easy and accurate ESA testing in only 60 seconds with the ALL-SAFE PRO® motor connection box. The ALL-SAFE PRO® is a permanently installed connection accessory for the ATPOL III™ energized testing instrument. With this electric motor connection box, the ATPOL III™ can perform tests easily with a quick disconnect.
-
product
PXI 3A Power MUX BRIC, 32-Channel, 6-Pole
40-571-404
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
product
Radiation Monitoring Systems
Monitoring the radiation situation on the territory of radiation-hazardous and radiation-sensitive objects and premises, conducting radiation monitoring of the environment.
-
product
Conductivity and Temperature Water Pocket Meter
LAQUAtwin EC-22
The only pocket meter that directly measures conductivity in 0.12ml sample. No need for a beaker to calibrate your meter or measure a sample. Just place few drops of the standard or sample onto the sensor. This procedure saves you time and prevents wasting your precious sample.
-
product
Test Adapter
cPCI/VME/VME64x
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
product
CDN - Coupling / Decoupling Networks
The Coupling- / Decoupling Networks are used to inject common mode disturbances to Equipment under Test (EuT). Further the CDNs provide sufficient decoupling between Auxiliary Equipment (AE) and disturbance signal. The requirements for CDN and their application are described in the standard IEC 61000-4-6 (Immunity to conducted disturbances, induced by radio-frequency fields). CDNs have a common mode impedance of 150 Ohm and are available for a multitude of cable types and connectors.
-
product
Oxygen / Hydrogen Analyzer
ELEMENTRAC OH‑p 2
The new ELEMENTRAC OH-p 2 is a powerful and robust elemental analyzer for measurement of oxygen and hydrogen concentrations in inorganic samples like steel, iron, copper or ceramics. The highly sensitive NDIR and thermal conductivity detectors reliably detect element concentrations from low ppm content to high percentages.
-
product
Conductivity-Thermometer
HD2106.1
conductivity, liquid resistivity, total dissolved solids, salinity and temperature.
-
product
Battery Capacity Tester
BLU-C Series
BLU-C is the latest solution from DV Power for conducting a comprehensive battery capacity test. This universal instrument is applicable to any battery string, such as lead-acid, Li-Ion, Ni-Cd, and others, with voltages up to 800 V DC.BLU-C tester simplifies battery testing in multiple ways. The instrument provides monitoring of discharge parameters (graphically and numerically) in real-time on a 7-inch touch screen display. The instrument also enables measurement and monitoring of cell parameters (voltage/intercell voltage/temperature), which makes it a complete stand-alone discharge test system.The capacity tester is compatible with DV-B Win software. Because of that, the user can view detailed numerical and graphical presentations of key parameters, and create reports in various formats.The capacity test is performed in a user-friendly way according to battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22 and other.The battery tester enables setting the discharge current up to 300 A, with 0,1 A resolution. If higher currents are required, BLU-C units can be connected in parallel, or BXL additional load units can be used.The user can select one of three discharge modes: Constant current, Constant power, Constant resistance. Additionally, different battery duty cycles can be simulated using user-selectable discharge profiles.Testing can be carried out without disconnecting the battery from the equipment it supplies.
-
product
Relaying Current Transformer Analyser
*Measures Ratio, Excitation Characteristics, Polarity, Winding Resistance, Remanance, and Insulation Resistance of secondary winding. * Determines Composite Error. * Used to test un-mounted CTs or CTs that are mounted but isolated inside the power system equipment. * Conducts a whole series of tests automatically, thus speeding up the time to commission CTs and relaying systems. * Battery powered test set - light weight & fully portable. * Provides a graphical presentation of the CT excitation characteristics. * Determines the IEC 10/50 knee point and the point of maximum permeability, ANSI 45 degree Slope Point. * Detects shorted turns or insulation problems within the test CT, thus avoiding commissioning of faulty equipment.
-
product
Impact Testing
When you need to evaluate how your product & materials react to shock loading, Trialon is here to help. By utilizing our laser-aiming test stand to create consistent positioning and ball impact, you can trust that Trialon has the equipment and personnel to conduct your test accurately and timely.
-
product
Device Test Kits
Instrument test kits are based on either the multi-parameter DR 900 handheld colorimeter or the Hach DR 1900 handheld spectrometer. Select kits also include the Hach digital titrator, POCKET PRO pH tester and/or HQ40D meter (dissolved oxygen, conductivity, ORP, etc.). Instrument sets are useful for a wide range of applications including potable water, waste water and industrial applications such as boilers and chillers.
-
product
EMC Accessories
Complete your EMC test setup with the essential accessories to compliment the test equipment. Whether it is a LISN (or V-Network) to counteract interference from external power sources on conducted emissions from the device under test, probes to locate the near field sources of radiated emissions, receive and transmit antennas, or tripods for holding antennas in place, the Rohde & Schwarz catalog of EMC accessories provides the additional items you need for EMI and EMS measurements, guaranteed 100% suitable for use with Rohde & Schwarz EMC test equipment.
-
product
Micro and Milliohmmeter
AD-7010
AD-7010 instrument is designed to measure, with high accuracy, the resistance of conductive elements power equipment: motor windings, transformer windings, conductor rails, inspecting the electrical conductivity of bolted joints, crimped, welded, the contacts of switches and relays.
-
product
ALD Periodic Table
The ALD Periodic Table is a visual guide to the elemental building blocks of atomic layer deposition. Organized by both chemistry and purpose, it helps engineers quickly find materials that meet their priorities, whether that’s conductivity, durability, clarity or thermal stability.
-
product
GSR Logger Sensor
NUL-217
The Galvanic Skin Response (GSR) logger sensor measures the conductivity of our skin, especially of our fingers. The conductivity of our skin changes according to unconscious emotion effects such as sudden noise, smell, touch, pain or view.
-
product
Total Organic Carbon Monitor
HT-110
The continuous online TOC-Analyzer HT-110 is suitable for the measurement ot total organic carbons in Purified Water (PW), Water For Injection (WFI) and Highly Purified Water (HPW). The unit is operating according to USP 643. It is applicable for pharmaceutical and/or semiconductor manufacturing. The measuring principle is based on UV-Oxidation and measurement of the difference in conductivity. TOC concentration measurement (TOC concentration 500 ppbC or lower) is necessary to perform quality control according to GMP (Good Manufacturing Practice).
-
product
Conductivity Cell for Ultra Pure Water Measurement
9371-10D
Stainless made Conductivity cell is now available!This conductivity cell is tough to shock and the best choise to measure Organic Solvent as well as Ultra pure water sample by employing the stainless material for its body.
