Conductance
See Also: Battery Conductance Testers
-
Product
Electrical Safety Test Equipment
-
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
Product
Guardian Hipot Analyzer
19055
-
Chroma Systems Solutions, Inc.
Hipot or dielectric withstand testing instruments manufactured by Chroma are used for conducting electrical safety tests on electrical components and products to make certain they are in compliance with IEC, UL, TUV, CSA, EN and other electrical safety requirements. In addition, these instruments are designed for general product or component testing as well as complex medical safety testing (60601-1) ensuring human safety and product reliability.
-
Product
Seismic Acquistion QC Serivices
-
Overall data quality / cost monitoring / safety / daily reporting to client. Verif-i provides technical and operational programme assurances for seismic surveys conducted for the company. The lead acquisition QC on-board/on-crew the seismic vessel/block accepts or rejects data on behalf of the company. Our representative will assist the contractor in fulfilling the technical and operational requirements of the seismic programme and report on crew activities.
-
Product
PRO Waterproof 3-in-1 EC / TDS/Temp Tester
EC60
-
The Milwaukee EC60 PRO Conductivity Tester is designed for hydroponic and other growers to help you make sure that your plants have the ideal amount of nutrient avaiable. Keep EC in your target range to help your achieve better results.
-
Product
ExactFlat Software
-
ExactFlat enables manufacturers to design, flatten, conduct pattern engineering, nest, cost and create manufacturing and business documentation all on one platform.
-
Product
Portable Units
-
The basic version for mobile conductivity measurement. It is a robust and intuitive portable device for routine daily measurements in laboratories and processes. Over 1,000 operating hours with a single set of batteries (4x AA).
-
Product
Lab Coating Machine
-
Dongguan Kejian Instrument Co., Ltd.
This machine is designed for checking the performance of water based adhesive material or similar material on lab or quality department. Trial coating tests are conducted to demonstrate the ability meet any special requirements of our customers.
-
Product
Personal Grounding Tester
PGT120
-
Electronic test apparatus for checking personnel grounding systems such as electrostatic wrist straps and conductive footwear. The unit is equipped with two separate measuring circuits and is therefore capable of checking wrist straps and footwear separately or in parallel. The test result is signaled visually, acoustically (only if error is detected) and via contacts.
-
Product
Conductivity Meter
Cond 6+
-
Multi-Point Push-button Calibration (up to 5 points) with ±1% full scale accuracy :: Option of quick, easy automatic calibration or customised, near-to-sample manual calibration.
-
Product
Safe Discharge Rods
-
These instruments will allow you to conduct the safe damp discharge of the residual charge on the cable / equipment by limiting the discharge current.
-
Product
MARK V “Ranger”
Mk V
-
Radio and audio frequencyInductive or conductive operationOn handle to find unknown structuresInterrupter feature on transmitterVery accurate depth location (triangulation)RF Pipe & Cable locator (Short Locator)Holiday detection of buried pipe (Pearson Method)Volume controlBattery operatedRechargeable NiCad batteries available (optional)
-
Product
Three-Phase Converters
SIRIO 3PH 7 ALFA 3PHSAP
-
The three-phase converter is an electronic equipment able to vary the RMS value of a sinusoidal voltage by controlling no. 6 controlled, antiparallel-connected conducting diode pairs.Since the wave form is symmetrically split both into positive and negative halfwave, the output voltage average value is not affected and equal to zero. This means that three-phase loads can be fed without gene rating inside the mesh a circulating current with average value other than zero.Moreover, the three-phase converting is obtained with only one control circuit thus ensuring balance between the three linked voltages applied to the load.
-
Product
Audio Frequency Output Power Meter
-
PGP Electronics Private Limited
PGP Electronics AF Output Power meter, model 3301provides reliable measurement of Audio Frequency Output Power. The audio power output meter, measurable from 0.01mW to 30W in 12 decades with 10 different termination impedances with both balanced and un balanced inputs. The instrument is very useful to conduct students projects, design and test simple sub systems in laboratories. New improved design features provides reliable working even in adverse environments.
-
Product
PXI High Density MUX BRIC, 5-Chan, 160-Pole
40-570-015
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Tabletop Light Fastness Tester
TF419
-
TESTEX Testing Equipment Systems Ltd.
Tabletop Light Fastness Tester is a powerful xenon instrument with affordable price for conducting accelerated tests of light fastness and photo stability test.
-
Product
5uH Line Impedance Stabilisation Network LISN - CISPR 25
TBOH01
-
The TBOH01 5H LISN is a device required to setup conducted noise measurements of DC-powered devices. It is designed to be used for EMC pre-testing in the frequency range of 150kHz to 110 MHz.
-
Product
Open Frame 3U 34HP Chassis
-
An open-frame solution for the open-minded engineer. With moveable rear profiles (up to 2.5mm,) 3U and 6U backplane compatibility options, air or conduction cooling options and the ease of fast and simple backplane interchangeability for fluid transition between VITA and PICMG bus architectures, the Hartmann Open Frame Chassis solution is the tool for customers who need versatility, accessibility and longevity.
-
Product
Comb Generator
CG 50/500
-
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN.reference signal source Noise Generators Signal Generators
-
Product
PXI High Density MUX BRIC, 40-Chan, 20-Pole
40-570-315
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PMC & ccPMC Card
EXC-1553PMC/Px(S)
-
MIL-STD-1553, conduction cooled, interface board. Supports up to 4 multi function channels.The EXC-1553PMC/Px(S) and EXC-1553ccPMC/Px(S) are multi-channel (up to four) MIL-STD-1553 interface boards for PCI Mezzanine Card compatible computers.
-
Product
Dynamic Electric Motor Analyzers
-
Baker's dynamic motor test and monitoring instruments are built to conduct condition monitoring tests of motors and generators from a Motor Control Centre (MCC), or through a Baker EP1000 connection unit. The Baker EXP4000 dynamic motor analyser is a low-voltage, AC- and battery-operated instrument that test motors and generators while they are in operation. The EXP4000 provides health and performance data on the motor, the motor's load, and incoming power to assess motor performance and suitability in context of the entire machine system it supports.
-
Product
32-Channel RS485/422 Differential
4792
-
The Conduction Cooled 32-channel Reconfigurable RS422/RS485 Digital I/O PMC provides a vehicle for implementing complex user-specific digital designs requiring a differential interface. Thirty-two (32) generalpurpose RS422/RS485 driven digital I/O differential pairs are wired to the rear PN4 connector. For each of the 32 channels, the bidirectionality is controlled by an output from the FPGA.
-
Product
1GHz EMC Emissions Analyser
SA1002
-
The SA1002 provides a high performance capability to measure the EMC compliance of your products. It covers the conducted emission and radiated emission bands to 1GHz, as required by most EMC standards. The included software is Windows compatible and simple to use. This powerful system automatically sets the analyser parameters to suit the test to be performed. Standard limits are available from simple pull-down menu. Results can be directly compared against these limits for easy checks on compliance status.
-
Product
350 W VITA 62 PSU-Conduction Cooled
69-MS215686-RC
-
Designed to meet the requirements of VITA 62 for use in harsh environments. For use in AC systems, they are 3 U high by 5 HP (1-inch) wide modules with guide blocks, for use in conduction cooled VPX systems.
-
Product
PXIe-4353, 32-Channel, 24-Bit PXI Temperature Input Module
781348-01
Analog Input Module
32-Channel, 24-Bit PXI Temperature Input Module—The PXIe‑4353 is a thermocouple input module that provides integrated data acquisition and signal conditioning for temperature measurements. The PXIe‑4353 includes increased accuracy and synchronization features for scalable measurement systems from low‑ to high‑channel counts. The high accuracy is attributed to the NI TB‑4353 isothermal terminal block that optimizes thermal conductivity between the thermocouple terminals and the cold-junction compensation (CJC) channels. The PXIe‑4353 has two auto zero channels for offset compensation as well as open thermocouple detection to identify disconnected thermocouples.
-
Product
Industrial Production Tool
IBP
-
The IBP is an industrial production tool for the structuring of conductive back sheets.
-
Product
PXI High Density MUX BRIC, 16-Chan, 40-Pole
40-570-214
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
Portable Conductivity/TDS Meter with Conductivity electrode
CyberScan CON 11
-
User Customizable Functions for options: Normalization Temperature, Temperature Coefficient, TDS (Total Dissolved Solids) factor, Cell constant and many more
-
Product
Storage Modules
-
Elma offers the most complete line of storage modules in the embedded computing industry. Board sizes include 3 U, 6 U, mezzanine and small form factors in VPX, VME, CompactPCI, PMC and XMC standards. Environmental capabilities address commercial and rugged applications with SSDs (solid state drives) and rotating drives (HDD) and surface mount NAND flash. Choose from features including RAID, front panel removability, high capacity conduction cooled mezzanine storage, secure erasure or write protection.
-
Product
Wafer Sorter and Inspection
SolarWIS Platform
-
Eliminating the opportunity for problematic wafers to enter cell manufacturing lines greatly improves output and yield. ASM AE’s wafer sorter features 3D area inspection capability to inspect wafer thickness, total thickness variation (TTV), saw marks, as well as wafer bow and warpage. SolarWIS also includes modules that can inspect for stain, geometry, micro-cracks, edge chips, resistivity, P or N conductivity and lifetime.
