I2C
IC serial bus protocol speed grades; standard mode: 0.1 / 0.4, fast mode: 1.0 / 3.4 / 5.0 Mbit/s are maximum ratings. Also known as: Inter-Integrated Circuit
See Also: Serial, Serial Communications, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
product
Gyroscope Module 3-Axis L3G4200D
27911
The Gyroscope Module 3-Axis L3G4200D provides raw angular rate and temperature data measurements that are accessed from the selectable digital I2C or SPI interface. The small package design and SIP interface accompanied by the mounting hole make the sensor easy to integrate into your projects. Designed to be used with a variety of microcontrollers, the module has a large operating voltage window.
-
product
PICkit Serial Analyzer
DV164122
The PICkit Serial Analyzer is a low-cost USB-based tool used to direct communication between a PC and an external serial device. I2C™ - Master, I2C™ - Slave, SPI - Master, USART – Asynchronous, USART – Synchronous, LIN (external hardware required to meet electrical specifications), MICROWIRE.
-
product
Hall Sensor Board with I2C Interface
046-322
Version: +5V/15A +12V/5A -5V/15A -12V/5A The Hall-Sensor Board is the right accessory for your system in combination with the Elma SysMon. It's possible to measure up to 4 currents and to monitor them with the Elma SysMon 3 Gen.
-
product
SparkFun Distance Sensor
1.3 Meter, VL53L4CD (Qwiic)
This SparkFun Distance Sensor Breakout utilizes the VL53L4CD next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at short ranges for its size. The VL53L4CD from STMicroelectronics uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an infrared laser to time the reflection to the target. That means that you will be able to measure the distance to an object from 1mm to 1300mm away with millimeter resolution! To make it even easier to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system so no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1”-spaced pins in case you prefer to use a breadboard.
-
product
µModule Isolated Transceivers
Analog Devices µModule (micromodule) isolated transceivers provide robust galvanic isolation for digital serial communication interfaces, including SPI, I2C, RS-485/RS-422, RS-232, and USB. Isolation barriers are implemented using Ethernet transformers, coupling capacitors, or embedded inductors. All devices are simple to configure, have very low EMI susceptibility and emissions, and feature high noise immunity to preserve signal integrity.
-
product
Pico-ITX SBC With Intel® Atom® X5-E3940 Processor, DisplayPort, LVDS, 2 GbE LAN And Audio
PICO319
The PICO319 is powered by the onboard Intel® Atom® x5-E3940 quad-core processor. The noise-free pico-ITX motherboard offers combinations of ruggedness, high computing capabilities and enhanced graphics capability in an extremely compact size of only 100 x 72 mm. Moreover, the board features 12V DC power supply input with AT Auto Power On function. A dual-display capability is available through DisplayPort and 18/24-bit single/dual channel LVDS ports. For extensive storage needs, this compact embedded motherboard has one M.2 Key B slot (22 x 42 mm or 30 x 42 mm) for SATA or PCIe x2 SSD card and one half-size PCI Express Mini Card slot in support of mSATA. The Intel® Atom®-based pico-ITX board comes with rich I/O connectors, including two USB 2.0 ports, two USB 3.0 (USB 3.1 Gen1) ports, one RS-232/422/485 port, one RS-232 port, one HD Codec audio, and 4-channel digital I/O. It also supports SMBus that is compatible with I2C for smart battery support. The PICO319 offers watchdog timer and hardware monitoring function for reliable operation.
-
product
Extension Module
GE-AI-4
Infinite Industrial Informatics Lt
GE-AI-4 is a DIN rail mount, analog input expansion module with I2C serial communication interface. It can be used for the analog input expansion of Infinite's products as the SCOM-100 GSM controller and the iLOGPlus RTU/Data Logger.
-
product
DataComm
SCHILLER AUTOMATION GmbH & Co. KG
With ever-growing performance, accuracy, and precision required by 112G/800G PAM4 solutions, Wilder has designed a robust HCB and MCB fixtures to support OSFP-XD, QSFP-DD, OSFP and SFP-DD compliance testing. In addition, CMIS_GUI Software provides: Displays of many of the settings and Controls in the Module including Lane States, Module Power States and Optical Power. Alarms and Warnings for Module Temp and Vcc and Optical Power Controls for Module Power, Margins, and read access to Descriptors and Data Path Configuration. Direct Read/Write access to the I2C and CMIS Memory Map as well Scripts that directly access the CMIS Memory Map Registers.
-
product
Small outline PCB with 72 Pin Socket
1091-001
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
SIMRC- 72 Pin Simm Socket
1090-001
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
product
High Speed Digital Analog
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
product
Multi Protocol Analyzer
LE-3500R
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
product
SparkFun MicroMod GNSS Carrier Board (ZED-F9P)
With GNSS you are able to know where you are, where you're going, and how to get there anywhere on Earth within 30 seconds. This means the higher the accuracy the better! GNSS Real Time Kinematics (RTK) has mastered dialing in the accuracy of their GNSS modules to just millimeters, and that's why we had to put it on this board! With the flexibility of the MicroMod's M.2 connector, you can easily test and swap out different MicroMod processor boards for your application. Simply match up the key on your board's beveled edge connector to the key on the M.2 connector and secure the boards with a screw. This means solderless access to the ZED-F9P modules features via UART1, UART2, SPI, and I2C ports!
-
product
I2C Soil Moisture Sensor
Capacitive soil moisture sensor interfaced via I2C. Additionaly provides ambient light and temperature readings. Open Source Hardware. Soil moisture sensing, Light sensing, Temperature sensing.
-
product
ST VL53L0X Time-of-Flight Range/Distance Sensor
SEN-36003
Highly integrated breakout board for the ST Micro VL53L0X Time of Flight (ToF) range finder sensor, which builds on the absolute ranging technology introduced with the VL6180X. The VL53L0X drops the ambient light sensing capability of it's predecessor for a 10X improvement in absolute ranging capability, bringing the maximum possible range to 2 meters! As a result, this sensor has even more uses in the robotics, cell phone and gesture recognition space. The SEN-36003 includes the VL53L0X IC mounted between two 4-40 sized mounting holes with on board 2.8V LDO and high-speed signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. All pins are translated to allow interfacing with any microcontroller in the 3V to 5V operating range.
-
product
Computing Power VRM/IMVP
Renesas' computing power products are featured with high accuracy up to ± 0.5%, parallel/serial VID supporting, phase dropping, CCM/DEM mode transition for energy saving, and I2C function. Our multiphase modulation technology comes from our experience in analog multiphase controllers used in computing.
-
product
Grid-EYE High Performance Type
Panasonic Industrial Devices Sales Company of America
Panasonic's Grid-EYE® Series High-Performance Type is an 8x8 (64) pixel Infrared Array Sensor. This Sensor offers digital output (I2C) for thermal presence, direction, and temperature values. The built-in lens includes a 60-degree viewing angle. The Grid-EYE Sensor features compact SMD design using MEMS thermopile technology. This Sensor offers several advancements over the original Grid-EYE, including higher accuracy, enhanced resolution, and longer detection distance for true next-generation performance.
-
product
Sensirion SHT31-DIS-B Humidity and Temperature Sensor Breakout Board
SEN-37002-H
Breakout board for the Sensirion SHT31-DIS-B. This sensor is an extremely accurate digital (I2C interface) temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT1x series, and improves upon the success of the SHT2x that came before it. In addition, the SHT31-DIS-B has a wide input voltage range of 2.4V-5.5V and includes temperature isolation and airflow cutouts as recommended for the optimal operation. Finally, in the case of environmental changes that could cause light condensation, the SHT31-DIS-B has a built-in heater to burn off any condensate.
-
product
Module Spectrum
nRF52833 Series
Nordic nRF52833 solutioin features an Arm Cortex-M4 processor with 512 KB Flash and 128 KB RAM. Supports SPI, UART, I2C,I2S, PMD, PWM, ADC, NFC and USB interfaces
-
product
ARM LPC2294 Based Board
MS 2500
- JTAG interface- Boot Flash interface- External Flash interface for data storage- External Bus interface- SPI Interface- I2C interface- Serial port interface- CAN Interface- LPC2694 based processor board- MIL1553B Bus Interface (Dual Redundancy)
-
product
SparkFun Photodetector Breakout
MAX30101 (Qwiic)
The SparkFun Photodetector Breakout is an updated version of the SparkFun Particle Sensor Breakout includes the MAX30101, a highly sensitive optical sensor and successor to the MAX30105 and MAX30102. The MAX30101 Breakout utilizes a photon detector to measure the amount of returning light that is reflected back from the LEDs. This is useful for various applications like particle (i.e. smoke) detection, proximity measurements, and even photoplethysmography. To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
product
SparkFun GPS Breakout
NEO-M9N, Chip Antenna (Qwiic)
The SparkFun NEO-M9N GPS Breakout with on-board chip antenna is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations witn ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
16 Channel 12C Relay Expansion
FXA-105 I2C Relay 16CH
The FXA-105 provides sixteen I2C controlled relays. It is equipped with a wide range 7V to 24V power supply and based on a 16bit I2C Port Expander (PCA9535). To simplify debugging each channel is equipped with a status led. In addition, it is delivered with an installed DIN rail carrier.
-
product
SparkFun Qwiic Thermocouple Amplifier
MCP9600 (Screw Terminals)
The MCP9600 Breakout is a high accuracy Thermocouple Amplifier equipped with an I2C interface, accessed over our Qwiic system. Inside the chip are two temperature sensors, one for the thermocouple itself (the hot junction) and one for the chip itself (the cold junction). As a result, the MCP9600 can read both the ambient temperature and the temperature of whatever you're trying to measure! The MCP9600 can do both with a resolution of 0.0625°C, and an accuracy of ±1.5°C (worst-case). The MCP9600 Thermocouple Amplifier is one of our many Qwiic compatible boards! Simply plug and go. No soldering, no figuring out which is SDA or SCL, and no voltage regulation or translation required!
-
product
SparkFun Qwiic Single Relay
Have you ever wanted to control something powerful or have you ever needed to turn on/off a high power device from your Arduino or another low powered microcontroller? The SparkFun Qwiic Single Relay provides you with the easiest to use relay yet. The Single Relay board can handle up to 5.5A at 240VAC for long periods of time and allows you to control large power loads with simple I2C commands. Utilizing our handy Qwiic system, and on-board screw terminals, no soldering is required to connect it to the rest of your system!
-
product
SparkFun Qwiic EEPROM Breakout
512Kbit
The SparkFun Qwiic EEPROM Breakout is a simple and cost effective option to add some extra storage space to any project. With 512 kilo-bits (or 64 kilo-bytes) of storage, this product is great for any microcontroller that doesn't have any EEPROM storage space, like the SAMD21. You can use the Qwiic EEPROM for storing data like GPS waypoints and other user settings that need to be maintained between sketch uploads. The SparkFun Qwiic EEPROM has three address jumpers, allowing for up to eight EEPROMs on one bus. All communication is enacted exclusively via I2C, utilizing our handy Qwiic system (as the name implies). However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.
-
product
SparkFun LiPo Fuel Gauge
LiPo batteries are a great way to power your projects. They're small, lightweight, and pack a pretty good punch for their size. Unfortunately, even the best batteries eventually run low on power and when they do it's often unexpected (and at the worst time). Don't be caught by surprise next time your board suddenly powers-down! The SparkFun LiPo Fuel Gauge connects your battery to your project and uses a sophisticated algorithm to detect relative state of charge and direct A/D measurement of battery voltage. In other words, it tells your microcontroller how much 'fuel' is left in the tank. The LiPo Fuel Gauge communicates with your project over I2C and an alert pin also tells you when the charge has dropped below a certain percentage.
-
product
Qseven Rev 2.1 Application Board With LVDS, HDMI, Dual LAN And Audio
Q7B301
The Q7B301 is an ultra-compact Qseven reference carrier board which measures only 100 x 72 mm - the size is slightly bigger than a credit card. The Q7B301 is perfect for small box applications such as those found in the latest digital signs, kiosks and traffic control system. This Qseven application board offers various I/O connectors and flexible expansion features to reduce the design effort to the minimum. The Q7B301 also has an extended industrial grade operating temperature range of -40ºC to +85ºC to withstand the rigors of harsh environments. Axiomtek’s new Qseven Rev. 2.1 application board, Q7B301, is compatible with Qseven module – Q7M311 which is powered by the Intel® Pentium® Processor N4200 and Celeron® Processor N3350. Customers can emulate required functions on Q7M301 as a reference design board or integrate the Q7M301 directly into their product as the application board. Its minimum footprint also enables the maximum potential. The Q7M301 is especially suited for industrial IoT applications such as industrial control, medical imaging, digital signage, gaming machines, military, and networking. The Q7B301 comes with two PCI Express Mini Card slots and one SIM card slot for wireless communication (3G/4G, GPS, Wi-Fi and Bluetooth). For enhanced or high-definition audiovisual devices, the Qseven reference carrier board supports one HDMI and LVDS interfaces as well as HD audio and 4-channel digital I/O. More I/O interfaces include two Gigabit LANs with Intel® i211AT Ethernet controller, two RS-232/422/485, one USB 2.0, two USB 3.0, one SMBus, and one I2C. Furthermore, it has one SATA-600 interface for storage requirements.
-
product
SparkFun Spectral Sensor Breakout
AS7262 Visible (Qwiic)
The SparkFun AS7262 Visible Spectral Sensor Breakout brings spectroscopy to the palm of your hand, making it easier than ever to measure and characterize how different materials absorb and reflect different wavelengths of light. The AS7262 Breakout is unique in its ability to communicate by both an I2C interface and serial interface using AT commands. Hookup is easy, thanks to the Qwiic connectors attached to the board --- simply plug one end of the Qwiic cable into the breakout and the other into one of the Qwiic Shields, then stack the board on a development board. You’ll be ready to upload a sketch to start taking spectroscopy measurements in no time.
-
product
Mixed Signal Oscilloscopes
A Mixed Signal Oscilloscope (MSO) is a combination Logic Analyzer and Oscilloscope. Since all inputs sample simultaneously, it is easy to see the timing relationships of the digital and analog components of your circuit. The extra channels also allow for more complex triggering. All of our MSOs have Oscilloscope triggering, Logic Analyzer triggering, SPI triggering and I2C triggering.
