I2C
IC serial bus protocol speed grades; standard mode: 0.1 / 0.4, fast mode: 1.0 / 3.4 / 5.0 Mbit/s are maximum ratings. Also known as: Inter-Integrated Circuit
See Also: Serial, Serial Communications, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus
-
Product
SIMRC - 8 x 2 Matrix 2-Pole
1030-R-8-2-2-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
SparkFun Distance Sensor Breakout
4 Meter, VL53L1X (Qwiic)
-
This SparkFun Distance Sensor Breakout utilizes the VL53L1X next generation ToF (Time of Flight) sensor module to give you the highly accurate measurements at long ranges for its size. The VL53L1X from STMicroelectronics uses a VCSEL (Vertical Cavity Surface Emitting Laser) to emit an Infrared laser to time the reflection to the target. That means that you will be able to measure the distance to an object from 40mm to 4m away with millimeter resolution! To make it even easier to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system so no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1”-spaced pins in case you prefer to use a breadboard.
-
Product
SIMRC - 16-Channel 2-Pole Multiplexer
1020-R-16-2-5/1D
Multiplexer Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Engine Control
StepGenerator4
-
*4-axis stepper motor control *Clock and direction signals *Speed up to 100,000 steps / s Positioning range +/- 2,147,483,647 steps *Simple ASCII commands via the serial interface *I2C adapter (master) for controlling external actuators / sensors *40-pin DIP package PCB (600mil / 19mm x 52mm).
-
Product
Grid-EYE® Infrared Array Sensors
-
Panasonic Industrial Devices Sales Company of America
Panasonic Grid-EYE® is an 8x8 (64) pixel Infrared Array Sensor. This Sensor offers digital output (I2C) for thermal presence, direction, and temperature values. The built-in lens includes a 60-degree viewing angle. Grid-EYE features compact SMD design using MEMS thermopile technology.
-
Product
Bus Analyzer, Monitor, Debugger & Programmer
BusPro-I™
-
The BusPro-I has all the power, flexibility, and features you need to monitor and debug the I2C bus circuitry on your board. The BusPro I2C can be used to monitor and log I2C bus traffic in real-time, generate I2C transactions to communicate with peripheral components on the bus, and in-system program I2C compatible EEPROMs.
-
Product
Multibus Ethernet Card
MS 1750
-
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz- SDRAM Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Multibus Interface- Serial Interfaces: Up to four external UARTs- CAN 2.0B controller- Three I2C ports- Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements
-
Product
SparkFun Altitude/Pressure Sensor Breakout
MPL3115A2
-
Life has its ups and downs, so why not measure them? The MPL3115A2 is a MEMS pressure sensor that provides Altitude data to within 30cm (with oversampling enabled). The sensor outputs are digitized by a high resolution 24-bit ADC and transmitted over I2C, meaning it's easy to interface with most controllers. Pressure output can be resolved with output in fractions of a Pascal, and Altitude can be resolved in fractions of a meter. The device also provides 12-bit temperature measurements in degrees Celsius.
-
Product
Mission Processor
58U91-03
-
- +28 VDC input- 9 DC outputs at 600 Watts- Provides system EMI per MIL-STD-461- Continuous Background Built-In-Test (BIT)- Temperature monitoring- I2C communication
-
Product
SparkFun GPS Breakout
NEO-M9N, Chip Antenna (Qwiic)
-
The SparkFun NEO-M9N GPS Breakout with on-board chip antenna is a high quality GPS board with equally impressive configuration options. The NEO-M9N module is a 92-channel u-blox M9 engine GNSS receiver, meaning it can receive signals from the GPS, GLONASS, Galileo, and BeiDou constellations witn ~1.5 meter accuracy. This breakout supports concurrent reception of four GNSS. This maximizes position accuracy in challenging conditions, increasing precision and decreases lock time; and thanks to the onboard rechargeable battery, you'll have backup power enabling the GPS to get a hot lock within seconds! Additionally, this u-blox receiver supports I2C (u-blox calls this Display Data Channel) which made it perfect for the Qwiic compatibility so we don't have to use up our precious UART ports. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
Product
Bridge Device and GPIO Port Expander
SPI-to-I2C
-
The CP2120 compact SPI-to-I2C bridge and general purpose port expander device can be easily added to a system to solve interface compatibility problems and add more GPIO when required.
-
Product
Smart Card Reader
UTC-510P-S01E
-
Memory card -Synchronous 2-line, 3-line and I2C interface. CPU card -Complies with ISO7816-1,2,3,T=1 and T=0 protocol. Reliability: 200,000 cycles.
-
Product
Silicon Oscillators
-
Analog Devices silicon oscillators are frequency programmable via pin-strapping, or through the resistor connection or serial interface (SPI or I2C). These solid-state clocks are well-suited for general-purpose usage, such as PGAs, ASICS, microprocessors, or UARTS, and they operate from 1 kHz to 170 MHz. Silicon oscillators are also ideal switching regulator clocks as they provide synchronization and EMI reduction (via spread spectrum).
-
Product
Lightning "Emulator" Shield
SEN-39002
-
Arduino shield, ideal for AS3935 lightning sensor development. The lightning "emulator" generates a RF signal that mimics lightning strikes. This board is in an Arduino Uno form factor, and only uses GPIO and I2C, so can be stacked on many form factors (developed on an Uno and Mega).
-
Product
Multi Protocol Analyzer
LE-2500R
-
LE-3500R/LE-2500R adopted TTL port as its standard besides RS-232C, RS-422, and RS-485 while having the same feature such as small and light body of LE-3500/LE-2500. You can monitor I2C or SPI without expansion board.
-
Product
SparkFun Triple Axis Accelerometer Breakout
ADXL345
-
This new version adds two standoff holes as well as an extra decoupling capacitor. The ADXL345 is a small, thin, low power, 3-axis MEMS accelerometer with high resolution (13-bit) measurement at up to +-16 g. Digital output data is formatted as 16-bit twos complement and is accessible through either a SPI (3- or 4-wire) or I2C digital interface.
-
Product
Evaluation Kit
ROM-3310 Development Kit
-
*Evaluation kit for ROM-3310*Lower power TI sitara AM3352 1GHz processor*On board DDR3 512MB memory / 4GB Flash*HW WDT for system protection*Supports 1 GbE, 1 USB 2.0, 1 USB 2.0 OTG, 2 CANbus, 10 GPIO, 4 UART,1 I2C, 1 I2S, 1 SPI, 1 SDIO*Cable pack & Panel included*Evaluative image & test utilities built-in
-
Product
I2C Bus Monitor - USB
Model JI-216
-
The JI-216 I2C Bus Monitor is a low cost, easy-to-use PC hosted instrument specificallydesigned for troubleshooting and debugging I2C networks. The JI-216''s FPGA basedarchitecture provides for the capture and display of all valid or invalid messages and I2Cbus events. Captured I2C messages are available for display in two modes: real-timestreaming, or triggered. These modes provide optimized data display for either hardwareor software development. The SDA/SCL timing display aids in tracking down and solvinghardware timing problems. JI-216''s broad bandwidth (DC 3.4Mbits/s), wide input signalrange (0 15.0V), and variable signal filtering provides flexibility in monitoring a variety ofI2C bus systems. An intuitive Windows application manages instrument setup andcontrol. Communications and unit power is provided via a USB 2.0 link.
-
Product
SIMRC - 16 x Uncommitted Reed Relay, SPST
1010-R-16-1-5/1D
Reed Relay
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Dual Band Block Up-Converter
DBUC Series
-
*Connectorized Package *Wide Choice of Frequency Ranges *Dual Band *Integrated Filters *Gain Control *CAN, RS-232, I2C, or SPI Control *Internal / External References *Low Power Consumption *Low Phase Noise *Low Spurs
-
Product
SIMRC - SMB RF Adapter PCB
1092-001
-
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
ST VL53L0X Time-of-Flight Range/Distance Sensor
SEN-36003
-
Highly integrated breakout board for the ST Micro VL53L0X Time of Flight (ToF) range finder sensor, which builds on the absolute ranging technology introduced with the VL6180X. The VL53L0X drops the ambient light sensing capability of it's predecessor for a 10X improvement in absolute ranging capability, bringing the maximum possible range to 2 meters! As a result, this sensor has even more uses in the robotics, cell phone and gesture recognition space. The SEN-36003 includes the VL53L0X IC mounted between two 4-40 sized mounting holes with on board 2.8V LDO and high-speed signal translation to handle interface voltages from 3V to 5V. The board is interfaced via an I2C interface and function pins have been broken out to a 0.1" pin header. All pins are translated to allow interfacing with any microcontroller in the 3V to 5V operating range.
-
Product
SIMRC - 8-Channel 1-Pole Multiplexer
1020-R-8-1-5/1D
Multiplexer Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
Module Spectrum
nRF52820 Series
-
Nordic nRF52820 solutioin features an Arm Cortex-M4 processor with 256 KB Flash and 32 KB RAM. Supports SPI, UART, I2C and USB interfaces
-
Product
USB to I2C Adapter
Model JI-300
-
The JI-300 is a versatile, easy to use PC hosted adapter used to drive I2C communicationsto/from a target device. The desktop unit can be configured to interface a variety of I2Cnetworks. Bus parameters such as clock frequency, duty-cycle, setup and hold times, busvoltage, and pull-up resistor values can be varied. JI-300''s diagnostic features including"excessive clock-stretch", "bus-not-free", and "bus contention" monitoring, as well as statusreporting at the conclusion of each message transaction simplifies I2C trouble-shooting. AWindows software application manages the setup and control of the instrument.Communications and unit power is provided via a USB 2.0 connection.
-
Product
Temperature, Humidity, Pressure and Gas Sensor
BME680
-
The BME680 is a digital 4-in-1 sensor with gas, humidity, pressure and temperature measurement based on proven sensing principles. . This little sensor contains temperature, humidity, barometric pressure, and VOC gas sensing capabilities. All over SPI or I2C at a great price!
-
Product
400 Watt DC/DC Converter, 3U VPX, Holdup Time
VPX68
DC Converter
NAI's VPX68 is a rugged and high-efficiency 400-Watt Output +28 VDC Input 3U VPX DC/DC converter designed for aerospace, defense, and industrial markets. It is an off-the-shelf power supply with optional integrated Holdup Time that plugs directly into a standard VITA 62 conduction cooled chassis. The power supply, engineered to meet harsh environmental conditions, includes continuous Background Built-In-Test (BIT), I2C communication, remote error sensing, and protection against Input transients, over-voltage, over-current, and short-circuits, ensuring reliable and consistent performance.
-
Product
Quad QSFP28/QSFP+ FMC+ Module
FPGA Board
iWave’s QSFP28/QSFP+ 2×1 Stacked FMC+ HSPC Module is designed to meet VITA 57.4 FMC+ Standard. This FMC+ Module is supported by two stacked QSFP28/QSFP+ ports(Upto400G) with 4-Bit Silicon Labs programmable clock synthesizer (default = 156.25Mhz). A flexible reference clock for on the QSFP28/QSFP+ 2×1 Stacked FMC+ Module is fully programmable over the 0.16 to 710 MHz range through I2C. Each QSFP28/QSFP+ ports are directly connected to four multi-gigabit serial transceivers banks of Vita 57.4 compliant carrier Board.
-
Product
Module Spectrum
nRF52833 Series
-
Nordic nRF52833 solutioin features an Arm Cortex-M4 processor with 512 KB Flash and 128 KB RAM. Supports SPI, UART, I2C,I2S, PMD, PWM, ADC, NFC and USB interfaces
-
Product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
-
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
