Wire
See Also: Contacts, Harness, Connectors
-
Product
HART Protocol Stack
softHART
-
SoftHART is the industry-standard smart HART (Highway Addressable Remote Transducer Protocol) communications stack for industrial automation. HART is a bidirectional protocol and communicates over existing 4-20 mA analog current loops, extending communication capabilities without the inconvenience of installing additional wiring.
-
Product
3 Ft Harness, 78-Pin Male Connector On One End, Loose Wired (Numbered) Other End
GT97102
-
3' harness, 78-pin male D-sub connector on one end, loose wired (numbered) other end.
-
Product
Analog I/O Modules
-
The AMAX-4800 series analog I/O modules offers channel-independent configuration, signal type selection, and sensor wiring burn-out detection.
-
Product
9050 VXI - 50 Module Solution for VXI cards
-
The 9050 VXI Solution is designed for use with VPC's pre-wired interconnect adapters on the top tier and discrete wiring modules on the bottom tier. The receiver opens downward via hinges to give the user access to the instruments in the rack. A microswitch, which comes standard, allows for shut off any power going through the system before removing the ITA. Using a plug and play plate or a flange kit allows for easy mounting of the receiver to any 19” rack system.
-
Product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Cut Ends
A050DM5-C-0A050
Cable Assembly
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
G12x Slide Mount
-
For maximum versatility and easy access to instrument-side wiring and cable assemblies, VPC offers a selection of slide kits designed to fit most common rack depths. The G12x uses the same platform and slides as the G12, providing support up to 180 lbs (81 kg) to accommodate the largest fixtures. G12x accepts ITAs designed for both the G12 and G12x.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs
510140111
Pull-Thru Adapter
Pull-Thru Adapter, Wired, TriPaddle, 2 FML 9 Pin D-Sub, 2 SMB Plugs.
-
Product
Dual Mobile Communications DC Source w/ DVM
66309D
DC Power Supply
The Keysight Mobile Communications DC Source 663xx series offers several features ideal for testing wireless and battery powered devices. Excellent voltage transient response ensures maximum test-system throughput by minimizing device shutdowns due to significant voltage drops in the test wiring. Built-in advanced measurement system to accurately measure battery current drains when the device operates in different modes and a Keysight-developed feature that enables cellular telephone manufacturers to detect permanently and intermittently open-sense wire connections.The Keysight 66309D dual output mobile communications dc source provides two outputs for testing both the main battery power and the battery charger circuitry, allowing customers to test phones and chargers with the same equipment. This feature helps save on rack space (2 outputs in a half rack box) and eliminates the need for two separate power supplies.The 66309D dc source provides all of the capabilities of the 66309B with the addition of a built in digital voltmeter.
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Female, 0.5m, 45º
A1604F5-1604F5-0A050
Cable Assembly
For applications where a 45 degree cable exit would be preferred. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connectors to have a second fixing then the connector can be fitted with the optional screwlock assembly 40-969-101 where applications permit.
-
Product
Shore A Type Hardness Tester Rubber Hardness Tester
HS-A
-
Shenzhen Chuangxin Instruments Co., Ltd.
HS-A is a digital Shore A type hardness tester. It is suitable for plastic (such as film, medical appliance, etc.), synthetic rubber(such as seals, tires, rubber roller, rubber hose/belt, wire and cable, shock absorber, etc.) and other related chemical products.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 1m, Screwlocks
A068SMR-T-6A100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
Product
BNC (M) To Multi-Stacking Banana Plugs
3957
-
BNC (m) to multi-stacking banana plugs. Converts BNC (Female) cables/connectors to top/side stackable banana plugs for test versatility. BNC connector and banana plugs are molded directly to the wire for pull strength durability anddust/moisture resistance.
-
Product
Line Tester
CAT 1 TEST
-
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
Product
Voltage Detectors & Testers
-
Non-contact AC voltage detector quickly checks for the presence of live voltage on wiring and electrical devices. Features a built-in flashlight for added convenience.
-
Product
Analog Control Cable for Electronic Loads
EE105T-xx
-
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
Product
MS-M 3-Pin RF Cable Assembly, Female to Unterminated, 0.5m, RG178 Cable
40-979A-503-0.5m-FU
RF Cable Assembly
This 0.5m long MS-M RF 3-Pin cable assembly is constructed from RG178 Silver Plated Copper Clad Steel Wire with FEP insulation and an attenuation of 102dB/100m at 500MHz. Screwlocks are provided to secure the MS-M connector to the associated product.
-
Product
LCZ LCR Meter
SS1061
-
LCZ Meters are a test system for passive components designed for the use in electronic inspection or production process for quality control. They meet any demanding requirement on production speed and precision, discrimination of qualified products from unqualified ones, as well as internal setup, storing and calling function for up to 10 instrument groups, so they are actually optimum test instruments for component incoming and production inspection. Like as: transformer, inductor, resistor, capacitor, relay, motor, generator, eletric valve, contactor,cable,wire,etc.
-
Product
Gauge Type T Thermocouple Wire
W-TW-36P2
-
Most thermocouple wire used in the manufacture of sensors is "Special Limits" wire which, to meet NIST standards, must be accurate to 0.5°C in the range 0-50°C. This means that even with most sophisticated electronics, the best possible accuracy for the system is 0.5°C.
-
Product
Vertical Hinged Mounting Frame, ICon, 5U, 3 Positions
310113463
Mounting Frame
The 5U Vertical hinged Mounting Frame mounts to standard 19" racks and hinges open to allow access to wiring between the instruments and VPC Receiver. The 3 cutouts are spaced evenly across the panel. iCon cover plate sold separately (310 113 467).
-
Product
20-Pin GMCT Cable, Female to Unterminated, Cut Ends, 10A, 2m
A020GFR-C-0C200
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
Extension Wires And Cables
-
Omega offers thermocouple, RTD and thermistor extension wire and cable. We offer a wide variety of calibration, gauges, sheath material, insulation, connector types and shapes.
-
Product
Multi-Modular Cable Tester
3PK-NT005N
-
Multi-modular cable tester is applied to quickly test by auto scanning most of modular cable, USOC 4 / USOC6 / USOC 8 terminating with RJ 45, RJ12, and RJ11 modular plug, wires continuity and miss-wiring.It can be also used for testing the cable is crossed pinning or straight through. Moreover, with the remote terminator, it can be further used in remote testing even the cable has been already installed.
-
Product
Instrument Grade Data Sensor
WISER 8000
-
TECAT Performance Systems, LLC
The TECAT WISER Model 8000 dual strain measurement and monitoring system is a wireless data acquisition system for measuring two external strain channels at high data rates up to 8kHz. The small, light, power-efficient, and non-invasive design enables strain measurements in a wide range of applications. With dual external sensor inputs two Micro-Measurements strain gauge bridges can be measured by a single system, for example to measure both thrust and torque loads simultaneously.The Model 8000 has a long range data transmission of >1,000 meters with up to +/- 0.025% FSR sensitivity for remote measurements. After initial setup using the WISER software interface, the system can be wired directly to your DAQ system, for seamless data collection.
-
-
Product
50/75 Ohm Micro Coax Contacts
-
Rated to 3 GHz using RG 316 or RG 178 Max of 10.5 GHz using RG 316 Double Shield.Rated to 10,000 cycles.50 and 75 Ohm impedance.Mating force of 1.5 lb.High density I/O Crimp contact designed for RG 316, RG 178, and RG 179 wire.
-
Product
Level System
Universal II
-
The Universal II level transmitter offers increased reliability, low maintenance and an intrinsically safe design for dependable level measurements in all kinds of process liquids, slurries, granulars and interfaces.Universal IIThe Universal II is a two wire level transmitter that eliminates the need for line power in the field and saves costs for additional hardware. It provides reliable level measurements in all kinds of process liquids, slurries, granulars and interfaces.When powered from an approved source this level transmitter can be made intrinsically safe. Its rugged contruction resists corrosion and abraision. The no moving parts design eliminates break downs.The Universal II level transmitter utilizes RF Admittance technology with manual calibration and a 4 – 20 mA output signal. The patented Cote-Shield circuitry ensures accuracy and reliability regardless of product build-up on the level transmitter.This level system is unaffected by changes in the process material density, pressure, or temperature variations.
-
Product
Cable Tester
SS8681 Series
-
The SS8681 series cable tester is used for test and measure wire cable harness, wire harness, like as: auto cable, audio cable, power cable, network cable, telephone cable, USD cable, HDMI cable, video cable, etc.
-
Product
Test Adapter
cPCI/VME/VME64x
-
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
Product
Coil-on-Plug Spark Tester
TH458
-
For ignition systems with coil-on plugs, including Ford, Chrysler, Chrysler imports, Mitsubishi, Nissan, and more. Since coil-on plug ignitions do not have plug wires, inductive test equipment cannot be used. Spark tester tests for no-start conditions and measures coil output.
