-
product
Capacitance Bridge
1621
The GenRad1621 Capacitance Measurement system is a completely self-contained system capable of capacitance measurements in increments as small as 0.1 aF (10-4 pF) and conductance measurements in increments as small as 100 aU (10-7 U; equivalent to a shunt resistance of 1010 M). Measurements are three terminal, with 2- or 3-terminal connection, and provision is also made for the connection of an external standard for comparison measurements.
-
product
RM-24999, 96-Pin Female DIN to 10-Pin Female RJ50, Rack Mount Terminal Block
785840-01
96-Pin Female DIN to 10-Pin Female RJ50, Rack Mount Terminal Block - The RM-24999 provides RJ50 connectivity in a 1U rack-mount form factor for up to three bridge input modules. You can use SH96F-96M-5 Sensor Cables to connect to the PXI Express bridge input modules.
-
product
Connector Test
A connector test system which provides expansion of up to 160 Kelvin pair connections. The system incorporates high voltage AC and DC power supplies with a maximum output of +/- 2100 Volts peak for Hi Pot, Insulation resistance measurement. LCR bridge control is provided with 4 terminal multiplexing in order to add precision capacitance, inductance and resistance measurement capability. An integral H.V. capacitor bias option permits capacitance measurement to be made at up to 2.1kV.
-
product
FD-11637, 8-Channel Strain/Bridge Input Device for FieldDAQ
785641-01
8-Channel Strain/Bridge Input Device for FieldDAQ - The FD-11637 can measure eight channels and has built-in bridge completion and voltage excitation to support for quarter-, half-, and full-bridge sensors. It also features anti-alias filtering, offset nulling, and shunt calibration to reduce the effect of noise and improve measurement accuracy. The FD-11637 has an ingress protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 grm vibration. The FD-11637 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11637 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11637 is ideal for test cell and outdoor environments.
-
product
PXI-2722,16-Bit, 5-Channel PXI Programmable Resistor Module
781985-22
16-Bit, 5-Channel PXI Programmable Resistor Module—The PXI‑2722 is a test module that replicates the behavior of resistance-based inputs and outputs such as potentiometers, resistance temperature detectors (RTDs), voltage dividers, and bridge elements. The PXI‑2722 programmatically controls a series of relays to vary the resistance across each channel of an I/O connector. This function is well suited for simulating environmental conditions in hardware‑in‑the‑loop (HIL) validation. The software provides a simple user interface that accepts inputs in units of temperature or resistance and configures the resistance across each channel.
-
product
CompactPCI
cPCI4IP
The cPCI [CompactPCI] compatible cPCI4IP design adds 4 Industrypack compatible slots to your cPCI host. The cPCI4IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI4IP is a 6U 4HP cPCI design with 4 IP slots.
-
product
PMC Module Carrier
SK1-CHORD
SK1-CHORD is equipped with a PCI Express® to PCI® bridge for conversion of data from the CompactPCI® Serial backplane, to the on-board PCI® parallel bus.
-
product
Automation Software For Aim-TTi Power Products Including LD And LDH Series Electronic Loads.
Test Bridge
Test Bridge software is a simple Windows application intended to make it possible to create a test sequence that can control up to four Aim-TTi products and record measurement results in graphical and tabular form.
-
product
Standard Capacitors
1408 Series
Ultra-high stability. The continuously improvingaccuracy of capacitor calibrations by NISTbrings a better knowledge of capacitance tostandards laboratories - provided, of course,the laboratories have adequate referencestandards. The 1408 Reference Standard Capacitors,with their high stability, are suitablefor calibration in parts in 107. The 1616 PrecisionCapacitance Bridge is highly recommendedfor accurate calibration of a wide range ofworking standards from such a reference.
-
product
VME64 to USB 2.0/Optical Link Bridge
VX3718
The VX3718 is the new VME to USB 2.0/Optical Link Bridge that fully replaces the VX1718 (VME-USB) and V2718 (VME- CONET) models. The Bridge Implements a VME master controlled by a PC via USB 2.0 and Optical Link (CAEN CONET protocol) including all the functions of its two predecessors in a unique device.
-
product
200 Ampere Micro OHM Meters
HL-200
Measuring the line loop contact resistance by bridges is not the ideal method as the test current is only a few milli amperes. Thus the value is not the true value of the contact resistance. Model HL- 200 is a direct reading tester, and uses a test current of 200A DC, resulting in true value and accurate measurements. Model HL- 200 adopts digital circuit technique and is used for measuring contact resistance of switch control equipment at test current of 200A DC. The measurements are accurate as the test is highly stable. HL- 200 is a new, fully automatic micro controlled tester that measures contact resistance at 200A DC with built in printer.
-
product
PMC to PCI Express Adapter w/ TSI384
8636
The Technobox, Inc 6083 4-lane and 8638 1-lane carrier card allows use of a PMC in a PCI Express edge card slot. The product features an IDT TSI384 bridge IC used in transparent mode with a PCI Express primary side and a PCI/PCI-X secondary side.
-
product
Conversion Devices and Adapters
Conversion devices and adapters fulfill several roles. For example, you can use them to convert an output signal to a signal type that can be measured by a data logger, to adjust resistive bridge measurements, or to build distributed measurement networks.
-
product
Strain Measurements and Experimental Stress Analysis
Experimental structural testing using strain gauges is necessary in a wide range of applications from airframes and sub-assemblies down to individual components such as turbine blades, satellites, wind turbines, buildings, bridges and many others. These tests enable the engineers to compare the acquired data with the predicted results from the design calculations.
-
product
Load Cell Amplifiers
Datum Electronics load cell amplifier range is designed to increase (or amplify) a signal, generated by a strain gauge load cells with a full bridge connection, pressure transducers or torque sensors, allowing the user to use the data from the load cell in a more efficient and productive way.
-
product
Half, Full Bridge & Three Phase Drivers
Renesas' half-bridge (h-bridge), full-bridge and three-phase drivers handle voltages up to 100V, with industry-leading gate rise and fall times and exceptional input-to-output propagation delay performance.
-
product
Decade Capacitor
GenRad 1423-A
The GenRad 1423 decade capacitor is a versatile tool for calibration laboratories and production-line testing. With it a bridge can be standardized to an accuracy exceeded only by that of the highest quality, individually certified laboratory standards such as the GR 1404 Reference Standard Capacitors.Used with a limit bridge, such as the GR 1689 Digibridge, the 1423 facilities fast and accurate production-line measurements of arbitrary capacitancevalues with minimum setup time.
-
product
20-slot ATX-supported Bridged PICMG Bus Active Backplane
ATX6022/20GP18
*1 PICMG, 18 PCI and 1 ISA*Compatible with AX61492 chassis*Supports both AT and ATX power supply
-
product
Circuit Module, Riser for ISMB, PCIex4 to 3 PCI A201,RoHS
AIMB-R430P-03A2E
- Connecting Interface: PCIe x4- Expansion Slots: 3 x 32-bit/33 MHz PCI- PLX PEX_8111BB PCIe to PCI Bridge
-
product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
product
Resistance Bridges - AccuBridge® Line
Measurements International Ltd.
The Resistance Ratio Bridge from Measurements International is the next generation replacement. Measurements International is pleased to release the next generation room temperature Direct Current Comparator Resistance Ratio Bridge.
-
product
PCI CONET Controller
A2818
The Mod. A2818 is a 32-bit 33 MHz PCI card, which allows the control, through a standard PC, of up to 8 CAEN Optical Slave Cards (CAEN VME Bridge or Digitizers). The communication protocols used are the CONET1 or the new CONET2 (A dedicated firmware for the desired protocol must be installed on the board).
-
product
Low-Power Ethernet Bridge Converter for MIL-STD-1553 and ARINC
eNetX-MA4
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
product
SparkFun Dev Board
AST-CAN485
The SparkFun AST-CAN485 Dev Board is a miniature Arduino in the compact form factor of the Pro Mini. In addition to all the usual features that a mini Arduino has, it possesses an onboard CAN (Control Area Network) and RS485 ports, enabling quick and easy interfacing to a multitude of industrial devices. The CAN485 Dev Board bridges the gap between the maker and industrial spaces!
-
product
Compact PCI
cPCI2IP
The cPCI [Compact PCI] compatible cPCI2IP design adds 2 Industrypack compatible slots to your cPCI host. The cPCI2IP acts as an adapter, converter, carrier, or bridge between the cPCI bus and your IndustryPack hardware. The cPCI2IP is a 3U 4HP cPCI design with 2 IP slots.
-
product
CompactPCI 6U 14 Slot, P1-2s, P3-5l, 3 X P47 + Bridge
103CPCI614-9001
CompactPCI 6U 14 slot with bridge 64 bit Easyplug with 3 x P47 power connector, system slot left, fully compliant to the PICMG basic specification 2.0 R3.0 and Hot Swap specification 2.1 R1.0.
-
product
PMC-to-PCI Express Adapter
4733
The Technobox, Inc. P/N 4733 PMC-to-PCI Express Adapter permits the use of a single-wide PMC module in a 4X PCIe slot. The product features a PEX8114 bridge running in transparent mode. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card. 64-bit support.
-
product
X-Ray Inspection System
MX1
Manncorp’s new MX1 is a high-performance x-ray inspection system designed for real time imaging of multilayer PCBs and dense metal BGAs, μBGAs, and chip scale packages. Its high voltage (80kV), computer-controlled x-ray tube and 35 μm focal spot provide the power necessary for detection of a variety of defects including bridging, voids, and missing balls. The MX1’s standard camera features continuous zoom magnification from 4X to 50X and variable angle viewing up to 45°, and an upgrade to the x-ray tube can boost magnification to 225X.
-
product
Transformer Testing
Measuring bridges or electronic burdens can be individually integrated into existing CT/VT test systems. Customized solutions are our core competence.
-
product
Interface Adapter. USB Solution
U2C-11
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
