-
Product
Temperature Calibration
-
Process Instruments maintains primary temperature standards for the calibration of Standard Platinum Resistance Thermometers. SPRT''s are measured against a Thomas-type Ten Ohm Standard Resistor (a Leeds & Northrup 4211-B), using a Measurements International automated bridge. Primary thermometry points are maintained at the Water, Tin, Zinc and Gallium points.
-
Product
Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier
6332
-
Our Dual-Site Single-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier 32-Bit/66 MHz (6332) adapts two single-wide PMCs to a cPCI slot. At the heart of the carrier is a 6150 PCI-to-PCI bridge that connects the carrier's internal PCI bus to the cPCI backplane.
-
Product
Precision Temperature Bridges - AccuBridge® Line
-
Measurements International Ltd.
Multiple Display Modes Including: Temperature (°C, K, °F), Resistance, Ω, Ratio, ADCC Technology, Accu-T-Cal™ Software (NMI Designed).
-
Product
CompactPCI Instruments
-
Is a computer bus interconnect for industrial computers,combining a Eurocard-type connector and PCI signaling and protocols. Boards are standardized to 3U or 6U sizes, and are typically interconnected via a passive backplane. The connector pin assignments are standardized by the PICMG US and PICMG Europe organizations. The connectors and the electrical rules allow for eight boards in a PCI segment. Multiple bus segments are allowed with bridges.
-
Product
SparkFun Dev Board
AST-CAN485
-
The SparkFun AST-CAN485 Dev Board is a miniature Arduino in the compact form factor of the Pro Mini. In addition to all the usual features that a mini Arduino has, it possesses an onboard CAN (Control Area Network) and RS485 ports, enabling quick and easy interfacing to a multitude of industrial devices. The CAN485 Dev Board bridges the gap between the maker and industrial spaces!
-
Product
Memory And Storage
-
Intel provides technically advanced products that support every level of computing—from data center workloads to enthusiast usage. Intel® Optane™ memory creates an accelerated bridge between memory and storage. Intel® Solid State Drives (Intel® SSDs) provide storage flexibility, stability, and efficiency.
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Strain Sensors
-
Conventional strain sensors are based on strain gage technology. In order to effectively measure the strain values in a force or load measurement application, a full, 4 element strain gage bridge circuit is utilized. The configuration is known as a Wheatstone Bridge Circuit. A Wheatstone Bridge has a very linear output in it’s midrange. That being considered +100% to -100% of range. Unfortunately, a Wheatstone Bridge becomes non-linear above the upper and lower extremes of range. Therefore, significant errors can result above the end points when attempting to take precision measurements. It is particularly important to take accurate measurements in some R&D or control applications. To avoid the mentioned error issues, PCB manufactures quartz piezoelectric strain sensors that output the same mV/microstrain sensitivity throughout the entire useful range. Thus, accuracy is improved and control requirements are enhanced that may occur at positive extremes of the measurement range. The models RHM240 and model 740B02 series sensors are the strain sensors for these applications.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-01
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Pressure, Strain And Shock Data Loggers
-
Dataloggers for pressure, bridge input for strain or load measurement and also tri-axial shock dataloggers with built in accelerometers.
-
Product
Cockpit Software for Vision Analyzers
-
COCKPIT™ offers the utmost in flexibility. Lab managers use the PC software for Vision analyzers to consolidate measurement results and statistics from multiple locations in one central lab. By taking advantage of a direct Ethernet or a LIMS-connection, COCKPIT™ builds a bridge between the lab and Grabner vapor pressure testers in the field. Access via VPN tunnel adds an extra layer of security to the data transfer between Vision analyzers and COCKPIT™ software.
-
Product
Ethernet Bridge Converter for MIL-STD-1553 and ARINC
ENETX-MA4
Ethernet Interface
eNetX-MA4™ is an innovative product for “remoting” 1553 & ARINC-429/717 operations on 10/100/1000 Ethernet local area networks (LAN). eNetX-MA4 is a very small, low-power, rugged device that provides real-time UDP connectivity to for 1-2 dual redundant 1553 (A/B) busses and 4 ARINC channels. Tested to MIL-STD-704F/810G/461F and DO160.
-
Product
Strain Gauges
TSM
-
We have been designing and manufacturing strain gauges for over 50 years and one of the earliest members of the British Society for Strain Measurement: Linear Strain, Dual Strain, Full & Half Bridge, Rosette & Circular, Bonding Services, Torque & Shear Strain Gauges and Bi-Axial/Tri-Axial Strain Gauges.
-
Product
Five-Site Dual-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier
6567
-
Our Five-Site Dual-Slot 6U Compact PCI (cPCI) PMC Adapter/Carrier 32-Bit/66 MHz (6567) adapts five single-wide PMCs to a cPCI slot. At the heart of the carrier is a 6150 PCI-to-PCI bridge that connects the carrier's internal PCI bus to the cPCI backplane.
-
Product
Radio Telemetry
-
Procter & Chester Measurements Ltd
Radio Telemetry: A transmission of data from a remote source via a radio to a receiving station for recording and analysis.Inductance: A contactless method of supplying power to (in this case) a strain gauge bridge. The signal is then transmitted back to the electronics.Slip Ring: Consists of a conductive band mounted on a shaft and is insulated from it. The wheatstone bridge is connected to the bands (usually four off). Fixed brushes or contacts make contact on to the bands to transfer power to the bridge and signal back to the static instrumentation.
-
Product
Automation Software For Aim-TTi Power Products Including LD And LDH Series Electronic Loads.
Test Bridge
-
Test Bridge software is a simple Windows application intended to make it possible to create a test sequence that can control up to four Aim-TTi products and record measurement results in graphical and tabular form.
-
Product
RTD Data Logger
-
RTD Data Logger is the most commonly used sensors for measuring temperatures in various industries. These are positive temperature coefficient resistive sensors and Pt100 is the most commonly used type of RTD sensor which has 100 ohm resistance at 0 C. IM2000 series RTD data loggers offer bridge measurement technique to compensate for effect of wire length. In addition logger has facility to program offset so that the measurements are more accurate.
-
Product
6U Processor Board
CP62103
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62103 is a modular design, based on COMexpress® technology, up to 4-core i7 processor from Intel® Ivy Bridge family. CP62103 is designed to meet harsh environment applications like rural communication, military, medical and outdoor video processing.CP62103 supports up to 3615QE, an Intel® 4-core processor. The 3rd generation Intel® Core™ i3/i5/i7 processors have a completely new microarchitecture, enabling small-sized designs to be created with unmatched computing power, graphics performance and energy efficiency on a small footprint.
-
Product
Resistance Bridges - AccuBridge® Line
-
Measurements International Ltd.
The Resistance Ratio Bridge from Measurements International is the next generation replacement. Measurements International is pleased to release the next generation room temperature Direct Current Comparator Resistance Ratio Bridge.
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
Ethernet to Wireless Bridge
BR-100AH
-
BR-100AH is the first commercially available bridge supporting IEEE’s 802.11ah wireless standard which is a long-range technology which enables any Ethernet device to become an 802.11ah wireless network device, giving the freedom to place it anywhere in your facility. BR-100AH is all that you need to incorporate your device into your 802.11ah (HaLow) network. A benefit of 802.11ah is extended range, making it useful for long distance and rural communications.
-
Product
Wideband Power Amplifiers
-
Krohn-Hite Wideband Power Amplifiers are designed to meet today's industrial needs where wideband, precision performance is required. Applications include: meter calibration, piezo transducer driving, bridging applications requiring high input and low output impedance, low distortion ac power source, ion beam deflection, vacuum tube driver, ink jet testing and design and many more.
-
Product
PCI To PCI Express Board
MS 1718
-
PCI to PCI Express card is used to extend PCI / PCI-X bus from one PCI system to another system over an optical fiber medium up to 500meters or over a copper medium up to 7 meters using a PCI express interface. This card receives/transmit PCI signals from/to the Host System. These PCI signals are converted into PCI Express using PCI / PCI-x to PCI Express cross bridge and vice versa. The PCI Express signal is transmitted / received through the optical interface or copper interface.
-
Product
Signal Conditioners
General Purpose
-
Encore offers a complete line of General Purpose Signal Conditioning instrumentation to meet even the most demanding requirements. Packaged as interchangeable two-channel plug-in modules, Encore’s broad product line includes frequency to voltage converters, strain gage amplifiers, accelerometer conditioners, digital voltmeters and DC power supplies. All of our systems feature a common CAL input on the rear of the rack which allows for calibration of the entire rack. Calibration function varies based on the modules installed. For example, the Model 633 applies a shunt calibration resistor across the bridge, while the Model 149 applies a reference charge source to the input. Contact Encore today and let our team of design engineers help you determine which of our products is best for your application.
-
Product
IRIG-B TTL TO RS485 Converter
SPC - INS - 1010
-
Signals & Systems India Private Limited
The IRIG-B TTL signal is a time synchronization protocol that can be transmitted up to 50m maximum using coaxial cable. So the relay which is to be received the IRIG-B TTL signal may be far away from the IRIG-B source. The relay may be not able to synchronize with the GPS. To avoid such an incident in the field, some of the relays have provision to receive IRIG-B RS485 signal. The IRIG-B RS485 signal can able travel up to 1200m without any booster. All Time source equipment may not be supplied with IRIG-B RS485 signal output. The converter will act as a bridge between GPS Time source and Relays for time synchronization.
-
Product
PCI card with 3 IP sites
PCI3IP
-
The PCI compatible PCI3IP design adds 3 Industrypack compatible slots to your PCI host. The PCI3IP acts as an adapter, converter, carrier, or bridge between the PCI bus and your IndustryPack hardware. The PCI3IP is a half size PCI card with 3 IP sites; compatible with the smallest chassis and the tallest processors that prevent full size solutions.
-
Product
Hand Held Video Tester
-
The hand held video tester is our world class video hardware and VIDSoft suite integrated to a micro PC via ATTI’s slot-0 service. The intent of the slot-0 service is to eliminate the bottleneck of VISA and PCI bridging.
-
Product
LCR Digital Bridge
FD2810B
-
• Test parameter: C, R, L, Z, D, Q• Test frequency: 100Hz, 120Hz, 1kHz, 10kHz• Test level range: 0.1V, 0.3V, 1.0V• Output impedance: 30Ω, 100Ω• Slow or fast (15 times/s)• Automatic selecting, out of limit alarming• Provide the RS-232 & HANDLER interface• Accuracy: 0.1%
-
Product
SCADACore Cloud-Connect
-
SCADACore’s Cloud-Connect products bridges your sensors and field operations to our fully-managed Web SCADA solution. SCADACore delivers complete end-to-end solution to bring field data to you anytime, anywhere.
-
Product
PXI-8360, MXI-Express Interface, PXI Remote Control Module
779501-01
Interface
MXI-Express Interface, PXI Remote Control Module—The PXI‑8360 allows you to control PXI and CompactPCI systems from your PC using a fully transparent MXI‑Express link. It is installed in a PXI chassis and uses a PCI Express‑to‑PCI bridge to interface with an installed PCI‑8360 through a copper, x1 MXI‑Express cable.
