Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
Plug-On Transmitter
HMa
-
This unique plug-on transmitter design will ideally match any microphone or line level source via a standard XLR connector. Phantom power is selectable at 5, 15 and 48 volts, or can be turned off for use with dynamic microphones and line level signal sources.
-
Product
Universal Test Fixture
Series 48
-
The Series 48 Universal Test Fixture Systems are an effective way to test high mix, low to medium volume products. The Universal Base is designed around the CAMGATE Z axis Test Fixture. The base interfaces with removable, quick change Series 49 Universal Test Insert Kits. Three versions are offered, a blank base whereas the end user can configure the Base and insert kit to their own connector configuration, The 160 point model which uses four (40) pin IDC ribbon cable connectors to interface between the base and the insert kit, and the -I model that incorporates the same 4 block GR2270 style block interface as used on our Series 34 test fixtures. This allows for increased test point count and the use of Industry Standard 2270 style signal, power, and coax blocks. Rear panels can be custom configured to customer specifications, Virginia Panel ITA frames, or GR2270 Interfaces used on Semco’s Standard Product line
-
Product
Cable Assembly, 160-Pin DIN41612, Female to Unterminated With Ferrules, 2m, 45º
A1604F5-F-0A200
Cable Assembly
For applications where a 45 degree cable exit would be preferred with unterminated connections at the other end. The cable assembly is constructed from highly flexible 7/0.15 (26AWG) Silver Plated Copper Wire. If the user requires the connector to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
Product
SP6T RF Pin Diode Switches To 12 GHz
-
The SP6T series of 6-way absorptive and reflective switches manufactured by Pulsar Microwave cover applications from 300 MHz to 12 GHz. They have an isolation of 60 decibels and most models specify 1.6:1 or better return loss throughout frequency band. These 6-way switches require a +/- 5VDC supply to operate. Switching control uses individual 0-5V TTL control logic. Voltage and logic control interfaces into a system using a 9-pin D-SUB connector installed.
-
Product
Dense Wavelength Division Multiplexer Mux & Demux Module 8 Channels 100G with LC/PC Connector
GLSUN-DWDM
-
Guilin GLsun Science and Tech Group Co., LTD
WavelengthITU channels 186.6 to 196.1 THzReturn Loss≥ 45 dBDirectivity≥ 50 dBConnectorLC/PCMax. Optical Power≤ 500 mWPDL≤ 0.15 dBRelative Humidity5%~ 95%Dimension100×80×10.5 mmOperating Temperature-10℃ to +70℃Storage Temperature-40℃ to +85℃
-
Product
32+2 Channel 12bit 5 GS/s Digitizer
VX1742
-
The Mod. VX1742 is a 1-unit wide VME64X board housing 32+2 Channel 12 bit 5 GS/s Switched Capacitor Digitizer sections. The input dynamic range is 1 Vpp on single-ended MCX coaxial connectors (16-bit DAC on each channel to control the DC Offset).
-
Product
25-Pin D-Type Male Right Angled PCB
40-963-025-RM
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 25-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Cable Assembly 78-Pin D-Type, Male to Unterminated With Cut Ends, 2m
A078HM5-C-0A200
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products.
-
Product
LXI Microwave Multiplexer, SP4T, 1-Bank, 50GHz, 50Ω, SMA-2.4
60-803-601
Multiplexer Module
Our 60-803-601 is a 1 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI High Voltage Programmable Resistor Module, D-Type Connector
40-230-041-HI
-
The 40-230-041-HI (PXI) and 42-230-041-HI (PXIe) are programmable resistor modules with 2 channels which can be set between 4Ω and 201kΩ with 0.25Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Chassis - Controls up to 16 8x1 Modules, 32 4x1 Modules or Mixtures or 8x1's, 4x1's, 2x1's and 2x2 Modules in Any Combination or Configuration up for up to 128 Relay Drives
CXM/128-MF
Chassis
These Chassis controls up to 16 8x1 modules, 32 4x1 modules or mixtures of 8x1"s, 4x1"s, 2x1"s and 2x2 modules in any combination or configuration for up to 128 relay drives. LEDs on the front panel show switch and power status. Add Switch Modules, display / driver modules and a Control Module to complete the system or simply buy the chassis wired out to D connectors to control your own relays. A manual control is optional. Chassis is available with sink or source relay drivers from + 5 to + 28 volts, ot TTL drivers for programmable attenuators. Firmware commands for Fade and Handover for WiFi, Cell Phone and WiMax labs. Fully custom systems built with little to no NRE.
-
Product
96 Pin 1.27mm Pitch Micro-D Cables - 96 Pin to 96 Pin for Pickering Products
-
The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a 96-pin micro-D connector.
-
Product
44-Pin D-Type Connector, Male, Right Angled PCB Mount
40-963-044-RM
-
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Pico-ITX SBC With Intel® Atom® X5-E3940 Processor, DisplayPort, LVDS, 2 GbE LAN And Audio
PICO319
-
The PICO319 is powered by the onboard Intel® Atom® x5-E3940 quad-core processor. The noise-free pico-ITX motherboard offers combinations of ruggedness, high computing capabilities and enhanced graphics capability in an extremely compact size of only 100 x 72 mm. Moreover, the board features 12V DC power supply input with AT Auto Power On function. A dual-display capability is available through DisplayPort and 18/24-bit single/dual channel LVDS ports. For extensive storage needs, this compact embedded motherboard has one M.2 Key B slot (22 x 42 mm or 30 x 42 mm) for SATA or PCIe x2 SSD card and one half-size PCI Express Mini Card slot in support of mSATA. The Intel® Atom®-based pico-ITX board comes with rich I/O connectors, including two USB 2.0 ports, two USB 3.0 (USB 3.1 Gen1) ports, one RS-232/422/485 port, one RS-232 port, one HD Codec audio, and 4-channel digital I/O. It also supports SMBus that is compatible with I2C for smart battery support. The PICO319 offers watchdog timer and hardware monitoring function for reliable operation.
-
Product
EN 50155 M12 8FE Managed Switch
EKI-9508E-MW
-
M12 connector with IP67 rugged housing, Complies with EN50155 & EN50121-3-2, Complies with EN45545-2 & EN61373, Wide nominal power input range: 24~110VDC; Operating power input range: 16.8~137.5VDC. Compact size to fit in different narrow spaces, Operating temperature: -40 ~ 70°C.
-
Product
68-Pin SCSI Micro-D Conn Block DIN
40-966-068-M
SCSI Male Connector Block
Suitable for mounting on DIN Rails this connector block provides a simple method of connecting to 68-Pin SCSI Style Micro D connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. The metal shell includes an internal insulation barrier under the carrier board.
-
Product
Eurocard Plugbord
4615
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors. 3-Hole Solder Pad Pattern on both sides. 3-Hole Solder Pads (0.28” x 0.080”) for interconnecting multiplecomponent leads.Interleaved buses on both sides, back-to-back. Pad and bus surfaces solder-coated for user convenience.Green Solder Mask both sides. Row and column legends provided.
-
Product
Cable Assembly, Receiver, 36", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
540112050240
Cable Assembly
Cable Assembly, Receiver, 36", QuadraPaddle to 2 x 78-Pin Female D-Sub Connectors
-
Product
Cable Assembly 15-Pin D-Type, Male to Unterminated With Ferrules, 0.5m
40-972-015-0.5m-MU
Cable Assembly
The 15 Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 21 AWG Tinned Copper Wire. The connector can be secured to the associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. When using this product additional cable strain relief arrangements may be necessary and appropriate electrical safety precautions should be observed.
-
Product
Pogo Connector P14028B180G120TL080ST
1024544
-
P14028B180G120TL080ST (item number 1024544) is a Pogo Connector for contact points that are connected and released frequently. As a spring-loaded detachable interface, P14028B180G120TL080ST is suited to repeated contact cycles such as charging and data contacts or other quick-release electrical connections. As a detachable spring-loaded interface, P14028B180G120TL080ST is suited to battery and charging contacts, mobile devices, measurement systems and industrial applications. The design combines a pitch of 2.2 mm / 87 mil with tip style 28 (4-point crown stepped) and a tip diameter of 1.8 mm. Spring force is 120 cN at a nominal travel of 1.2 mm. P14028B180G120TL080ST is specified for 8 A continuous current.
-
Product
Web Sensor
P8552
-
The devices are equipped with two connectors for connection of the temperature and humidity external probes and three binary inputs for two-states signals. The dry contact or two-state voltage signal can be connect to the binary input.
-
Product
20-Pin Scorpion Female Connector, 30A, Right Angle PCB Mount
C020AFX-2PR-3A
-
This is a female 20-pin Scorpion Connector, right angled, suitable for PCB mounting. The connector is keyed to position 2 and it has a maximum current handling of 30A and is suited for direct connection to Pickering Interfaces products.
-
Product
Waveguide To Coaxial Transitions
-
Waveguide to coaxial transitions are an integral capability of the business. TRAK offers a choice of connector type and orientation, pin/socket interfaces to waveguide apertures with a choice of standard or custom flange details.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-216-HI
-
The 40-230-216-HI (PXI) and 42-230-216-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 1.8kΩ with 8Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Basic Threaded Probe F73311B080G150
1001660
-
F73311B080G150 (item number 1001660) combines spring-loaded contacting with a secure threaded mounting concept. The threaded mounting of F73311B080G150 supports secure seating in wire-harness and connector tests, including setups exposed to vibration or lateral forces. The secure mechanical seat of F73311B080G150 is particularly useful in wire-harness and connector testing and in fixtures exposed to vibration or lateral forces. For installation, F73311B080G150 uses an M2 thread. On F73311B080G150, a pitch of 4 mm / 157 mil is combined with 150 cN spring force and 4 mm nominal travel. The electrical rating of F73311B080G150 combines 10 A continuous current with 25 mΩ typical contact resistance.
-
Product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Tinned Ends
A068SFR-T-5A050
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Female, 1m, Exit Away From Pin 1
40-970-050-1m-FF
Cable Assembly
The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products and is constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks.
-
Product
IBM PC-XT, Vectorbord Plugbord
4613-3
-
VECTOR Electronics and Technology, Inc.
62 contacts (31 each side) on 0.100" centers. Pad per hole. Voltage and ground buses around board perimeter. I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
MOD MONITOR
TYPE HFX-1
-
The Type HFX-1 Modulation Monitor is an ancillary piece of equipment, which is used with narrow bandwidth, or older oscilloscopes to allow viewing of RF signals and particularly modulated signals as high as 55MHz. The equipment contains an RF signal source and a broadband mixing circuit which converts the high frequency signal to an intermediate frequency within the oscilloscope’s range. The frequency control dial is simply adjusted until the RF signal is viewed on the scope. BNC connectors are mounted on the rear panel to allow interconnect to the scope and RF probe. This product was previously called "oscilloscope frequency extender" and may be used to view other high frequency signals on older or narrow band scopes.
-
Product
LXI 8:1 Optical MUX SC Loop-Thru
60-851-221
Multiplexer Module
The 60-850 and 60-851 are LXI conformant fiber optic multiplexers that use MEMS switching technology to ensure fast and reliable switching of single-mode (60-850) or multi-mode (60-851) optical signals being carried on fiber connections. The 60-850/851 is available with a variety of connector options and in a variety of multiplexer arrangements. Loop-thru versions are also available for easy multiplexer expansion.
