Connectors
dock multiple contact or data junctions.
See Also: Interconnects, Mass Interconnect, Cable Assemblies, Contacts, Harness, Wire, Test Point, Cable Assembly
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Ferrules
40-972-078-2m-FU
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-351-HI
Programmable Resistor Module
The 40-230-351-HI (PXI) and 42-230-351-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 2.95MΩ with 0.25Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
18" Cable
CONV1553-3
-
An 18" cable assembly transitions from individual IP Module ribbon connectors on: VME and VXI front panels (or internal VME-AIC connectors) to two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends.
-
Product
Cable Assembly, Receiver, TriPaddle, 36", 20-Pin Power Connector
540145010201
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 36", 20-Pin Power Connector
-
Product
Economy Mechanical Calibration Kit, DC To 6 GHz, Type-N, 50 Ohm
85032E
Mechanical Calibration Kit
The Keysight 85032E economy calibration kit contains a type-N male fixed termination and a one-piece type-N male open/short circuit. These standards are used to calibrate Keysight network analyzers for measurement of devices with 50 ohm type-N connectors. The kit is specified from dc to 6 GHz.
-
Product
8" Cables
RCONP1553-1
-
Transitions from each card end (non-IRIG) connector on various boards into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and two 8" cables with BNC cable jacks for I/O triggers.
-
Product
500-Pin SEARAY Cable Assembly, Male to Male, 1 Amp, 0.5m, 500 Port
A500RMR-500RMR-0A050
Cable Assembly
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.This cable assembly is for direct connection to products using the 500-Pin SEARAY connector (not compatible with Pickering products).
-
Product
Universal Multichannel System up to 100V
-
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 100 V output voltage- Maximum Current: 1mA, 10 mA or 1 mA/100 μA (dual range board)- Individual Enable (A1510 only)- Either DB37, DB25 or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA / 100 pA current set / monitor resolution- Up to 2 / 0.2 mV voltage set / monitor resolution- Extreme Low ripple, down to < 3 mVpp- 3 different channel grounding- Common Ground (AGxxxx)- Common Floating Return (Axxxx)- Full Floating (A1510 only)- Independently programmable for each channel:- Output voltage- Current limit- Ramp up/down- TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A1510)
-
Product
PXI High Voltage Programmable Resistor Module, REDEL Connector
40-230-353-HI
Programmable Resistor Module
The 40-230-353-HI (PXI) and 42-230-353-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 11.32MΩ with 1Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
Fiber Optic Power Meters
FOD1204H
-
The FOD 1204 & FOD 1204H Fiber Optic Power Meters are intended for accurate measurements of up-to-date optical communication. Very small temperature and temporal variations of Loss in Fibers and Connectors. Calibration of Optical Attenuators, Light Sources etc.
-
Product
CompactPCI Chassis
-
CompactPCI is a standard in computer bus technology for industrial computing that utilizes a Eurocard type connector combined with PCI signaling and protocols. cPCI boards come in 3U and 6U variants and are typically interconnected through a passive backplane. The connector pin assignments are standardized by PICMG , allowing for eight boards in a PCI segment with multiple bus segments being allowed with the use of active bridges.
-
Product
IndustryPack system trouble shooter
IP-DEBUG-IO II
-
IndustryPack system trouble shooter providing testpoints on all of the IP IO signals. Loop back is as easy as wire-wrap. Custom feedback signals are supported with socket and power connector support. Now with 2 ribbon cable connectors to support in system debugging.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 16-Bank 26.5GHz SMA
60-801-316
Microwave Multiplexer
The 60-801-316 is a 6-channel, 16-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
44-Pin D-Type Connector, Male
40-960-044-M
D-Sub Male Connector
This connector is designed to allow users to directly terminate cables with soldered connections.
-
Product
OEM Boards
4865B
-
* Embed the GPIB-to-Ethernet Interface in your instrument.* Available in three different connector configurations.* To have the GPIB Connector protruding thru the rear panel. Order P/N 115907* To mount the board anywhere inside the chassis and use an inexpensive flat-ribbon cable to a GPIB connector on the rear panel. Order P/N 115895. Order the 114439 Cable separately.* Mount inside the chassis and use a GPIB extension cable to a GPIB connector on the rear panel. Order P/N 115897.* Runs on instrument's DC power.* Same specifications and performance as the 4865B Minibox™ version.
-
Product
PXI/PXIe USB Data Comms Multiplexer, 16-Channel
42-737A-001
Multiplexer Module
The 40-737A-001 (PXI) and 42-737A-001 (PXIe) are 16:1 USB data communications multiplexers suitable for switching USB1 and USB2 data and power connections using a 78 way D-Type connector. The data signal paths are 2-pole arranged as differential pairs as defined by the USB standard.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 14-Bank 6GHz SMA
60-801-014
Microwave Multiplexer
The 60-801-014 is a 6-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 6GHz. It is part of a range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for between 1 and 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
FMC Add-On Cards
FPGA Board
iWave’s FPGA-IP Evaluation Add-On FMC Card is designed to meet ANSI/VITA 57.1 FMC Standard. The card supports both High-Pin Count (HPC) & Low-Pin Count (LPC) connector and can be used in an air-cooled environment. FPGA-IP Evaluation Add-On Card can be interfaced with most of the FPGA development kits available in the market. This card also helps to evaluate iWave’s proprietary FPGA Intellectual Property (IP) Cores.
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 50xDPST
40-146A-202
Relay
The 40-146A-202 (PXI) and 42-146A-202 (PXIe) 50xDPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
Two-Way Optical Loss Tester
KI23403OLV-INGAAS-APC-50U
-
A Two-Way Optical Loss Tester (OLTS) that's perfect for medium to ultra high fiber count loss, length and optical return loss testing applications on multimode fiber at 850 / 1330nm. A pair of these compact instruments set new standards of productivity, accuracy and ease of use. A multimode APC connector on this model is required for reliable ORL test performance.
-
Product
6TL08 Benchtop Test Platform
H710008
Test Platform
The 6TL-08 base platform was designed to cover the most common testing and in-system programming (ISP) needs with a reduced initial budget. The system includes a robust manual linear push mechanism allowing a low-cost fixture strategy thanks to the exchangeable cassettesThe platform enclosure features an 8-Slot fixture receiver, compatible with VPC 90 Series Mass Interconnect Module, as well as 6TL intelligent YAVModules (YAV90MMU &YAV90059), with room for fast ISP devices, optional PXI chassis and various power supplies. A removable back panel allows easy placement of custom connectors or test auxiliary circuitry.
-
Product
PXI/PXIe MEMS Optical MUX, 8-Channel, Multi-Mode, 50/125 Fiber, SC/PC Connectors
42-852A-218-M50
Multiplexer Module
The 40/42-852A-218-M50 is a PXI/PXIe 8-channel multiplexer with SC/PC connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications.
-
Product
Electrician & Technician Testers
-
EVSE's Electrician and Technician testers are created for installation professionals, and are small and durableenough to be carried in a toolbox. These weatherproof handheld units allow new chargers to be checked after installation, verifying a number of vital power and safety requirements, as they simulate the connection a charger makes with an electric vehicle. Simply plug the charger's J1772 connector into the tester's receptacle and you are ready to evaluate operation.
-
Product
200-Pin LFH PCI Connector Block, Male
50-965-200-M
Connector Block
Suitable for use on the front of PCI modules this connector block provides a simple method of connecting to high density 200-Pin LFH connectors. The screw terminals use a rising cage screw clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross sectional area and insulation properties.
-
Product
Mini Media Converter
MX Series
-
The MX mini media converter provides one RJ45 10/100/1000Base-T connector supporting auto-negotiation, MDI/MDI-X, full-duplex and half-duplex. The other connector is a 1Gbps SFP slot, suitable for any 1Gbps SFP module.
-
Product
Load Pull Test Fixtures
-
Low Insertion Loss for High VSWR TuningMultiple Connector Configurations50Ω and Transformers (Klopfenstein, Quarter-wave) AvailableHeatsinks and Fans AvailableCooling (Water cooling, Forced air cooling) AvailableIntegrated Biasing Available
-
Product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Ferrules, 0.5m, HV
40-972-037-0.5m-MU-HV
Cable Assembly
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
PXIe High Voltage Programmable Resistor Module, D-Type Connector
42-230-110-HI
Programmable Resistor Module
The 40-230-010-HI (PXI) and 42-230-010-HI (PXIe) are programmable resistor modules with 4 channels which can be set between 2.5Ω and 31.5Ω with 0.125Ω resolution with maximum voltage of 1kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
Product
SAEJ1962M-DE9M CAN OBD-II Cable, SAE J1962 to D-sub 9-pos F, 2m
193942-02
CAN Cable
9-Pin, Male SAE J1962 OBD-II Type A to 9-Pin, Female D-SUB - The OBDII9M-DB9F CAN Cable, sometimes referred to as the CAN OBD-II Cable, connects any NI high-speed CAN interface to an OBD-II compliant vehicle that has high-speed CAN on its diagnostic link connector in the passenger compartment. This high-quality injection-molded cable connects the CAN wires from the SAE J1962 connector to the standard CiA-DS-102 D-SUB connector wiring used by NI CAN interfaces. This cable is available with a high-speed CAN physical layer and no termination.
-
Product
3 Pin Power D-Type Cables - Connector To Unterminated For Pickering Products
-
The connector to unterminated cable assemblies below are suitable to use with Pickering cards and modules that utilize an 3-pin Power D-type connector.
