Drives
-
Product
Switch Drivers
-
Macom Technology Solutions Holdings Inc.
MACOM’s switch drivers bridge the gap between digital control signals and the analog voltages and currents required to drive our extensive family of RF, microwave and millimeter wave PIN diode and FET switches.
-
Product
Monitoring & Drive Test Antennas
-
Linear polarized half-wave dipole with 1:1 balun and fixed element length for fieldstrength measurements at TETRA (terrestrical trunked radio) networks.
-
Product
400 MHz High Voltage Differential Probe
DP0001A
-
The DP0001A is a 400 MHz high voltage differential probe with 2 kV mains isolated or 1 kV CAT III rating designed for making accurate high-voltage power measurements required for testing today’s WBG power devices, power converters or motor drives.
-
Product
Semiconductor Equipment Manufacturers
-
Integrated Dynamics Engineering
With shrinking process geometries, new structural elements and a major increase in substrate size, the challenges to improving process yield and overall throughput have increased exponentially. These demands drive a stringent requirement for system stability and overall immunity from internal and external forces.
-
Product
Dynamic Braking Resistors
-
Speed of three phase asynchronous squirrel-cage motors and three phase synchronous motors are generally controlled by motor drives where frequency of the drive output determines the motor speed, and it can be adjusted without dependence on the voltage magnitude.
-
Product
AC Reference Modules
-
NAI offers a variety of AC reference modules that provide a drive capability to 5 VA. The units are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. These modules are specifically designed for rugged defense, commercial aerospace, and industrial applications.
-
Product
Single Front Slot Universal Low-Profile PCI to PCMCIA Adapter, Black Bezel
P313B
-
To cater to the latest generation of low-profile PCs that can only use low-profile PCI add-in boards, Elan has created the P313. This model, from the P-series range, features a PCMCIA Type III 3.5" drive bay mounted slot and a circuit board that conforms to the MD1 profile specification. It will allow you to use any TypeI/II/III PCMCIA card.
-
Product
48-Ch Digital I/O And 3-Ch Counter PCI Card
PCI-1751
-
48 TTL digital I/O linesEmulates mode 0 of 8255 PPISupports both dry and wet contactInterrupt handling capabilityTimer/Counter interrupt capabilityBuffered circuits for higher driving capacity than the 8255Keeps the I/O port setting and DO state after system resetBoardID switch
-
Product
Isolation Amplifier Digital Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
Digital Brushless Servo Drives
DA Series
-
The DA series high performance digital servo drives integrates digital position and velocity control with built-in power supplies and the latest in PWM servo amplifier technology. Power range up to 50KVA.
-
Product
Desktop Appliance for PCI Express® Gen4
DE200-G4
-
A versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols, such as PCIe, SAS, and SATA.
-
Product
Programmable DC Power
TS Series
-
The TS Series utilizes the latest IGBT devices to drive down size and increase performance. The high frequency design delivers fast transient response and low output ripple. This performance coupled with Magna-Power''''s rugged current-fed power processing, enables confidence in even the most demanding applications.
-
Product
Pressure Sensors For Blast Testing
-
Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.
-
Product
96-Ch Digital I/O PCI Card
PCI-1753
-
Emulates mode 0 of 8255 PPIBuffered circuits for higher driving capacity than 8255Multiple-source interrupt handlingInterrupt output pin for simultaneously triggering external devices with the interruptOutput status read-back“Pattern match” and “Change of state” interrupt functions for critical I/O monitoringKeeps I/O setting and digital output values when hot system resetSupports dry contact and wet contactHigh-density 100-pin SCSI connector
-
Product
3U CompactPCI Serial Front Removable SATA Carrier for SSDs
SD8-STEEL
-
The SD8-STEEL is a peripheral slot card for CompactPCI® Serial systems. It includes a shuttle for 1.8 or 2.5” SSD or HDD drives. Signal integrity is optimized with 6Gbps SATA drivers. A push button ejection of the drive enables easy swap removal.
-
Product
System
SYS-24
-
The system shown here was built for a customer to be used in metallization, a common use for many smaller systems. It is also fully capable of performing optical coatings when equipped to do so. This particular system came equipped with a 16" APD ISO Flange mounted cyropump, and a Varian tri-scroll for roughing. The cooling tubes for the crystals as well as the drive motor for the parts holder can be seen on the top of the chamber.
-
Product
Talon RTX Small Form Factor Offload System
Talon RTS 2580
-
- The Talon® QuickPac® drive can be removed from a Talon RTX - SFF recorder and inserted in this offload system- Allows the Talon recorder to remain deployed in the field- Data stored on the QuickPac drive can be accessed and offloaded for analysis- Designed for Talon models RTX 2586, 2589, 2590, 2596, and 2684- Can offload data to removable SATA drives, DVD, Ethernet and USB ports- 4U 17-inch PC server chassis, 21 inches deep- Windows® workstation- Intel® processor- 8 GB DDR SDRAMSystemFlow® Software
-
Product
PXI 32 Channel I/O, Low Side Driver
40-413-002
-
A 32 channel Digital I/O module with high output voltage and current capability and a dual variable threshold input. The 40-413 range is available in three configurations, a high side only, a low side only (shown here)and a combined high and low side each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments. For high side voltage driving the high side voltage source is supplied from an external voltage source, permitting the module to drive high capacity loads without impacting the PXI chassis power supply.
-
Product
CAT-5 Video Variable Filters
-
It is often beneficial to use a video driver at the output of a video encoder for power savings, line driving, and additional circuit protection. The video driver is typically configured as an active filter, also known as a reconstruction or anti-imaging filter. The purpose of the reconstruction filter is twofold: it blocks the higher frequency components (above the Nyquist frequency) that were introduced into the video signal as part of the digitization process and provides gain to drive the external 75 Ω cable to the video display.
-
Product
Frequency Synthesiser
RA062-F2
-
The RA062-F2 is a multiple LO module used to generate three pairs of LO signals, each pair being phase matched in order to provide the capability to drive two phase and amplitude matched, high sensitivity narrowband receivers such as might be required for an EW receiver system with DF functionality.The Stepped Frequency Synthesiser is based upon Direct Frequency Synthesis, DFS, whereby the 1GHz input reference signal is multiplied, filtered and mixed to generate a given number of isolated and filtered single tone CW signals from the 1GHz comb. A finely tuned signal is then generated using a multi-way switch to select between the 1GHz spaced CW tones and mixed with fine resolution signals generated using a custom DDS/VCO PLL network. In this way finely tuned signals can be generated between 7.5GHz and 23GHz.
-
Product
Electric Servo Motor Type 2 Axis Switching Simultaneous Vibration Tester
-
It is a 2-axis switching vibration tester and a 2-axis simultaneous vibration tester that mounts an electric servomotor actuator on the vibration drive unit.
-
Product
RGB 1×3 Video Distribution Amplifier
VDA403
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.The second application is when the video signal is run over distances greater than 50 feet. The coaxial cable has a fair amount of signal loss over long distances. When multiple monitors are connected after long runs of coax, the degradation can be severe, especially when dealing with modern, high bandwidth signals that have 500+ lines of resolution.The VDA403 is a Video Distribution Amplifier designed for professional applications. It will operate with NTSC & PAL video signals as well as many common Black & White signals. These units use the latest integrated amplifier technology for superior performance and reliability. Custom units or modifications can be manufactured at a reasonable cost.
-
Product
Thyratrons and Accessories
-
Cargo scanning is a broad term which encompasses intelligent logistics, sniffer dogs and X-ray inspection. X-ray inspection systems offer rapid, non-invasive checking of manifests, detection of contraband, and when combined with other techniques, can be used to identify the presence of nuclear material. X-ray energies up to 10 MeV are required to penetrate fully loaded shipping containers and vehicles. These X-rays are generated through the acceleration of electrons along a linear accelerator into a target using megawatt energy microwave pulses produced by the RF sub-system.The skills for the design, manufacture and integration of specialised components for low-cost systems reside mainly in commercial companies. There is an emerging trend for linac system companies to demand higher performance from their integrated RF sub-systems.Currently, we intend not only to drive the innovation and development in this area, but also to offer integrated RF sub-systems to meet new requirements such as, portability, material discrimination and higher throughput.
-
Product
Hydrophone
TC 4037
-
Incorporating a 10dB low-noise preamplifier able to drive a 25-metre cable and a wide usable frequency range, the TC 4037 is a spherical probe hydrophone that’s ideal for measuring sounds in the 100 to 500kHz range.
-
Product
CalPod Drive Cable Extension, 10 Meter
85554A
-
85554A CalPod Drive Cable (10 meter length) extends the length of CalPod control cables when the distance between the 85523B to the CalPod modules is >2 m.
-
Product
On-board Emissions Measurement System
OBS-ONE PN Unit
-
The OBS-ONE PN unit is an on-board emissions measurement system for analyzing the solid particle number concentration within the specified particle size range under real-world driving conditions. The unit uses a condensation particle counter which is recommended principle by the Particle Measurement Programme (PMP), one of working groups affiliated with UNECE.The PN unit combines with the GAS unit to measure the specified exhaust gas components, along with the exhaust gas flow rate, the GPS position, and the atmospheric conditions (temperature, humidity, pressure).
-
Product
Flexible Pick And Place Machine With 128-feeder Capacity
MC385V1V
-
The high-precision MC385V1V Pick and Place system ensures accuracy and repeatablity with high-quality ballscrew drive, linear encoders, and full vision alignment. Programming and operation are made easy with mature, fully supported Windows-based software. Machine holds up to four 32-port feeder racks for a maximum feeder capacity of 128 tapes. Waffle trays and cut strip tape holders can be used in the placement area.
-
Product
2-CH Pulse-Train Motion Control EtherCAT Module
EPS-7002
-
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
-
Product
3U cPCI Synchro/Resolver Simulation Board
75DS2
-
NAI’s 75DS2 is a Synchro/Resolver Simulation Board with four independent, isolated channels. These channels can incorporate up to four Digital-to-Synchro/Resolver Simulation Converters with 1.5, 2.2, or 3 VA drive capability, or either two or four Digital-to-LVDT/RVDT Simulation Converters. One of the outputs on each channel can be grounded without affecting performance.
-
Product
Embedded ROS 2 Robotic Controller Powered By NVIDIA® Jetson AGX Orin ™ Module
RQX-59 Series
-
Introducing the revolutionary ROScube-X RQX-59 Series, a state-of-the-art ROS 2 robotic controller powered by the incomparable NVIDIA® Jetson AGX Orin™ module. The RQX-59 Series ensures seamless integration into robotic and autonomous driving applications, thanks to its integrated powerhouse NVIDIA CUDA® GPU and dual deep learning accelerators. Additionally, it offers a wide range of interfaces, including GMSL1/2 or FPD-Link III cameras. Get ready to redefine the boundaries of robotic possibilities with the RQX-59 Series, the epitome of efficiency and innovation.
