Conducted Immunity
EUT's resilience to an injected disturbance through associated cable.
See Also: Immunity Test, Coupling Decoupling Network
-
Product
EMC Testing Services
-
Our sophisticated technology can meet the diversified needs of customers. Component Tests: Immunity, Radiated Immunity, ALSE, TEM cell, Bulk Current Injection, Stripline, Conducted Immunity, Transient Immunity, Power Supply Variations, Electrostatic Discharge Emissions, Radiated Emissions, Conducted Emissions, Transient Emissions. Vehicle Tests - Radiated Immunity, Radiated Emissions.
-
Product
Coupling Decoupling Network (CDNE)CDN
Emissions
-
CDNEs are based on the CDN as specified in IEC61000-4-6 (Conducted RF Immunity test). In this test, the CDN is used for the coupling of RF onto a cable. In principle, the CDN can be used in reverse, ie coupling any RF on the cable out to an analyser. In an earlier version of EN 55015, these CDNs were specified as suitable for measuring emissions. However, the current version of the standard specifies a CDNE which is essentially a CDN refined to deliver higher accuracy particularly at higher frequencies.
-
Product
Conducted Immunity Test System
-
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
EMC Testing Knowledge & Equipment
-
Creating, delivering, installing, and training on EMC test systems; RF Immunity systems, RF Radiated and Conducted Emissions systems, Conducted Immunity and Pre-compliant EMC systems.
-
Product
Conducted Immunity Test Systems
-
Conducted Immunity System (CIS) to Test According to IEC 61000-4-6. The CIS series test systems are configured to perform conducted immunity testing according to IEC 61000-4-6. The system includes an ACS series power amplifier, coupling/decoupling Network (CDN), directional coupler, 150Ω to 50Ω adapters, power attenuators, cables and [optional] CSAT software. These systems, when properly configured, are capable of testing your products to all levels given in IEC 61000-4-6 up to 230 MHz. You can choose from three systems. Follow the links below for detailed information, including a comprehensive datasheet listing system specs.
-
Product
Immunity
RF coupling
-
is used for the conducted measurement of the immunity according to IEC 62132-4.
-
Product
Electromagnetic Immunity Scanner
SmartScan BASIC
-
The BASIC is manually operated system for performing susceptibility scanning at the system level with minimal data storage capability. This system includes:1. Up to 8kV (optional. 4kV base) pulse generator for ESD susceptibility testing- Camera and camera shutter to take DUT picture and failing spots- Control computer2. Up to 8kV Probe Sets:- 1mm Hx/y Field Probe- 5mm Hx/y Field Probe- D=8mm Hz Field Probe- D=8mm Ez Field Probe- Contact API for custom design probes3. Manual input of testing location and failing condition over the DUT to be included in final report.
-
Product
Conductivity Meters
-
There are both standard and a waterproof conductivity meter, as well as a conductivity meter available for flowing water or pure water (highly recommended for specific industries) as well as the ones with different conductivity measurement ranges. An important factor is that a conductivity meter normally measures electric conductivity in µS/cm, however it can also take measurements in mg/l (for direct reading of content in dissolved solid substances). The relation is established as follows: 2 µS/cm = 1ppm (parts per million) = 1 mg/l. Compensated temperature in the conductivity meter can be automatic or by hand.
-
-
Product
Immunity Development System
-
Used for EMI suppression in printed circuit boards during the development phase. The developer can use the E1 set to quickly identify the causes of burst and ESD interference. This allows the developer to design suitable measures to solve the causes of the interference. It can also be used to test the effectiveness of the measures taken.
-
Product
Conductivity Logger Sensor
NUL-215
-
This logger sensor is based on a probe with two electrodes with known surface area and distance between them. A signal is supplied to the electrodes and by testing the signal behavior, the conductivity of the solution is calculated
-
Product
Non-aqueous Conductivity Probe
DT-700
-
From pure toluene to distilled water in one instrument.Quality control of non-polar liquids, ionic and surfactant composition.
-
Product
Conductivity Sensor
ACF60-35
-
Knowing the conductivity of liquid samples is a key parameter to control product quality throughout the production process. The optek ACF60 conductivity sensor fulfils technical requirements of international regulations for reliable measurements ensuring quality and consistency.
-
-
Product
Electrical Conductivity Measuring Instrument
SIGMASCOPE® SMP350
-
Compact handheld device for measuring the electrical conductivity of non-ferrous metals.
-
Product
Online Conductivity Controller
LD-LOCC-A10
-
Online Conductivity ControllerLD-LOCC-A10features 3 points conductivity calibration system, TDS measurement mode, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, Temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. This controller measures Conductivity and TDS values in µS/ cm, and mS/ cm units.
-
Product
EFT Immunity Measurement
EFT61000-4
-
EFT immunity tester EFT61000-4 is specially designed according to the characteristics and requirements of EFT measurement and it is an ideal disturbance source of EMS measurement. They have fine performance, such as high stability, high reliability, easy to use etc. It meets the standard requirements of IEC 61000-4-4, EN 61000-4-4, GB/T17215.301, GB/T17215.322 and GB/T17626.4. EFT61000-4 has LCD display in both English and Chinese.
-
Product
Digital Conductivity Pen (EC)
CD611
-
The Milwaukee Conductivity Pen is designed for hydroponic and other growers to help you make sure that your plants are receiving the right amount of nutrient. Keep EC in your target range to help your achieve better results.
-
Product
Benchtop Conductivity Meter
LAQUA EC2000
-
Water quality analysis is repeatedly performed in laboratories on a daily basis. Our compact and powerful benchtop model was developed to provide simplicity with excellent on-site usability.
-
Product
Conductivity/ Temp/ Depth (CTD)
-
Durable, waterproof data loggers designed for monitoring water quality, salinity, and water levels in fresh or saltwater environments.
-
Product
Digital Conductivity Pen (EC)
CD601
-
The Milwaukee CD601 digital electrical conductivity (EC) Pen is designed for aquariums, aquaculture, pools, water conditioning and many other applications. The CD601 helps you make sure that your water has the right amount of nutrient to help keep fish tanks healthy or helps you keep your filters up-to-date and clean for water filtration. Keep EC in your target range to help your achieve better results.
-
Product
NON CONDUCT DIGITAL THERMOMETER
IBL-MT9
-
International Biological Laboratories
This Digital Non Contact type Infra Red Thermometer with laser sensor uses temperature sensor of Thermopile 8 - 14 mm and measures temperature from -50 to 1000 Degree C and also in Fahrenheit scale.
-
Product
Electromagnetic Immunity Scanner
SmartScan 350
-
Reproducing similar soft or hard failure to the gun test - Flexible automatic failure detection module - Susceptibility map generation- Automatic report generation- Flexible scan area editor (SAE)- Flexible display (3D, histogram)- Matlab support- Expandability (EMI scan, phase measurement, NFFF transformation)- Custom design probes
-
Product
Conductivity Sensors
-
Conductivity sensors measure the specific conductance of liquid processes. The specific conductance is directly related to the presence of ionic species and their concentration. Barben Analytical offers a full range of two electrode and four electrode contacting conductivity sensors for a variety of industrial measurement applications.
-
Product
RF swept immunity package
EMiSweep
-
This is a flexible Windows immunity package which provides the utilmate flexible Graphical User interface. Other visual aids provides a swept as well as spot frequency assessment.
-
Product
Conductive Anodic Filament Testing
AutoCAF2™
-
AutoCAF™ is able to measure up to 256 individual measurement sites under conditions of high humidity and temperature in accordance with IPC-TM-650 2.6.25 Test Method & IPC 9691 CAF Test Users Guide.
-
Product
Thermal Conductivity Gas Analyzer
CI2000-RQD
-
Shanghai ChangAi Electronic Science & Technology Co.,Ltd
Determining gas concentrations by measuring the thermal conductivity of the gas, CI2000-RQD analyzer uses advanced thermal conductivity sensor with single chip technology. It adopts platinum thread as sense organ to make up Imbalance Bridge, which output signal has a relationship with tested gas volume. And the single chip will magnify, sieve wavelength, modify linearly and criteria the signal by electric procedure.
-
Product
Shielding Effectiveness/ Conductivity Test
EM-2107A | 30 MHz – 1.5 GHz
-
The EM-2107A is a standard test fixture for evaluation of the electromagnetic shielding effectiveness of planar material. The fixture is an enlarged section of coaxial transmission line and complies fully with the requirements of ASTM test method D4935-1. The measured data relates to the shielding effectiveness due to a plane wave (far field EM wave) from which near field values for magnetic and electric fields may be inferred. The EM-2107A is provided with a reference standard test specimen, a dynamic range specimen. Dynamic range of greater than 80dB is achievable, although the cables and other test system components usually establishes the limiting factors.
-
Product
Conductive Polymer Hybrid Aluminum Electrolytic Capacitors
-
Panasonic Industrial Devices Sales Company of America
Panasonic’s Hybrid Capacitors combine the benefits of Aluminum Electrolytic and Specialty Polymer Capacitors resulting in a Capacitor featuring high endurance, low-ESR, high tolerance for ripple current, inrush currents and elevated temperature. Hybrid Capacitors are known for their stable electric characteristics at high frequencies while maximizing reliability. These Hybrid Capacitors are compact, allowing significant board space savings and vibration-proof parts are also available.
