Down Converters
Change a higher frequency signal to a lower frequency.
-
Product
RF Telemetry Receivers, Tracking Receivers, Down Converters
-
Lumistar offers single PCI slot multi-band FM receivers. The same product in a “drive Bay” configuration is available. All Lumistar FM receivers can come without the FM demodulator use as antenna tracking receivers or for use as down converters used with an IF receiver for multi-mode digital combining and demodulation. Dual channel versions are also available.
-
Product
Noise Sources
WGNS
-
The system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device operating in the 26.5 – 170GHz range on wafer as well as in benchtop applications. Farran offers the WGNS series of noise sources to be used in conjunction with the FBC down converters for use as frequency extenders for noise figure measurement test system.
-
Product
Frequency Converters
-
Ducommun's frequency converter families include waveguide detectors (FAS), passive and active multipliers (FMP and FMA), up and down converters (FUB and FDB), harmonic mixers (FDH), subharmonically pumped up and down converters (FUS and FDS) and phase detectors and single sideband modulators (FPB and FSS). These devices are offered in 7 waveguide bands to cover entire 18 to 110 GHz frequency spectrum. These converters employ high performance GaAs Schottky beamlead diodes and DLT's proprietary circuit configuration to produce superior performance, such as low conversion loss and up to full waveguide instantaneous operation bandwidth.
-
Product
Es'hail-2
-
The geostationary amateur radio satellite Es'Hail-2 is in the air. Our development team worked on a great all-in-one solution to use the satellite from Qatar as a radio amateur. The result was the standalone up converter for the OSCAR PHASE 4 and a low noise down converter. The products were shown for the first time in 2017 and 2018 at Ham Radio in Friedrichshafen. Even then, the interest of our amateur radio customers was great. On 15.11.2018 it was finally time! The rocket that launched the satellite into space began punctually at 21:45 in Florida with numerous spectators on site and in a live stream. Start connecting with our products and the Es'Hail-2 satellite.
-
Product
PXIe Down Converter: 4 Channels, 2-16 GHz RF, 0.01-2.4 GHz IF
M5201A
Downconverter
Single-slot PXIe low-IF downconverter module with a 2 to 16 GHz RF input frequency range and 0.01 to 2.4 GHz IF range
-
Product
Aluminum Portable Telemetry System with Integrated Keyboard and Display
LS-84-AP
-
The Lumistar LS-84-AP Rugged Aluminum Portable Data Unit offers a low cost, high performance COTS solution for aportable quick look ground station. Lumistar LS-25 FMReceivers or LS-25-D2 Down Converters with LS-35-R Multimode IF Receiver, Bit Synchronizers and Multi-function PCM Decommutators, and LS-71D/A Converters can be installed inthis rugged high quality portable computer and bundled with theLumistar setup, control, and monitoring software to achieve anaffordable alternative to the often expensive, proprietary architecture products of other suppliers. The flexible design allows the user to define the desired data acquisition cardconfiguration to unique requirements.
-
Product
High Performance 335 M, 6 Channel Digital Receiver
DP-VME-5838
-
The DP- VME-5838 is a VME64x slave, high performance 335M, six channel Digital receiver card. It samples and down converts the analog IF signals into the digital base band data. The processed I/Q data are pulse compressed and decimated to the base band rate. In the Central Unit system, this pulse compressed I/Q data has to be sent to the signal processing unit through a 2.5G speed Optical SFPDP link.
-
Product
Scalers & Converters
-
Down convert VGA, HD-SDI, HDMI, and DVI computer video signals to a composite video signal Industry-leading multi-resolution and multi-format signal conversion and scaling products for Pro AV systems.
-
Product
Generic RF ATE Test
-
The Generic RF ATE is developed to test the Radar and Radar Subsystems. The ATE is primarily built using an instrumentation control, precision RF routing systems and rack mounted test instruments. Generic RF ATE system enables measurement of parameters of Radar equipment such as Local Oscillators, Waveform Generators, Up and Down Converters, Analog Receivers, Array Group Receiver Units, TR Modules. The ATE is configured to test the Radars upto 18GHz frequency range.
-
Product
Up/Down Converters
-
Over the years, In-Phase Technologies has received many requests for frequency conversion units. Our standard product line of frequency converters includes models that operate from RF though 60 GHz. Many options are available to complement our standard offerings. We also have a series of RF-to-optical converters that allows customers to send RF and microwave signals over fiber optic cables.
-
Product
PCI Dual Channel Multi-Band Down Converter
LS-27-D
-
The Lumistar LS-27-D3 TwoChannel Quad Band PCI Down Converter product is a 3rd generation high-density, high performance down converter designed using the sameadvanced technology as in the industry leading LS-25 PCIReceiver. The down-converter converts one or two independent channels of up to four RF frequency bands down to a 70 MHz IF output. The LS-27-D3 is typically used in conjunction with theLumistar LS-35 Series Digital IF Receiver/Combiner to provide one or two independent telemetry receivers, or a dual diversity combining receiver, with up to two multi-mode demodulators and bit synchronizers in a two-slot PCI interface. The number of channels and frequency band designations can be specified at the time of order. Please see the data sheet for the LS-35-R Digital IF Receiver/Combiner for more information.
-
Product
Wideband Digital Down Converter
-
A Digital Down Converter performs channel access functions in digital receivers. It is used for extracting a channel (frequency band) of interest in a wideband signal. Abaco Systems' wideband DDC core employs a quad DDC architecture to achieve ultra high performances. The core accepts up to 16-bit complex data and can process 1GSPS continuously. With a fully programmable architecture at all stages of the processing, this core combines flexibility and speed and can be used in combination with our dual-channel 1GSPS ADC module.
-
Product
6 Channel Digital Receiver Module
DP-VME-5826
-
DP-VME-5826 is a VME64x Six Channel Digital IF Receiver module. It samples and down converts analog IF signals into the digital base band data.The digital base band I/O samples generated from these IF samples are pulse compressed. Down converted I/Q data is sent to the signal processor through 2 channels of 2.5 Gbps speed SFPDP link.The digital waveform generator block of digital receiver unit generates programmable polyphase coded digital pulse coded expander output.
-
Product
64 Channel Dual IF Signal Processor
DP-VME-5247
-
DP-VME-5247 is a VME64x Dual IF Signal Processor . This dual channel up converter and down converter on-board real time data processing and analog output. This board is particularly suited for radar systems where the signals must be sampled at high rates and very high purity programmable signal generation. Application range encompasses IF signal processing, radar systems, communication systems, and IF data logging systems.
-
Product
RF & Microwave
-
Data Patterns has a strong RF and Microwave engineering capability, featuring a team of enthusiastic engineering talent, substantial investments in RF test and measuring instruments, and attitude to utilise the latest technologies.An in-house manufacturing capability and an insatiable demand for fulfilling requirements of Radar, Electronic Warfare and Communication domains, Data Patterns has developed a whole line of building blocks including TR Modules, Up and Down Converters, Power Amplifiers, Transmitters, Combiners and Dividers for specific requirements. A list of products is given below.
-
Product
8-Channel 250 MHz A/D Jade XMC Module w/ 72 DDCs for Defense & Radar Phased-Array Applications
-
member of the Jade" family of high-performance data converter XMC modules based on the Xilinx Kintex Ultrascale FPGA. The Model 71132 is an XMC module featuring eight 250 MHz 16-bit A/Ds with eight wideband digital down converters (DDCs) and 64 multiband DDCs, all fully programmable. The Model 71132 doubles the number of A/D channels and DDCs over previous models giving this the best price per channel ratio in the product family. Applications monitoring a broad spectrum with a need to quickly analyze specific portions of the identified spectrum can greatly benefit from the capabilities of the 71132.
-
Product
PCI Single Channel Multi-Band Down Converter (ISA and VME Legacy Versions Available)
LS-25-D
-
Lumistar offers single PCI slot multi-band FM receivers. The same product in a “drive Bay” configuration is available. All Lumistar FM receivers can come without the FM demodulator use as antenna tracking receivers or for use as down converters used with an IF receiver for multi-mode digital combining and demodulation. Dual channel versions are also available.
-
Product
Remote Spectrum Analyzers
LPT-3000RX4
-
Latest DSP Technology; 9 kHz to 3 GHz Frequency Range; External 10 MHz Reference; 17 RBW filters Down to 1 Hz; 17 VBW filters Down to 1 Hz; > 88 dBm Dynamic Range; High Definition Spectrum Trace; 55 dBm Input Port Isolation; 50 dBm input attenuator; 0.5 millisecond Port Switch Speed; Available in 4, 8 or 16 RF inputs; Optional Internal Carrier Identification CID module; Optional Internal Down Converter modules
-
Product
Block Downconverter
RQ028
-
Teledyne Defence & Space (TDS) down converters are designed to convert digitised, band limited RF signal down to a lower frequency signal. These modules are used to reduce input signal which allows lower speed processors to better process fast incoming signals. A wideband mmW block downconverter suitable for extending the operational bandwidth of other devices into this range. With LO signals at 32GHz and 44GHz, two operational bands are available. Other frequency plans with and without pre-selection can be offered on request.
-
Product
500-Watt (270VDC Input) DC/DC Converter, 3U VPX
VPX57-31
DC Converter
NAI’s VPX57-31 is the industry's first 500-Watt DC/DC Converter that accepts a +270 VDC Input and plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
725-Watt (28VDC input) DC/DC Converter, SOSA™ Aligned, 3U VPX
VPX55HS
DC Converter
NAI’s VPX55HS-31 is NAI's latest +28 VDC Input, VPX DC/DC Converter. The VPX55HS was developed in alignment of the SOSA™ Technical Standard and is capable of handling up to 725 Watts of output power. It plugs directly into a standard 3U VPX chassis with a VITA 62 1.0” power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
400 Watt DC/DC Converter, 3U VPX, Holdup Time
VPX68
DC Converter
NAI's VPX68 is a rugged and high-efficiency 400-Watt Output +28 VDC Input 3U VPX DC/DC converter designed for aerospace, defense, and industrial markets. It is an off-the-shelf power supply with optional integrated Holdup Time that plugs directly into a standard VITA 62 conduction cooled chassis. The power supply, engineered to meet harsh environmental conditions, includes continuous Background Built-In-Test (BIT), I2C communication, remote error sensing, and protection against Input transients, over-voltage, over-current, and short-circuits, ensuring reliable and consistent performance.
-
Product
400-Watt DC/DC Converter
VPX55-3
DC Converter
NAI's VPX55-3 is 400-Watt DC/DC Converter that plugs directly into a standard 3U VPX chassis with a VITA 62 0.8" power supply slot. This off-the-shelf solution for VITA 46.0 and VITA 65 systems is compatible with VPX specifications; supports all VITA standard I/O, signals, and features; and conforms to the VITA 62 mechanical and electrical requirements for modular power supplies.
-
Product
AC-DC Rectifier / Converters
DC Converter
These following AC-DC converters all can provide 3.3/5/9/12/25/24/28/48V etc output. Newly acquired 2U rack mount 48V rectifier is a mature solution for 48V telecom systems.
-
Product
Digital to Synchro Converters
DSP
Digital / Synchro Converter
Computer Conversions Corporation
The DSP Series are high efficiency, AC Reference powered, Transformer Isolated, continuously updating “whole” Digital to Synchro Converters, designed for high performance Military and Industrial applications.
-
Product
PXI/PXIe Digital To Analog Module - 4 Channel
43-770-001
Digital / Analog Converter
The 41-770-001 (PXI) and 43-770-001 (PXIe) have four Digital to Analogue Conversion channels in a single PXI/PXIe slot. Each channel is fully isolated and able to supply a programmable voltage or programmable current output. The outputs can work in one of several modes of operation: ±1 V, ±2 V, ±5 V, ±10 V, ±20 V, 0-40 V, ±5 mA, ±10 mA, ±20 mA. Each channel of the 41/43-770 module is able to simulate the open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
PXI/PXIe Digital To Analog Module - 4 Channel
41-770-001
Digital / Analog Converter
The 41-770-001 (PXI) and 43-770-001 (PXIe) have four Digital to Analogue Conversion channels in a single PXI/PXIe slot. Each channel is fully isolated and able to supply a programmable voltage or programmable current output.The outputs can work in one of several modes of operation: ±1 V, ±2 V, ±5 V, ±10 V, ±20 V, 0-40 V, ±5 mA, ±10 mA, ±20 mA. Each channel of the 41/43-770 module is able to simulate the open circuit conditions that can be experienced in a system due to faulty wiring or sensors.
-
Product
Analog-to-Digital Converter Board
VME-3125A
Converter Board
Isolated Scanning 12-bit 32-Channel Analog-to-Digital Converter Board (6U) with Built-in-Test (BIT)
-
Product
Synchro to Digital-Resolver to Digital Converters
Synchro- Burst
Digital / Synchro Converter
Computer Conversions Corporation
Computer Conversions Corporation's Synchro-Burst is a complete 2 channel Synchro to encoder interface designed to easily integrate inherently absolute rotary synchro, resolver or linear LVDT position sensors into motion controls and counters that are normally only designed to facilitate incremental encoder feedback.
-
Product
8 channel 16 bit Digital to Analog Module
CPCI-DA8-2
Digital / Analog Converter
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system.
