Down Converters
Change a higher frequency signal to a lower frequency.
-
Product
Press Down Rods Bed of Nails Testers
RandHDPE HDPE Family
-
HDPE plastic plates for extra easy machine ability and upgradeability. Designed for Research & Development and Pre-Production where product engineering changes are a weekly issue. The primary design focus is easy upgradeability. In R&D and Preproduction, design changes can happen every week. This fixture unlike normal test fixtures was designed to be easily taken apart and updated. Disassembling a normal bed of nails test fixture over and over again can be a major disaster with wire breakage and test pin bending issues. The modular design of the Rand fixture allows for easy disassembly without flexing the wires or risk of bending test pins. The Rand fixture provides complete easy access for machining, drilling and wiring updates.
-
Product
DC/DC Converter 2 W
REM2-153.3D
-
DC/DC converter 2 W from Recom | input ranges 13.5 - 16.5 VDC | outputs +/-3.3 V | operates in ambient temperature from -40 to +95 °C
-
Product
USB to RS-422/RS-485 Converter
ND-6530
Data Acquisition Module
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
Product
Meat Cooking and Cool Down Temperature Data Logger
OT1000
-
The OT1000 is made of Tecaform®, with a convenient mounting hook. The device is rated IP67, making it splash proof and easy to clean. The OT1000 is simple to use, just activate the logger, insert the probe into a meat product, and then with a couple clicks of the mouse data can be downloaded to a PC for analysis.
-
Product
ANSI X3.28 to Modbus RTU Converter
Model 2399
-
* Converts ANSI X3.28 commandslinto Modbus RTU packets.* New 32 Address Mode supports multi-channel Modbus Controllers like the Watlow MLS300.* Control Modbus RTU devices from any ASCII serial source.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes serial baud rate conversion.* Internal logic is IEEE-488.2 compatible and uses SCPI commands for configurtion setup.* 2399 mounts on a DIN rail or on any flat panel.* Inexpensive way to maintain manufacturing equipment such as semiconductor fusion chambers, etc as the ANSI Controllers become obsolete.* Application Note AB23-3 describes how to use the 2399 to replace obsolete Watlow Controllers in the Axcelis/Fusion Gemini Asher.* 2399 Serial Keyboard Program lets you control and setup the 2399 and test the ANSI modes.* 239x Table Loader Program uploads ANSI Command Table entries from an Excel csv file.
-
Product
Standalone IP To ASI Converter
DTE-3100
-
DekTec's standalone power-over-ethernet enabled IP to ASI Converter, allowing zero-jitter transmission of Transport Streams coming from IP networks.
-
Product
Signal Spectrum Converters
-
Advanced Science and Novel Technology, Co., Inc.
DC to 5.6GHz finite impulse response filter.Two differential CML-type input ports and one differential CML-type output port.Nine analog tap-weight control inputs.Differential gain of approximately 0dB.Single +3.3V or -3.3V power supply.Power consumption: 422mW.Fabricated in SiGe for high performance, yield, and reliability.Custom CQFP 44-pin package.
-
Product
Standalone Media Converters
-
Advantech's standalone media converter facilitates cabling with simple conversion and optional internal power security device.
-
Product
Interface Converter
ZET 7176
-
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
Product
- RS-232 to RS-422 Interface Converter
Model 263
-
No AC or DC Power; Full Duplex RJ-11 and Screws; Surge Protection. The Model 263 power stealing RS-232 to RS-422 interface converter offers the user the benefits of other Telebyte converters without the problem of supplying power. With only TD, RD and Ground the Model 263 will provide operation over 8,000 feet of twisted pair into a load of 120 Ohms.
-
Product
LVDS To DVI-D Converter Board
AX93221
-
*Input supports 18/36/24/48-bit LVDS through 40-pin LVDS connector*Output supports DVI-D connector*Size: 60 x 50 mm*Applied for PICO821 and PICO822
-
Product
Single-Supply Voltage Output D/A Converters
-
Analog Devices offers the broadest portfolio of low voltage single-supply D/A converters (DACs) in the industry, which includes many leading products in performance and package size. A wide variety of applications use ADI precision nanoDAC® products because of their small footprint and robust range of features, including 8- to 16-bit resolution, low power, a fast 50 MHz SPI or 3.4 MHz I2C interface, and more, in a tiny package option. ADI’s nanoDAC+™ products offer enhanced features such as higher accuracy, improved dc performance, increased robustness, and lower glitch energy, among other advantages.
-
Product
DC/DC Converter 120 W
CTS-120-6874-D
-
DC/DC converter with 120 W from Premium | input ranges 43.2 - 90 VDC | output 12 V | operates in temperatures from -25 - +85 °C | designed according to EN50155
-
Product
- RS-485 to Fiber Optic Converter
Model 276A
-
FEATURES: Data Rate to 1 MBPS; ST Connectors; DB-25 Connector; Half-duplex operation; Extends distance of RS-485 network to 6,600 ft (2 km) on multimode fiber cable. The Model 276A provides the capability of transmitting an RS-485 signal via a fiber optic link.
-
Product
RF Converters
-
Typically designed for radar or wideband EMC test applications, our frequency converter modules are designed for the conversion between complex baseband waveforms and higher transmitted frequencies. These modules are ideal for integration with digitising modules.
-
Product
- Single Mode to Multimode Converter
Model 279
-
FEATURES: DC to 2.5 MBPS; Full duplex; 850nm to 1300nm; In line mounting; Small size; Data LED's; Line Loss switch; Single-mode distance to 20 Kilometers. The Model 279 provides transparent conversion between fiber optic devices utilizing multi-mode fiber and those with single-mode fiber.
-
Product
DALI 0-10v Converter
-
The DALI 0-10V Converter converts DALI signal to the Analog 0-10V protocol.
-
Product
DC/DC Converter 3.5 W
REM3.5E-2424S/R6/A/SMD
-
DC/DC converter with 3.5 W from Recom | input ranges 18 - 36 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | SMT package
-
Product
D/A Converters (DAC)
-
Analog Devices has the industry’s largest portfolio of D/A converters ranging from 8 bits to 24 bits. ADI DACs are unmatched in their ability to deliver performance and value by providing accurate and reliable conversion for a range of applications including industrial automation, programmable logic controllers, optical transceivers, data acquisition, and more. Our portfolio includes integrated output amplifier options for ease of use, dynamic range DACs for multicarrier generation over a very wide bandwidth, and a variety of other digital to analog converters to suit your design needs.
-
Product
DC to Synchro and DC to Resolver Converters
-
Computer Conversions Corporation
The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.
-
Product
mAEStro Audio Digital to Analog Converter
-
The mAEStro ADAC-100 receives AES/EBU (AES3) or S/PDIF digital audio and converts it to two channels of analog audio. It automatically detects sample rates up to 96kHz with low-jitter clock recovery. Two balanced line-level audio outputs are provided on XLR connectors on the rear panel. For convenient monitoring, a stereo headphone mini-jack and volume control are provided on the front panel.
-
Product
DC/DC Converter 3.5 W
REM3.5E-0524S/R10/A
-
DC/DC converter with 3.5 W from Recom | input ranges 4.5 - 9 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | 10 kVDC isolation
-
Product
Run Down Adapters
Screw RDA
-
The screw run down adapters are designed only for EZ-TorQ analyzer. These devices provide consistent and reliable torque readings for use with power-driven torque control tools. The RDA reduces the impact and irregular peaks that cause poor repeatability. The run down adapter is mounted in-line between the tool drive and transducer.
-
Product
High Performance DC/DC Converters
-
The 4:1 Input Voltage 1000 Watt Single FXP DC/DC Full Brick converter is designed to operate in parallel with up to 3 FXP bricks (2800 Watts) with no external circuitry. The FXP series provides a precisely regulated DC output. The output voltage is fully isolated from the input, allowing the output to be positive or negative polarity and with various ground connections.
-
Product
BCD to Binary Converter
BCD250
-
Computer Conversions Corporation
The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.
-
Product
Up/ Down Counters
-
LED display timer that can be used to time various situations and events such as talent, speakers, presentations, experiments, etc. The LED display has a brightness control and the 0.8" characters are large enough to be read across a room.
-
Product
Current Converter AC
NMTI 2
-
A modern multipurpose quantity-to-current loop converter designed for installation in switchboards.
-
Product
Pattern Converter for WGL/STIL to ATE
VectorPort
-
VectorPort is a versatile, low-cost test development tool for converting WGL or STIL vectors to targeted ATE tester formats, including pattern, timing, and pinmap data. VectorPort can read and write all major formats in both parallel (Flat) vectors and serial (SCAN) vectors.
-
Product
Single-Channel Voltage Output D/A Converters
-
Analog Devices offers a broad portfolio of single-channel voltage D/A converters, which includes many leading products in performance and package size, with resolutions from 8-bit to 20-bit, low power, and a serial SPI, parallel, or I2C interface. Within the industry’s smallest packages, we offer more functionality within smaller board and module sizes. The integration of a precision reference minimizes board area and costs, eliminates the need of calibration, and reduces the number of external components to simplify the design stage.
-
Product
Synchro to Digital-Resolver to Digital Converters
HSDC-HRDC
Digital / Synchro Converter
Computer Conversions Corporation
HSDC & HRDC Series are Miniature, Tracking Synchro and Resolver to Digital Converters with programmable resolution, 8/16 Bit data bus controls, continuous Built-In Self-Test report, and forced angle test modes used for functional validations on command for military and industrial applications.
