Product

DC/DC Converter 2 W

RHV2-0512S/R20

-

ELMA Electronic, Inc.

RHV2-0512S/R20 - ELMA Electronic, Inc.

DC/DC converter 2 W from Recom | input ranges from 4.5 - 5.5 VDC | output 12 V | operates in ambient temperature from -40 to +85 °C without derating

Product

Optical Path Converter

LS512A/LS512B

-

Lisun Electronics Inc.

LS512A/LS512B - Lisun Electronics Inc.

There are many LED manufactories using two integrating spheres and one spectrophotometer to do test. The previous testing way is: when you use big sphere to test, the customer need to connect the detector cable and optical fiber from the Spectrophotometer to the big sphere, after the calibrating and then you can do the test. When you use the small sphere, you need to take away the detector cable and optical fiber from the big sphere to the small sphere, then need to calibrate again. It is too troublesome to take out the detector cable and optical fiber between the big sphere and small sphere, and you need to calibrate again for every change. The frequent change will also shorten the life of the detector cable and optical fiber.

Product

DC/DC Converter 4000 W

700DNC40-24

-

ELMA Electronic, Inc.

700DNC40-24 - ELMA Electronic, Inc.

Power supply DC/DC | 4000 W

Product

16 or 32 channel Digital to Analog Converter

LS-71-P

-

Lumistar Inc.

LS-71-P - Lumistar Inc.

The LS-71P PCI D/A Converter (DAC) board provides high speed analog outputs of PCM decommutated data allowing real time data displays using strip chart recorders or similar devices. The LS-71-P board is designed to be used in conjunction with the Lumistar LS-50-P Multifunction PCM Decommutator boards and uses an over-the-top communication bus directly from the decom to the DAC to avoid any glitches in the analog outputs due to PCI bus activity. Direct “mailbox” type access is also provided to allow the user to send information through the PCI bus to the DACs. The DAC board design allows 2 LS-50-D Multifunction decom boards to be used with a single DAC board allowing tagged data from either data stream to be directed to any DAC channel. An optional LS-71-DB Word Selector Daughterboard allows two additional data streams to be monitored with the ability to select channels from 4 data streams to be displayed on any DAC channel. The design incorporates an extremely large memory (more than 200,000 16-bit words) used as a lookup table allowing linear or non-linear EUconversions with constant delay regardless of the number of polynomial coefficients required. Standard product supports a single decom, however, dual decom support is available as an option.

Product

Interface Converter

ZET 7070

-

ZETLAB Company

ZET 7070 - ZETLAB Company

Basic delivery scope with digital transducers for laboratory use includes the following: interface converter ZET 7070, power supply module 220V→ +24V, measuring line connector ZET 7001 (these components are mounted on a din-rail 300 mm); cable USB 2.0 A→B – length 1,8 m; terminal resistance 120 Ohm (for industrial use — steel plug); CD with  ZETLAB SENSOR software, enabling connection of up to 60 digital sensors; set of operational documentation.

Product

Thermal Voltage Converter

1395D

-

Ballentine Laboratories, Inc.

1395D - Ballentine Laboratories, Inc.

The 1395D series of TVC's, have Dual Thermal Element technology. The 1395D offers double the output voltage (typically 14 mV instead of 7 mV). This higher output voltage means better resolution and increased accuracy. It can be used to measure AC Voltages between 20 Hz and 100 MHz and it can serve as a primary AC voltage standard and/or standard for calibration of AC calibrators and voltmeters.

Product

DC to Synchro and DC to Resolver Converters

-

Computer Conversions Corporation

Computer Conversions Corporation

The LDS 500M Series are high accuracy, drift free, and continuously updating DC-Angle to Synchro or Resolver Converters designed for Military and Industrial simulation and control applications.

Product

RTAX/RTSX Netlist Converter

-

Aldec, Inc.

Aldec, Inc.

RTAX/RTSX EDIF and PDC/PIN Converter combines two functions supporting Aldec RTAX prototyping - it provides EDIFs netlists conversion and PDC/PIN constraints file remapping for two families RTAX-S/SL and RTSX-SU/S, SX-A. RTAX/RTSX EDIF and PDC/PIN Converter performs automatic conversion of the RTAX-S/SL and RTSX-SU/S, SX-A EDIFs netlists to ProASIC3/E EDIF netlist, which means replacement of the PLL and memory primitives has to be done, with consideration of the limitations caused by the differences between RTAX-S/SL, RTSX-SU/S, SX-A and ProASIC3/E technologies.

Product

Testing Hardtop Convertible

-

Magtrol Inc.

Magtrol Inc.

Magtrol designed this Custom Motor Test System for the testing of motors used in hydraulic systems in hardtop convertible roof drives.

Product

DC/DC Converter 140 W

CTS-120-6887-D

-

ELMA Electronic, Inc.

CTS-120-6887-D - ELMA Electronic, Inc.

DC/DC converter with 140 W from Premium | input ranges 21.6 - 47 VDC | output 24 V | operates in temperatures from -25 to +85 °C | designed according to EN50155

Product

HPx-346 Analogue to Network Radar Converter

-

Cambridge Pixel Ltd.

Cambridge Pixel Ltd.

The HPx-346 is a small form factor, combined analogue radar input and network radar video distribution unit. The unit connects to the analogue video interface on a radar, digitises the data and distributes it as UDP packets over Ethernet.

Product

Data Converters

-

MaxLinear

MaxLinear

Exar offers a family of 8-bit and 10-bit triple Digital-to-Analog Converters (DACs) ranging from 100Msps to 180Msps. These high-speed DACs are optimized for use in video, display and graphics applications.

Product

Transition Time Converter, 150ps

15435A

-

Keysight Technologies

15435A - Keysight Technologies

The new design of these transition time converters ensures very low signal reflection far beyond the 3 dB point, unlike conventional converters.Reducing the signal transition-times also increases the overall pulse-performance for overshoot/reflection sensitive applications.The converters are fitted with SMA connectors, one male, one female.

Product

I/O's & Converters

-

Rishabh Instruments Pvt. Ltd.,

Rishabh Instruments Pvt. Ltd.,

Module of logic outputs. Control of actuators from monitoring systems or PLC over RS485. 4 relay outputs or 8 OC outputs steered through RS-485/Modbus. Fixing on a TS35 rail. Full galvanic separation between outputs (for relay outputs). Configuration through free LPConfig software.

Product

Data Converters

-

Omega Engineering, Inc

Omega Engineering, Inc

Omega carries an extensive line of data converters, including RS-232 to USB interface converters, fully isolated RS-232 to RS-485 converters, industrial ethernet to serial device servers, and more.

Product

Serial-to-Ethernet Converter

MultiNet

-

GE Vernova

MultiNet - GE Vernova

MultiNet is a communications module that provides GE Multilin serial ModBus IEDs with ModBus TCP/IP communications over Ethernet, allowing connection to fiber optic LAN and WAN network systems. MultiNet has the capability to connect up to 32 serial ModBus devices eliminating complex wiring and additional communications converters, and providing a streamlined and economical Ethernet hub.

Product

Signal Converters For Temperature Measurement In Direct Drive Motors

EIB 5000 series

-

Heidenhain Corp.

EIB 5000 series - Heidenhain Corp.

*Reduced cabling*Overload protection for direct drive motors*Faster response behavior for excessive temperatures*Greater cost-effectiveness

Product

DC to LVDT and DC to RVDT Converters

-

Computer Conversions Corporation

Computer Conversions Corporation

The SLVT Series are complete, low profile, continuously updating, single channel, Isolated Digital to LVDT Converters used to simulate the output of LVDT's (Linear velocity displacement transducers), RVDT's (Rotary...) and other phase/voltage sensitive AC devices. They provide a very precise linear AC voltage output proportionate to the magnitude of the input data, in or out of phase respective of the AC reference input as determined by the MSB of the input word (offset binary format).

Product

Modbus Register Converter

Model 2390

-

ICS Electronics

Model 2390 - ICS Electronics

* Converts Modbus Registers and variables for replacement Modbus devices.* Maintain existing software when upgrading Modbus systems.* Provides serial control of Modbus RTU devices from any ASCII source.* User defined Register Conversion Table supports all Modbus RTU devices.* Internal Register Conversion Tables for Watlow F4-to-EZ-ZONE and F4-to-F4T conversion.* Serial ports support RS-232 and 2-wire/4-wire RS-485 signals.* Includes baud rate conversion capability.* Uses SCPI commands to load the Conversion Table and set serial settings.* Small metal case mounts on a DIN rail or on any flat panel.* 239x Table Loader Program uploads the 2390 Register Conversion Table from an Excel csv file.* 239x Serial Keyboard Program provides instant control of the 2390 and Modbus Slave Devices without writing a program.

Product

- RS-232 to RS-422/RS-485 Converter

Model 285

-

Telebyte, Inc.

Model 285 - Telebyte, Inc.

FEATURES: User Selectable RS-422 or RS-485; User Selectable 2 or 4 Wire RS-485; Intelligent Control Of RS-485 Transmitter And Receiver; TD & RD LED's; DTE/DCE Compatible; Data Rates Up to 64 KBPs. The Model 285 RS-232 to RS-422/RS-485 Converter is a unique interface converter that can be configured to operate in compliance with RS-485 or RS-422 equipment, and RS-232.

Product

BCD to Binary Converter

BCD250

-

Computer Conversions Corporation

BCD250 - Computer Conversions Corporation

The BCD Series of BCD to Binary Converters will convert 4 digits of scaled BCD angle data with a full scale of 359.9degrees into 12 Bits of binary angle data (MSB=180degrees). These units are entirely digital, require no timing or control signals and do this conversion in less than 500 nano-seconds. Logic levels are TTL/DTL compatable and +5V DC power is required. They are packaged in a 2.6 x 3.1 x .82" H PC board mounting module.

Product

Mini Optical To RF Converter

MX-O2RF

-

Maxcom Inc.

MX-O2RF - Maxcom Inc.

The Maxcom MX-O2RF series optical receivers are versatile, low-cost and compact optical receivers are versatile, low-cost and compact optical receivers for use as a tool for test and measurement

Product

DC/DC Converter 3.5 W

REM3.5E-1224S/R6/A/SMD

-

ELMA Electronic, Inc.

REM3.5E-1224S/R6/A/SMD - ELMA Electronic, Inc.

DC/DC converter with 3.5 W from Recom | input ranges 9 - 18 VDC | output 24 V | operates in ambient temperature from -40 to +95 °C | SMT package

Product

Vector And Scalar Mixer / Converter Measurements

S95083B

-

Keysight Technologies

S95083B - Keysight Technologies

The Keysight S95083B measurement software includes the scalar mixer / converter plus phase (SMC+Phase) measurement class. It provides fully calibrated conversion gain / loss, relative phase, and absolute group delay measurements of mixers and converters without the need for reference or calibration mixers. Eliminating the calibration mixer requires a U9391C / F / G comb generator and an external DC power supply. A vector mixer characterization (VMC) is also included for measuring group delay of frequency-converting devices. VMC can be used to characterize a user-supplied calibration mixer.

Product

Multichannel Voltage Output D/A Converters

-

Analog Devices Inc.

Analog Devices Inc.

Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the availability of multiple independent output spans, system calibration functions that allow user-programmable offset and gain, or D/A converter increment/decrement functionality, which reduces the need to add external precision gain stages and facilitates the use of this family of D/A converters.

Product

Ethernet Media Converter

MC-E Series

-

GE Vernova

MC-E Series - GE Vernova

The MultiLink MC-E series makes it easy to use the power of optical fiber for extending Ethernet networks to remote locations. The fiber port is available in a variety of connector types and can support extremely long distance connections of up to 40km. With a built-in 2 copper port switch, it's also the fastest way to add multiple Ethernet drops to remote locations.