Bare Board Testers
check unloaded PCBs for opens, shorts, leakage and voltage breakdown.
See Also: Bare Board, Bare Board Test, Bare Board Probes, Bare board Fixtures, PCB
-
Product
Multifunction Installation Tester
COMBI519
-
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
Product
Digital Clamp Tester (CE)
M-2100
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Wide current measurements with tear drop type 55mmφCT up to 2000A.*Data-hold and Auto power off function.*Additional AC/DC voltage, resistance, diode test, continuity check.*Conform to IEC safety requirements.
-
Product
Socket Tester with RCD Tripping
-
Shanghai Beha Electronics Co., Ltd.
*Mains wiring polarity check.*ELCB/RCD testing.*Measuring ear for line current.*Measuring ear for leakage current.*Helps calculate insulation resistance.*Helps calculate power consumption.*Helps fault finding of standing earth fault.*Fused main adapter.*Appliance testing (with the ad of a clamp meter).
-
Product
PCI Data Acquisition Boards
AD8CH12B-100DMA Series - Single low-spur 8-bit, 100 MS/s
-
Model AD8CH12-100DMA has eight simultaneous-sampling 12-bit A/D converters, and can continuously acquire and transfer hundreds of megabytes or even gigabytes of A/D data directly into host system memory at up to 100 MB/s, via 64 or 32 bit PCIbus DMA. It can acquire and transfer eight 8-bit A/D channels at up to 12.5 MSPS each (100MB/sec aggregate), or eight 12-bit A/D channels at up to 6.25 MSPS each, or four 8-bit channels at up to 25 MSPS each, or four 12-bit channels at up to 12.5 MSPS each.
-
Product
Intelligent and Unidirectional Scrape Tester
ZDG-25
-
Shanghai Dean Electrical Co., Ltd
Executive standard: GB/T4074.3-2008/IEC60851-3Inspection standard: JB/T4279.9-2008Meet GB/T6109-2008 standard requirementsUsed to test the film scrap resistance of enamelled round wires with nominal conductor diameter above0.250mm;Application of SCM control，enter the weight value, operation will be completed automatically: put down the scraping rod, stop while film scratch, calculate and show the scraping force, raise the scraping rod, return to zero, sample rotates 120°and repeat the same operation, calculate and show the scraping force of three times and average scraping force.When film is scratched, film scraper would automatically stop scraping, with exposed conductor of sample＜3mmWith the advantages of high sensitivity, good repeatability, stable and reliable characteristics.
-
Product
12V Battery Tester
1957
-
Peaceful Thriving Enterprise Co Ltd
Voltage / battery / alternator multi tester for all 12V DC systems.
-
Product
Built-in LED Gem Tester
-
Fuzhou Zhongtuo Optoelectronic Co.,Ltd
Gem Tester Refractive index is one of most important optical parameter. Gloss of gem can be estimated by the parameter.The kinds of gem can be precisely determined in accordance with the measured value of refractive index because every kind of gem has its inherent refractive. Besides, index of double refraction can be also measured. Through the parameter you can judge whether a gem is uniaxial or biaxial photopositive or photonegative.
-
Product
Battery Capacity Testers|Discharge Testers
-
DV Power offers a wide range of battery capacity testers to meet specific customer needs. All of them are portable, powerful and most of all universal. Any battery string, such as lead-acid, lithium-ion, nickel-cadmium based and others, with voltages in the range of 0,9 – 800 V DC can be tested in an accurate, user-friendly way.The capacity test is carried out following the battery testing standards: IEEE 450-2010, IEEE 1188-2005, IEEE 1106-2015, IEC 60896-11/22, and other relevant standards.BLU battery testers enable setting the discharge current up to 350 A, with 0,1 A resolution. If higher currents are required, several units can be connected in parallel, or BXL additional load units can be used. Discharge parameters can be monitored in real-time during the capacity test. Overall battery voltage, current, elapsed test time and capacity will be presented during the entire test on a touch screen display.
-
Product
PCI Digital I/O Boards
PCI-P16POR16
-
16 Channel Isolated Digital Input, 16 Channel PhotoMos Relay Output. Includes CA-4037W cable and two CA-4002 D-Sub connectors
-
Product
Adhesion Testers
-
Adhesion testing is the best way to determine whether your films and coatings adhere to substrates the way you need them to.
-
Product
5G Radio Communication Tester
CMX500
-
The R&S CMX500 radio communication tester is the future-proof solution for 5G NR testing, featuring an intuitive and flexible web-based user interface, the R&S CMsquares. Supporting manual interactive operation as well as automatically sequence-controlled test protocols makes the R&S CMsquares an advantageous software solution, with unique modules for all signaling use cases. These range from R&D design stages up to end-to-end application testing, production and conformance tests. The introduction of a one-platform strategy for all 5G NR test equipment enables a unified test environment for signaling and non-signaling testing through all stages of 5G device production.
-
Product
Clamping Voltage Tester
MIG0603CLV2
-
The MIG0603CLV2 is a generator for clamping voltage testing of varistors. It has circuits with four different source impedances and up to 15 different measurement ranges. The instrument is used to perform varistor clamping voltage tests on up to 1000 V varistor types. The test impulse is a 8/20µs current waveform up to 500A which is maintained over the entire load range.
-
Product
Composite 1×24 Video Distribution Amplifier Board
BL-VDA124-01
-
Video Distribution Amplifiers (sometimes called a video splitter – not to be confused with a video split screen controller such as our PXD510E split screen controller) are typically used for connecting a camera or other video source to several monitors that do not have “looping” inputs. In this situation, each monitor has a permanent 75 ohm termination. With two non-looping monitors connected together, the line would be double loaded and result in a dim picture on each monitor. Using a Video Distribution Amplifier will solve this problem by driving each monitor individually at 100%.
-
Product
Website Tester
-
Find out how well your site works across mobile and desktop devices. Test how mobile-friendly your site is. Test your site for mobile friendliness, mobile speed, and desktop speed.
-
Product
Bench Hardness Tester
-
*Digital rockwell hardness tester*Operating Rockwell hardness testing of hard alloy, carbon steel, alloy steel and non ferrous metal.*High digital display resolution*Easy operation with auto loading and unloading of test force, and auto holding of test force.
-
Product
Horizontal Flammability Tester
-
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
Product
Micro-Ohmmeter and Loop Resistance Tester
LRT 6000
-
LRT 6000: The right solution for impedance resistance measurement in compliance with all aircraft specifications on plane, helicopter, rocket, army vehicles for both production andmaintenance. It is a very easy-to-use and versatile instrument. Its ergonomics allow the user to use it either placed on the ground or across one's shoulder or chest. Awide back-lit LCDdisplay combinedwith an intuitive keyboard ensures simple and easy operation.
-
Product
Iron Core Earth Tester
-
Weshine Electric Manufacturing Co., Ltd
Transformer iron core grounding current tester is a high-precision clamp meter specially designed for measuring AC leakage current, current and voltage. Large diameter (80×80mm) can clamp φ80mm cable, or 96mm×4mm flat steel ground wire, suitable for cables Leakage detection and transformer grounding flat steel leakage measurement.
-
Product
Trailer Tester
Inspector 930
-
The Inspector 930 trailer tester is a complete, all-in-one trailer diagnostic system which simplifies ABS, brakes, air, lights, and electrical testing. It provides the ability for a single technician to perform a full inspection in one trip around the trailer.
-
Product
Handheld Return Loss Tester
JW3308
-
Shanghai Joinwit Optoelectronic Tech,co.,Ltd
JW3308 handheld return loss tester is used to measure the return loss in the field fiber optic linking, in order to adjust the quality of the optic fiber end-face, and to make sure the fiber optic communication is in good condition. This 3308 handheld return loss tester can realize measurement of Return Loss, Insertion Loss, Output power, and also can be used as the laser source. Moreover, it has the data storage function of 500 measurement items.
-
Product
Voltage Tester
SG5003A
-
Wenzhou Zhengyuan Electronic Co., Ltd.
Digital live-wire voltage reading
-
Product
Leak & Seal Integrity Tester
-
Saicheng Leak Tester is professionally designed for the leakage tests of packages, bottles & pouches for food, drugs, medical instruments, household chemical products, cars, electronic components, stationeries and other industrial products. The instrument also can be used to test seal performance of specimens after falling and compression tests.
-
Product
Tribometers & Mechanical Testers
-
Research into materials and how materials can be changed to influence strength, integrity, or durability is an integral part of product design and improvement across nearly every industry.
-
Product
Single Board Computers
-
We produce a range of ‘off-the-shelf’ SBCs that feature some configurable elements, providing enough flexibility for most applications. Alternatively, if our off-the-shelf single board computers do not suit your requirements, we can design a custom solution just for you at a lower cost and commitment than you might expect.
-
Product
Elasticity, Bend & Impact Testers
-
The performance of coatings when influenced by external stresses caused by stretching, bending or impact, determines their suitability for their designed application. A coating designed for use in the coil coating industry, for example, should have the ability to stretch as the substrate is formed into its desired shape without damage.
-
Product
DMX Tester
DXT1
-
The new DMX Tester from NuDelta Digital is a feature-packed test tool you won't want to leave home without. It can send any level to any DMX address with simple commands similar to those found on the world's most popular lighting consoles. It can test for valid DMX signal and show you the level at any address. It can test continuity on all five pins of a standard DMX cable and indicate which pins are not connected or cross-wired. Runs for hours on a 9 volt battery (included).
-
Product
Battery Internal Resistance Tester
FST-7000
-
Foresight Electronics Co., Ltd.
Battery Conductance Tester is a portable digital measurement device for testing lead acid stationary batteries health and aging condition precisely within seconds. With the help of this device either single cells / blocks or large, multi group battery banks can be measured within a short time and the precisely measured data are processed and reported by given analyzer software automatically.
-
Product
Insulation Tester
AD-225
-
3 Measurement voltage range: 500 V; 1000 V and 2500 V, Control of measuring voltage during measurement, Insulation measurement up to 100 G W, Elimination of trough resistance insulation ? 3 connectors measurement method, Autoranging,
-
Product
Socket Testers
-
Socket Testers including 4 Pole RV Output Socket Tester, Blade Socket Tester, 7 Pole Plug Output Tester, 7 Pole Socket Output Tester.
-
Product
Ink Rub Tester
RT-01
-
Ink Rub tester, also known as abrasion resistance tester, using ASTM D5264 and is designed to measure the ink resistance against rubbing on packaging materials. RT-01 Ink Rub Tester is designed for the abrasion resistance of surface coating layers of printed materials, such as ink layer or photosensitive coating.
