Circuit Board
-
Product
Noise Board
332D-11 VG
-
This printed circuit board was designed to original specifications and contains OEM specified parts. This board is required for testing the 332D-11 series gyros. Also contained on board is the Method A type calibration and sample and hold circuits required to perform the calibration of the noise circuits.
-
Product
LC-4.5 Voltmeter
5203
-
Model LC-4.5 is the first hand-held voltmeter to include a number of special features which facilitate corrosion and cathodic protection testing on underground structures. It is designed for field testing under almost any environmental conditions. Sealed Mil Spec. switches, sealed windows, a gasketed case and a printed circuit board with baked-on moisture and fungus resistant coating on both sides make this possible.
-
Product
Design, Manufacture & Test of Complex RF/Microwave Printed Circuit Boards (PCBs)
-
Teledyne Labtech specialises in the design, manufacture and test of complex RF/Microwave printed circuit boards (PCBs). - Technology driven – we innovate- Turnkey - one stop for manufacture, assembly & test- Focused – technical design support for RF/microwave and large format PCBs
-
Product
Failure and Technology Analysis
-
Failure analyses in order to clarify the failure cause soonest possible.From single device to the whole system - and from highly complex IC up to printed circuit board (PCB), mounting & interconnection technology and printed board assembly (PBA).
-
Product
3D Solder Paste Inspection (SPI)
-
Systems designed for solder paste inspection (SPI) quickly and reliably check the solder paste deposits on the circuit board.
-
Product
Single Front Slot Universal Low-Profile PCI to PCMCIA Adapter, Black Bezel
P313B
-
To cater to the latest generation of low-profile PCs that can only use low-profile PCI add-in boards, Elan has created the P313. This model, from the P-series range, features a PCMCIA Type III 3.5" drive bay mounted slot and a circuit board that conforms to the MD1 profile specification. It will allow you to use any TypeI/II/III PCMCIA card.
-
Product
Mechanical Fixtures Available w/ESD Plates & ESD Pressure Pins
-
H+W Test Products has developed a series of inexpensive mechanical test fixtures. These fixtures are designed for testing low volume runs of printed circuit boards or prototype applications requiring approximately 150 test points.
-
Product
PWB Interconnect Stress Test
-
PWB Interconnect Solutions Inc.
Services to test the reliability of Printed Circuit Boards. PCBs).Coupon Inspection and Electrical Prescreen. Coupon Testing. Failure Location via I/R Photo Imagery. Failure Analysis.
-
Product
Test Points
TestStation LX2
-
TestStation LX2 is Teradyne's largest pin count in-circuit test system. Configurable up to 15,360 pins, TestStation LX2 utilizes the new UltraPin II 128HD pin card for testing large, complex, and heavily-integrated printed circuit board assemblies.
-
Product
PXI-2535, 544-Crosspoint, 1-Wire PXI Matrix Switch Module
778572-35
-
544-Crosspoint, 1-Wire PXI Matrix Switch Module—The PXI‑2535 is a high-density 4x136 PXI matrix switch module that is ideal for routing low-power DC signals in validation test systems of mass produced devices such as semiconductor chips and printed circuit boards (PCBs). Featuring field-effect transistor (FET) relays, the PXI‑2535 offers unlimited mechanical lifetime and switching speeds up to 50,000 crosspoints/s. It also features onboard relay counting for relay monitoring and deterministic operation with hardware triggers to improve test throughput.
-
Product
Metal Alloy Low-Resistance Resistor: ACQ-200
LRA
-
*This specification is applicable to lead free, halogen free of RoHS directive for metal alloy low-resistance resistor.*This product is for general purpose.*LR-A series : AEC-Q200 qualified available.*Miniature size suitable for compact Print Circuit Boards of high-precision electronic products.
-
Product
Switch Probes
-
A Switch Probe is a spring contact probe and receptacle combination that is normally open, and after a designated travel the switch probe closes. The most common use for switch probes is in the cable harness testing industry. The switch probe is used to verify the correct location of a terminal in a connector while checking the retention force as well. Switch probes also verify the presence of nonconductive components such as caps for connectors or devices on a circuit board. Smiths Interconnect offers three standard sizes of switch probes.
-
Product
EDA Software
-
Shorten design cycles to achieve first-pass design success. Our next-generation integrated electronic design automation (EDA) software provides engineers with new tools and enhancements to bring efficiencies into their printed circuit board (PCB), RF and microwave, 5G / 6G, and high-speed digital design flows.
-
Product
SSMB Connectors
-
Pasternack SSMB connector category has several part numbers, most are RoHS and REACH compliant. SSMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our SSMB connectors are built to precise microwave and RF industry specifications. Connectors with SSMB series are manufactured in jack or plug gender with 50 Ohm impedance. SSMB connector items are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These SSMB connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products at Pasternack, this SSMB connector series is in-stock. Not just in stock, but these connectors also will ship the same day as they are purchased.
-
Product
Line Scan Camera
8M Series
-
The USB Line Camera 8M is an easy-to-use cost-effective board-level line scan camera. It consists of two circuit boards, the main circuit board and the sensor circuit board.
-
Product
Wave Soldering Machines
-
Shenzhen Leadsmt Technology Co.,Ltd
A bulk soldering process used for the manufacturing of printed circuit boards.
-
Product
Semiconductor & Flat Panel Display Inspection Microscopes
MX63 / MX63L
-
The MX63 and MX63L microscope systems are optimized for high-quality inspections of wafers as large as 300 mm, flat panel displays, circuit boards, and other large samples. Their modular design enables you to choose the components you need to tailor the system to your application. These ergonomic and user-friendly microscopes help increase throughput while keeping inspectors comfortable while they do their work. Combined with OLYMPUS Stream image analysis software, your entire workflow, from observation to report creation, can be simplified.
-
Product
Silicon Nails Feature, GTE 10.00p
K8214A
-
Keysight’s Silicon Nails feature enables all the tools required to develop and execute tests on non-compliant boundary scan devices that are connected to boundary scan compliant devices on the printed circuit board.
-
Product
TTL/I2C/SPI Expansion Kit
OP-SB85L
-
OP-SB85L is the interface expansion kit that has a port to measure TTL / CMOS signal level communications, and the one to measure the voltage of high-speed analog input. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communication between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI on monitoring and simulating.
-
Product
Flex Test Fixtures
-
FTFs are test fixtures which are dedicated for testing flex-based components and assemblies such as displays, touch panels and more. A weak spot in a typical functional test system is the method to connect DUT flexible cable to a circuit board where the simple method of attaching the flex directly with an ZIF or LIF connector fails.
-
Product
75 Ohm MCX Connectors
-
Pasternack 75 Ohm MCX connector category includes several part numbers, the majority are RoHS and REACH compliant. 75 Ohm MCX connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These 75 Ohm MCX connectors are built to precise RF and microwave industry specifications. MCX 75 Ohm connectors are available in jack or plug gender with 75 Ohm impedance. 75 Ohm MCX connector products are available in straight or right angle versions, as well as, bulkhead or mountless options. These 75 Ohm MCX connector designs include crimp/solder or solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave products from Pasternack, this MCX connector series for 75 Ohm is in-stock. Not only are they in stock, these MCX 75 Ohm connectors will ship the same day as purchased.
-
Product
Circbord
8019
-
VECTOR Electronics and Technology, Inc.
2-sided board, circuit pattern on both sides, holes plated thruIdeal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. Solder coated pattern on both sides of board. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.
-
Product
Appliance/Tool Tester
-
FISHER TESTERS AUTOMATIC TEST EQUIPMENT
• Touch Screen Interface• Windows® 10 Pro• High Reliability with Proven Design• Lowest Board Count In Industry• No Proprietary Circuit Boards• USB Interface – No I/O boards in Computer• Remote Control Software for Factory Diagnostics/Updates• Full Network Compatibility• Integral Statistical Reporting• Test Data May be Stored in Multiple Formats• Two Year Warranty on Electronics
-
Product
Advanced Digital Lab Trainer
-
Designed to do experimentation with Digital & Analog circuits in the laboratory. It is a self contained trainer including Fixed & Variable DC Power Supplies, Pulse Generator with TTL/CMOS, Pulsar switches, etc In a single unit. It is very useful in project work and testing. A number of ready to use experiment circuits boards are available(Optional).
-
Product
Pogo Pin
-
Probe pin is also known as pogo pin or spring probe. It is designed to test the connection between two circuit boards and devices or equipment under test.
-
Product
Miniature 8-channel photon counter
id150 SERIES
-
Intended for large-volume OEM applications, the id150-1x8 is the only multichannel solid-state single photon detector on the market. It consists of a CMOS silicon chip packaged in a standard TO8-16pin header with a transparent window cap. The chip combines 8 in-line single photon avalanche diodes that can be accessed simultaneously for parallel processing. square in center-to-center A fast active quenching circuit is integrated within each pixel in order to operate each diode in photon counting regime. The chip is mounted on a printed circuit board on top of a single-stage thermoelectric cooler (TEC). A thermistor can be used to measure the temperature of the chip. Only two low power supplies of +5V and -25V are needed for operation in photon counting mode. The fast active quenching circuit leads to a dead time of less than 50ns per channel. An outstanding timing resolution of less than 60ps allows high accuracy measurements.
-
Product
Manufacturing Defects Analyzer
eloZ1-400
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the very latest generation, reliably detecting connection and assembly faults on printed circuit board assemblies. The eloZ1-400 is the compact version of the eloZ1. It is particularly suitable if there is only limited space to fit test appliances. The eloZ1-400 can also be used as a mobile test system.
-
Product
Automated Optical Inspection (AOI)
-
Automated optical inspection (AOI) is an automated visual inspection of printed circuit board (PCB) (or LCD, transistor) manufacture where a camera autonomously scans the device under test for both catastrophic failure (e.g. missing component) and quality defects (e.g. fillet size or shape or component skew). It is commonly used in the manufacturing process because it is a non-contact test method.
-
Product
Clamshell Type Mechanical Fixtures
Series 71
-
The VP Series 71 dual well mechanical kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface and the advantage of testing two devices. This can be similar devices, or devices that are used together in a functional test. The VP Series 71 Kits have the same available features and options as the Series 70 Kit and are available with or without the ITA G12 Interface.
-
Product
Power Bus
MS 1606
-
The PowerBus is used to service printed circuit boards, instruments and systems, which has Micro controller / Microprocessor. The PowerBus has RS232 Communication for PC interface. The PowerBus connects to the UUT through the microprocessor / micro controller socket. The UUTs microprocessor / micro controller is removed from the UUT and it is replaced by the PowerBus. The Power Bus adapts microprocessor specific function as pin layouts, status / control function, interrupt handling, timing and memory and I / O addressability.
