Circuit Board
-
Product
Detector And FPA Testing
-
The FPA Test Set (FPATS) interface to the detectors under test (DUT’s) is via a custom pedestal plate which provides both a conductive heat path to both the individual DUT’s as well as the field of view limiting aperture plate. This custom pedestal plate protrudes through the customer provided DUT interface printed circuit board (PCB) and makes physical contact with the rear of the DUT packages and the aperture plate when the FPATS is in the closed position. The pedestal plate is mounted to the ambient source plate and its temperature is actively driven by this subsystem.
-
Product
Expanding In-Circuit Capabilities
-
Circuit Check supports reading linear bar codes and 2D symbols within each of its fixture product lines.When spring-loaded probes are not practical or access is limited, Circuit Check can help you with thru-connector tests to contact connectors on any surface or edge of a circuit board. These tests can be implemented spring probes, mating connectors, sacrificial SMT connectors, and stabber cards.
-
Product
In-Circuit ESR & DCR capacitor Tester
236
-
This In-circuit ESR & DCR capacitor tester is designed to measure ESR (equivalent Series Resistance) on capacitors range from 0.47uF to 2200uF, in or out of circuit. The ability to trouble shoot in-circuit saves time and makes the 236 a must for anyone that tests or trouble shoots PCB (printed circuit boards).
-
Product
Test Hardware
-
Development of additional hardware components in-houseCreation of the layout of the developed circuit boards and subsequent production outside the companyAssembly of the printed circuit boardsCreation of additional circuits for test adapters
-
Product
Heavy Board & Heavy Board
Protector Lever Actuated Clamshell
-
Designed for testing heavy massive boards. Boards with heavy components like large transformers and inductors can destroy normal test fixtures. This design utilizes a 3 plate system where an internal lever actuated sub plate containing the test pins raises to probe the circuit board when the handle is pulled. Heavy boards can bend and break exposed test pins. Similarly large boards which need to be probed by very small delicate test pins can also benefit from this protected test fixture design. This fixture is recommended in situations where there is a high board mass to pin size ratio and pin protection is required. Front and rear panel modular inserts allow for easy updates and customizations to the user hardware interface.
-
Product
Circbord
8022
-
VECTOR Electronics and Technology, Inc.
Single sided board, circuit pattern one side only, holes not plated thru.Ideal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges.
-
Product
Control Board for Motor, Pump & Valve
F1V04
-
Beijing SANKI Petroleum Technology Co., Ltd.
The main board issues a start signal and a low voltage signal (12v) for opening the electromagnetic valve, which are converted into strong voltage signals (220 VAC) to drive the electromagnetic valve (380 VAC) and the motor in our fuel dispensers system, thus completing the function of conversion from weak voltage power to strong voltage power. The control board circuit isolates high voltage interference signals via photoelectrical isolating components.
-
Product
1.0/2.3 Connectors
-
Pasternack 1.0/2.3 connector category has many part numbers, most are RoHS and REACH compliant. 1.0/2.3 connector series in this category will terminate to coax or PCB (printed circuit board). Our 1.0-2.3 connectors are built to precise RF and microwave industry specifications. 1.0-2.3 connector series is manufactured in jack or plug gender with 50 Ohm impedance. 1.0-2.3 connectors are available in straight or right angle versions, as well as, bulkhead or mountless options. These 1.0 / 2.3 connector designs include crimp/solder, solder or solder/solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this 1.0/2.3 connector series is in-stock. Not only are these 1.0-2.3 connectors in stock, but they ship the same day as they are purchased.
-
Product
Monitor SDR Boards
-
Multiple Access Communications Ltd.
MAC Ltd’s MONITOR product family includes a number of software-configurable digital signal processing platforms intended for use in radio frequency (RF) receiver and transceiver applications. The MONITOR products are available in assembled printed circuit board (PCB) form for integration into larger systems. They also form the basis of MAC Ltd’s CatchAll™ radio products. In addition to the standard products listed below, MAC Ltd is happy to discuss the customisation of existing products and/or the development of new bespoke hardware and software.
-
Product
Trimmer Potentiometers
-
CTS trimmers are typically used in applications that do not need frequent adjustment and are often used for "set and forget" initial adjustments in circuits. These are usually located on the circuit board and out of view. CTS trimmers are available in a variety of standard resistance values, tolerances, power ratings, and mounting styles. Depending on product series, adjustment knobs are available with color coding and a screwdriver and/or hex hole for top or bottom side adjustments.
-
Product
Extender
3690-17
-
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards. Receptacles have double row phosphor bronze contacts with high quality, long life mounted on top of the extender.
-
Product
Dip Coating Systems
-
SCS Dip Coating systems, which are available in free-standing floor or tabletop models, are specifically designed for production applications that do not require large in-line systems. SCS dip coating systems can be used to apply a range of coatings, as well as photo-resists and solder masks, that are part of printed circuit board applications all with a level of precision that manufacturer's demand. Both SCS models include a host of features that make them an ideal choice for lab and production operations.
-
Product
Mini SMP Connectors
-
Mini SMP connector series, also known as SMPM connectors, are ultra-miniature, high frequency connections commonly used in applications up to 65 GHz. Mini-SMP connector category will terminate to coax or PCB (printed circuit board) and many mini-SMP connectors are hermetically sealed. Pasternack mini SMP connectors are built to precise microwave and RF industry specifications and many are RoHS and REACH compliant. SMP mini connector products are built in male or female gender with 50 Ohm impedance. Mini-SMP connectors are available in straight or right angle versions, as well as, mountless options. These Mini-SMP connector designs include solder attachment methods. As with the other over 40,000 RF, microwave and millimeter wave components from Pasternack are in-stock. Not only in stock, but these SMP mini connectors will ship the same day as they are purchased.
-
Product
Panelized PCB Tester
-
Removable nests are designed to configure base test system to accept panelized circuit boards for rapid functional test.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
-
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
PXI 16 x SPDT Reed Relays
40-110-021
-
The 40-110/115 range of switching modules are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 96 pin male micro-D connector. General purpose reed relays are used for the construction of small switching networks or for slaving up to larger switches.To simplify inter-relay wiring, interconnection points are built onto the circuit board thus easing the construction of complicated wiring.
-
Product
6 Sided Bed of Nails Testers
BoxProber Family
-
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
Product
Manufacturing Defects Analyzer
eloZ1-1600
-
The eloZ1 Manufacturing Defects Analyzer is an in-circuit tester of the very latest generation, reliably detecting connection and assembly faults on printed circuit board assemblies. The eloZ1 can be integrated into table systems as well as into inline-systems.
-
Product
PXI 8x4 Power Matrix, 2 Pole
40-550-002
-
Connections are made via a front panel 37-way D-Type male connector or two 20-way GMCT male connectors. Used for switching inductive/capacitive loads up to 5A at 250VAC. Power matrix modules are intended for switching heavy AC or DC loads or for slaving up to large external relays, contactors and solenoids. Used for applications requiring switching of either mains voltage or direct current. These modules are fitted with electro-mechanical power relays, gold-flash over silver alloy. A spare relay is built onto the circuit board to facilitate easy maintenance with minimum downtime.
-
Product
Drivers
-
Electro-Optical Products Corp.
EOPC offers a full line of drivers to electrically drive EOPC products. Drivers come as housed units powered from line voltage (110 VAC and/or 220 VAC) or as printed circuit boards.
-
Product
PXI 8x SPST High Voltage Reed Relays
40-310-001
-
The 40-310/320 range of high voltage switching modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
Mini UHF Connectors
-
Pasternack Mini UHF connector category has many part numbers, most of which are RoHS and REACH compliant. Mini UHF connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. These Mini-UHF connectors are built to precise RF and microwave industry specifications. Mini-UHF connector products are manufactured in male or female gender with 50 Ohm impedance. UHF mini connector products are available in straight or right angle versions, as well as, bulkhead, 4 hole panel or mountless options. These connector series in mini UHF designs include crimp/solder or solder attachment methods. Other mini-UHF connector options include Push-On or standard configurations. As with the other over 40,000 RF, microwave and millimeter wave Pasternack products, this mini UHF connector series is in-stock. Not only are these in stock, they will ship the same day as well.
-
Product
Actuation Methods for Functional Test Systems
-
Functional test typically applies full operational power to a final product or a loaded printed circuit board in order to determine if the Product/ PCB performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies within its Signature Series functional test fixtures.
-
Product
Riser
-
Designed to provide extra space in a SUMIT stack. They are printed circuit boards (PCBs) with SUMIT mounting holes and bus connectors.
-
Product
Ionic Contamination Test System
Omegameter SMD 650
-
The SCS Omegameter SMD 650, the long-time industry standard for ionic testing utilizing “static test” methodology, is designed to perform cleanliness testing on printed circuits and assemblies. Identifies the presence of ionic contamination on bare and assembled printed circuit boards and other electronic components. Provides an accurate and repeatable method for determining cleanliness on site. Provides immediate process control results, eliminating the need for outside laboratory testing.
-
Product
Precision Flying Probe Platforms For Automated Test Applications
-
Flying Probe technology is used to automate the testing of printed circuit boards (PCB) that would otherwise have to be tested manually. Adding a Huntron Access Prober to your test procedure will significantly decrease test times therefore increasing productivity.Access Probers can accurately place a probe on test points with high accuracy achieved using micro-stepping motors and linear laser encoders. Probing the smallest surface mounted devices is possible. Huntron Access Probers can automate your unique test process using the standard probe or by adding a custom probe of your design.Huntron offers three Flying Probe system configurations based on PCB size and test head requirements.
-
Product
NIM Mechanics
-
NIM cassettes with mounting blocks for printed circuit boards and optional NIM connectors.
-
Product
75 Ohm Mini SMB Connectors
-
75 Ohm Mini SMB connector category from Pasternack includes many part numbers, the majority are RoHS and REACH compliant. 75 Ohm Mini SMB connector series in this category will terminate to coax, PCB (printed circuit board) or terminal. Our 75 Ohm Mini SMB connectors are built to precise microwave and RF industry specifications. Pasternack 75 Ohm Mini SMB connectors are built in jack or plug gender with 75 Ohm impedance. Mini-SMB 75 Ohm connector items are available in straight or right angle versions, as well as, bulkhead, 2 hole panel or mountless options. These 75 Ohm Mini SMB connector designs include crimp/solder or solder attachment methods. We offer 75 Ohm Mini-SMB connectors with standard or high performance levels manufactured with brass or stainless steel bodies. As with our other over 40,000 RF, microwave and millimeter wave products from Pasternack, this 75 Ohm mini SMB connector series is in-stock. Not only are these mini-SMB 75 Ohm connectors in stock, they also ship the same day as they are purchased.
-
Product
PXI 24 Channel High Voltage Multiplexer
40-320-101
-
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
Digital I/O Card
PCI-DIO-120
-
The PCI-DIO-120, PCI-DIO-96 and PCI-DIO-72 are parallel digital input/output cards designed for use in PCI-Bus computers. The same printed circuit board is used for all three models and is populated for 120 bits, 96 bits and 72 bits respectively. The card is 12.2 inches (310 mm) long and may be installed in any 5-volt PCI slot in IBM and compatible computers.
