Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
Product
Solar Simulator for Concentrator Cells
-
Optosolar offers solar simulators with continuous light for small area solar cells (ca. 10mm x 10mm). depending on the cell size, the concentration ratio can exceed 1000 suns. Special designs cover low concentration on large area wafers (156mm x 156mm), as well as line focus applications (e.g. 8mm x 156mm at 8 suns). Flashlight Solar Simulators have the advantage of negligible temperature change to the solar cell. For this reason, they are often used for very high concentration ratios or for multijunction cells in a solar simulator with adjustable spectrum.
-
Product
Semiconductor Functional Verification Tools
Trek5
-
Breker’s solutions enable test reuse across simulation, emulation, prototyping and actual silicon, eliminating redundant effort across the development flow. The Breker “Trek” suite solves challenges across the functional verification process for large, complex semiconductors.
-
Product
Spectrum Analyzer
H45 Advance
-
The H45 are a milestone in the design of spectrum analyzers.Professional spectrum analyser - - 2,5GHz The latest technology and the latest features in a comprehensive range take will never become obsolete since any meter can be upgraded to the coming technologies .DVB, DVB-T,DVB-C, DVB-S,DVB-S2, LTE simulator
-
Product
Rainproof Tester
TF161
-
TESTEX Testing Equipment Systems Ltd.
Rainproof Tester, to determine the penetration resistance of fabrics or composites at different intensities of water impact. Simulated rain horizontally impacts fabric samples mounted vertically in a stainless steel bath. Samples are backed with a standardized blotting paper, which is weighed before and after each test. The rain is formed by a column of water, which can be adjusted from 600mm to 2400mm.
-
Product
ATCA 5U 14 Slot Mesh w uTCA connector for SHMM
1900001778-0000R
-
The 14-slot mesh backplanes have standard 1X full mesh topologies. Elma Electronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
PXI RTD Simulator Module, 4 Channel, PT1000
40-263-503
-
The 40-263-503 is a 4-channel PT1000 RTD Simulator. The 40-263 range is a cost effective method of simulating PT100, PT500 or PT1000 RTDs. It supports 4, 8, 12, 16, 20 or 24 channels in one or two PXI slots. Also, channels are able to be set as short or open circuit to simulate faulty wiring to a sensor.
-
Product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 32.7k Ohm
50-294-032
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
ATCA 5U 7 Slot replicated Mesh 40G
109ATCA507-3003R
-
The 5U 7 slot ATCA backplane is a replicated Mesh with dual shelf managers, designed to meet 40Gbps (4 x 10G ports) data rates. Elma's ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
Product
IMPULSE VOLTAGE GENERATOR
-
International Biological Laboratories
The impulse voltage generated in the electric power transmission and distribution system due to lightning or switching phenomena can be simulated by generation of impulse voltage of particular shape in the laboratory.
-
Product
PMC Intelligent Interface Card
IIB-1553-PMC
-
The IIB-1553-PMC is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the PCI Mezzanine standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card.
-
Product
Thermal Load Boards
-
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
Product
END-to-END VALIDATION TESTING
-
SANBlaze VirtuaLUN NVMe Initiator is the key piece of test equipment for anyone needing to test NVMe target devices. The VirtuaLUN feature set provides a unique set of functions applicable in all aspects of a product lifecycle; from development to design validation to test and QA. The ability to drive NVMe targets with a wide range of configurable attributes provides engineers with a flexible, scalable tool to simulate real disk and memory access environments and issues. Development, qualification and certification test cycles can be highly automated, reducing time and surfacing issues and errors.
-
Product
Power Temperature Cycling
-
Typically, this test would be selected when during its normal operating activity, the device is subjected to high temperature excursions and is required to power on and off at all temperatures. The power and temperature cycling test will determine the ability of a device to withstand exposure to such temperature extremes with operating biases periodically applied and removed. The worst case conditions expected in a typical; application will be simulated.
-
Product
Finite Element Analysis (FEA) Solution
Femap
-
Siemens Digital Industries Software
Femap is an advanced engineering simulation software program that creates finite element analysis models of complex engineering products and systems, and displays solution results. Femap can virtually model components, assemblies or systems and determine the behavioral response for a given operating environment.
-
Product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 1.81kΩ
50-297-022
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Component Test
-
Our innovative multi-function Electrical Component Testers have advanced functions such as voltage power control feed to activate components like radiator fan, headlights, horn, actuators, etc. and the sensor simulator can provide simulation of voltage signals, frequencies, square waves & duty signals with varying intensity to test the feasibility of good sensor signals in comparison to bad ones when troubleshooting vehicle electrical faults.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 26.7kΩ
50-297-032
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Non-Invasive Blood Pressure Simulator
SC-5 SimCube® NIBP
-
The STANDARD SC-5 SimCube® NIBP Simulator provides ECG, Respiration, Arrhythmia, Pacer Simulation, IBP and three Digital Manometer Modes of tests.
-
Product
Sand And Dust Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Sand and dust test chamber is also referred as dust-proof chamber, which is able to simulate the sand storm by putting the test piece in the chamber to judge the damage of sand-and-dust weather to products. Equipment is mainly applicable to determination of sealing performance of product shells based on the IPX5 and IPX6 degrees. Testing machine features a flow of air carrying dust in a vertical circulation, resulting in cycle use of sand during the test. Sand and dust testing has great significance to master the specimen’s performance to defend the penetration of dust particles, to withstand the abrasion of sands.
-
Product
DUST CHAMBERS
EDC Series
-
Free-flow dust circulation centrifugal blower.Uniform floating dust simulation across the test space.Dust pre-heating mechanism for free flow of the dust.Hopper re-vibration for free fall of settled dust.Blower speed regulation to ensure metered uniform dust floating inside the test space.Oil-free vacuum pump to simulate negative pressure for IP6X test.Volumetric air-flow meter/counter for IP6X test.View window with illumination.User-friendly Multi-function programmable timer.
-
Product
PXI Precision Resistor Module 3-Channel, 3 to 1.51M
40-297-150
-
This PXI Precision Resistor module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-113
-
The 40-297A-113 (PXI) and the 42-297A-113 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 238 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
Product
Cycle-ATV Dynamometers
EC997
-
The EC997 Series, our standard eddy current motorcycle chassis dynamometer, takes motorcycle performance tuning to the next level. The EC997 Series uses the industry’s most advanced electronics and Dynamic Load Control technology, featuring precision closed-loop torque feedback – a standard feature with every EC997 dyno. Competitor’s dynos on the market allow you to apply “percent % load” but Mustang has perfected the art and science of Dynamic Load Control and proudly offer the most sophisticated Dynamic Load Control dynamometer available at any price. Our superior control technology combined with our ultra-low inertia design allows you to precisely control loading to hold the engine at each RPM. Try doing that with a heavy drive roller and insufficient control technology – you simply cannot! Mustang has delivered thousands of performance dynamometer systems over the past 35 years and has perfected the art and science of dynamic vehicle loading and dynamometer control. We include each motorcycle make and model in our database including weight and drag coefficients so you can simulate the track right on the dyno! While other dyno manufactures are still trying to catch up with our technology, Mustang continues to lead the industry and is recognized around the world as the industry’s best with regards to dynamic dynamometer controls. Mustang has built racing dynos for Harley-Davidson as well as several end of production line testing cells for Harley-Davidson, Honda, and Polaris.
-
Product
Artificial Skies
-
As a simulator maker, we can say the artificial sky, among other devices, is the ideal instrument for every lighting designer and lighting engineer. In fact, to predict daylight penetration inside a building, a scaled model under an artificial sky is the only reliable prediction method in the case of unusual situations, complex geometries, or heavily obstructed windows.
-
Product
Solar Simulator
-
Jiangsu Keyland Laser Technology Co., Ltd.
Features:- Beyond Class AAA performance- Stable continuous working- 8000 data collecting points- Durable flash lamp- Voice prompt- Measuring data export- Customizable for special panels
-
Product
ARINC 429 Bus Interfaces
-
AIM’s > ARINC 429 test, simulation, monitoring and analysis modules use our field proven Common Core hardware design giving you the best performance, best feature set and highest functional integration on the market. The use of SoC (System on Chip) based core designs with multiple processors for real time bus protocol and application support, massive memory and IRIG-B time code encoder/decoder functions are standard. The latest versions also support avionics discrete I/O.
-
Product
Battery Testing
-
Weshine Electric Manufacturing Co., Ltd
The DC test method is adopted to simulate the actual use of the battery in a real and objective way, which can effectively eliminate the hidden dangers such as deficiency, deficiency and connection failure between batteries while measuring the internal resistance of the battery.
-
Product
4, 8 and 16 Channel ARINC429 Test and Simulation Module
ANET429-x
-
The ANET429-x is a member of AIM’s Ethernet based modules for analysing, simulating, monitoring and testing ARINC429 channels.
-
Product
Graphical Debugging for Verilog, VHDL, and C++ Simulators
BugHunter Pro
-
BugHunter uses the SynaptiCAD graphical environment and supports all major HDL simulators. It has the ability to launch the simulator, provide single step debugging, unit-level test bench generation, streaming of waveform data, project management, and a hierarchy tree. The unit-level test bench generation is unique in that it lets the user draw stimulus waveforms and then generates the stimulus model and wrapper code and launches the code. It is one of the fastest ways to test a model and make sure that everything is working correctly. The debugger also has exceptional support for VCD waveform files.
