Simulation
the approximation of actual operational conditions.
See Also: Simulators, Simulation Software, Simulation Testing, Modelling, Emulation
-
product
Lithium Battery Test Chambers
Dongguan Amade Instruments Technology Co., Ltd
Lithium battery test chambers are used to simulate various extreme conditions such as crush, impact, penetration, overcharge etc the lithium ion cells and batteries are subjected to during use, transportation, storage and disposal to determine the safety performances, tests including altitude simulation test, thermal test, vibration test, shock test, external short circuit test, impact/crush test, overcharge test, discharge test etc based on UN38.3, IEC62133, UL1642 standards. Applicable to communication products, computer products, consumer electronics, automobile power supplies and so on.
-
product
ATCA 5U 6 Slot Mesh
109ATCA506-300XR
The 5U 6-slot ATCA backplane is a 3X Replicated Mesh, compliant to the PICMG 3.0 Rev 3.0 specification. Elma Bustronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
ATCA 5U 14 Slot Mesh w uTCA connector for SHMM
1900001778-0000R
The 14-slot mesh backplanes have standard 1X full mesh topologies. Elma Electronic’s ATCA backplanes have been simulated and characterized by our signal integrity lab to optimize performance.
-
product
Basic Heating Module
Microwave heating analysis including loads rotation and translation, frequency tuning, heat flow and material parameters modification as a function of dissipated power. QW-BHM (Basic Heating Module) for QuickWave 3D provides a novel regime of operating the FDTD solver: the possibility of simulating microwave heating problems.The software has been prepared to work in sophisticated regimes, modelling rotation and movement of the heated load(s) even along complicated trajectories, etc. Transfer of the heat generated by electromagnetic fields can be modelled with external or internal Heat Transfer Module or by coupling QuickWave 3D simulations to external computational fluid dynamics packages.
-
product
Power Amplifier For Real-Time Dynamic Simulation(RTDS) Application
As the first power amplifier manufacturer in China, PONOVO has been offering various power amplifier products for customers in China and other countries since 2001. PONOVO has launched both conventional power amplifier for power system use and also 4-Quadrant power amplifier for more filed application, such as microgrid, windfarm, PV, HVDC, areospace, battery simulation, etc.
-
product
Finite Element Analysis (FEA) Solution
Femap
Siemens Digital Industries Software
Femap is an advanced engineering simulation software program that creates finite element analysis models of complex engineering products and systems, and displays solution results. Femap can virtually model components, assemblies or systems and determine the behavioral response for a given operating environment.
-
product
ARINC 429 Multichannel Interface Card for Mini PCI Systems
DAS-429mPCI/RTx
The DAS-429mPCI/RTx is an ARINC 429, multichannel interface card for Mini PCI systems. The card’s small size and suitability for Mini PCI notebook computers, make them a complete solution for developing and testing ARINC 429 interfaces and for performing system simulation of the ARINC-429 bus, both in the lab and in the field.The DAS-429mPCI/RTx is supplied with C drivers, including source code and Mystic application program.
-
product
Pulsed IV-Curve Solutions
Pulsed IV-Curve Test and Analysis System is our new development for 2015. It is an advanced and compact pulsed IV-curve characterization system designed to simulate pulsed ESD events such as TLP, vf-TLP, HMM, HBM, EFT, and LV-Surge. It will monitor the transient voltage and current waveform during the pulse in ps or ns segment, and test the pre- and post-pulse status (leakage current, breakdown voltage, biasing current, static IV curve, etc) of the device under test (DUT), such as protection devices, semiconductors, circuit modules, touch panel sensor, etc.
-
product
PXI Device Power Supply - 4 Isolated Channels, 20-bit Measurement Resolution
52310e series
Chroma 52310e Series i s a programmabl e PXI-Express DPS (Device Power Supply) Card designed for high-accuracy and reliable output power for device test applications. Its compact size, easy level of integration, and high flexibility make the 52310e Series ideal for multi-channel power supplies. Chroma 52310e Series features 8 selectable control bandwidths to ensure high speed output and stable operation; multiple current measurement ranges with a 20-bit DAC/ADC provide the highest resolution and accuracy with a sampling rate up to 600K S/sec; programmable internal series resistance for battery simulation. Chroma 52310e DPS series has a patented hardware sequence engine that has deterministic t iming to cont rol each DPS channel. The sequencer's on-board memory can store up to 1024 sequencer commands and 32k measurement samples per channel.
-
product
Dropout, Surge, Ripple Simulator and AC/DC Voltage Source
DSR 100 Series
DSR 100 Series systems provide complete, single-box solutions for immunity testing. They include a simple-to-use yet powerful standards waveform generator matched with an industry leading power supply technology and come with an extensive library of tests for many automotive and aviation standards.
-
product
PXI Analog Output
Our range of flexible PXI Analog Output modules features high accuracy & high resolution voltage and current sources that satisfy a wide variety of applications in Automated Test, including sensor and transducer simulation. Each product has a number of variants with differing channel counts to closely match a user’s specific requirements.
-
product
Plastics Simulation Software
Moldex3D
Moldex3D is the world leading CAE product for the plastics injection molding industry. With the best-in-class analysis technology, Moldex3D can help you simulate the widest application range of injection molding processes to optimize product design and manufacturability, shorten time-to-market, and maximize product ROI.
-
product
PXI 5A Fault Insertion Switch 20-Chan 2-Bus
40-198-002
The 40-198 is a 20 Channel Fault Insertion switch, primarily designed for the simulation of fault conditions in automotive/avionics applications involving the reliability testing of safety critical controllers.
-
product
Servo Tester
105
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
-
product
PXI/PXIe Battery Simulator Module, 2-Channel, Simplified Current Sink, 750 V Isolation
41-752A-903
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
product
Communication Data Logger
LE-270GR
LE-270GR is a Communication Data Logger, which has acceleration sensor and a connector for GPS antenna. It has logger mode with which you can records CAN/LIN communication logs in the SD/SDHC card for long hours and remote mode with which you can monitor data or GPS data on the PC at real time by connecting the analyzer with PC. It also has simulation mode with which you can repeatedly transmit CAN/LIN data which is registered in advance and selected on PC. It has galvanic-isolated two CAN transceivers and two LIN transceivers. Thus you can measure 2 channels of CAN/LIN communication lines and can simultaneously register GPS positioning data, acceleration data, and voltage data of 4 external signals.
-
product
Interface Module for the Multimode, Multiprotocol Excalibur 400 Family of Carrier Boards
M4K1553Px(S)
The M4K1553Px(S) interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing 1553 interfaces and performing system simulation of the MIL-STD-1553 bus. The module handles all standard variations of the MIL-STD-1553 protocol.Each M4K1553Px multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.Each M4K1553PxS single function (RT validated) module operates either as a Bus Controller, Remote Terminal, or Bus Monitor.
-
product
PCI Programmable Resistor Card 2-Channel 3 Ohm To 16.3k Ohm
50-294-031
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
AC and DC Electronic load
63800 series
The Chroma 63800 Loads can simulate load conditions under high crest factor and varying power factors with real time compensation even when the voltage waveform is distorted. This special feature provides real world simulation capability and prevents overstressing thereby giving reliable and unbiased test results. The 63800's state of the art design uses DSP technology to simulate non-linear rectified loads with its unique RLC operation mode. This mode improves stability by detecting the impedance of the UUT and dynamically adjusting the load's control bandwidth to ensure system stability. Comprehensive measurements allow users to monitor the output performance of the UUT. Additionally, voltage & current signals can be routed to an oscilloscope through analog outputs. The instrument's GPIB/RS232 interface options provide remote control & monitor for system integration. Built-in digital outputs may also be used to control external relays for short circuit (crowbar) testing.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-112
The 40-297A -112 (PXI) and the 42-297A-112 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 120 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Modular Breakout System 8-Pin Power D-type Plugin Module for 40-192
95-192-001
The 95-192-001 Plugin Breakout Module is designed to be fitted to a PXI 40-192 Fault Insertion Switch as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
product
Develop - Simulate - Validate JTAG / IJTAG based IP
NEBULA
You, your vendors and your customers being able to use one common interface to control and observe on-chip IP, resources and instruments. The figure below shows an example IC. The new IEEE 1149.1-2013 standard supports an init-data register for configuring the analog paramaters of I/O as well as controlling on-chip PLLs. The standard further extends this by defining in BSDL user test data registers or 'scan chains'. These registers enable the ability of generic software to control and observe mission mode IP and instruments simply by describing the register interface in BSDL.
-
product
PXI Precision Resistor Module 6-Channel, 3 to 11.4M
40-297-053
A simple solution for applications requiring accurate simulation of resistive sensors. The series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Panel-mounted HIL Power Amplifier
PAC60Ci
PAC60Ci is the six-phase real time simulation amplifier, with maximum RMS phase current of 30A and maximum output power of 450VA. This current amplifier is possessed of high accuracy and fast liner response.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 472Ω
50-298-120
The 50-298-120 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 472Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Medical Leakage Current Tester
2675Y
Shenzhen Chuangxin Instruments Co., Ltd.
The 2675Y Medical Leakage Current Tester Series Is The Test Equipment Used For Measuring Continuous Leakage Current And Patient Auxiliary Current Of Medical Electrical Equipment.It Designs And Products According To The GB9706.1_2020 (IEC60601-1:2012) .And The Test Circuit (MD)Input Impedance To Simulate The Body Impedance,It Accord With The Requirements Of GB9706.1-2020 (IEC60601-1:2012),The Test Current Can Run Up To 5A,And Provide Users With An Isolation Power Supply Which Adjustable Output Voltage For 0~250V Continuously Of The Basic Capacity Configuration For The 500VA And Provide Another 110% Voltage Source Of The Maximum Rated Voltage.It Can Satisfy The I,II, Various Types Of Equipment Test The Earth Leakage Current,Shell Leakage Current,Patient Leakage Current,Patient Auxiliary Leakage Current Under Normal Condition And The Single Fault.
-
product
Solar Simulators
TriSOL CPV
Concentrating Photovoltaics (CPV) has the promise of producing solar cells with high cell efficiencies, which result in a reduction in the cost of operating a PV module. However, a CPV system requires the integration of CPV solar cells, modules and CPV optics into one efficient system. OAI’s focus is CPV cell testing methodology. The CPV cells can now be tested using OAI’s advanced standalone CPV Simulators for low dose and high dose configurations. The low dose CPV Solar Simulator provides exposure up to 50 Suns, whereas, the high dose CPV Solar Simulator provides exposure up to 1500 Suns. The low and high dose simulators provide exposure in varying Sun concentrations in various beam sizes from 1.5cm x 1.5cm to 7.5cm x 7.5cm, and may be configured with OAI’s I-V Test Systems.
-
-
product
Programmable AC Power Source
Chroma Systems Solutions, Inc.
The Chroma programmable AC power source 61500/61600 series are the right solutions to meet complex single and three phase requirements due to their ability to simulate AC line conditions and measure critical product characteristics during testing. These features make the 61500/61600 series ideal for commercial, power electronics, avionics, military, and regulation test applications from bench-top R/D design verification and quality assurance to mass production.
-
product
Towing Dynamoters
From light passenger cars to heavy commercial truck vehicles, you can turn to us for a solution that saves you time and money by easily and reliably measuring attributes under a range of simulated load conditions, negative slopes and positive slopes up to 25% – all in a safe, controlled environment. Look to Taylor as the industry leader for a record of pioneering valuable towing dynamometer (dyno) advancements including:
