Kelvin Leads
A spring clip where the jaws are insulated from each other at the hinge point. 4-wire
-
Product
Kelvin IC Clip Lead
16089C
Accessory Kit
Measure odd-shaped components that you cannot measure using conventional fixtures
-
-
Product
Kelvin Contact Test
-
C.C.P. Contact Probes Co., LTD.
We offer different tip types for low resistance testing.
-
Product
Probes With Lead Wires
-
Used when the probe is installed some distance from the logger, controller, or other data acquisition device. Available in a variety of lead wire types with stripped leads or connectors attached.
-
Product
Test Leads and Probes
-
Test leads and probes are an intergral part of a complete measurement system and extend the capabilities of your digital multimeter.
-
Product
Test Leads
-
designed for electrical and electronics testing in today’s industrial environment.
-
Product
Thermocouple Extension Lead
EXT-6
-
The EXT-6 - 6 foot, Type T Thermocouple Extension Lead. Flexible vinyl covered.
-
Product
Kelvin Probe Set
11059A
Accessory Kit
Reduce ground-related errors and contact resistance through gold-plated flat tweezers and special gripping surfaces
-
Product
Ambient Single Point Kelvin Probe System
-
This single point Kelvin Probe System operates under ambient conditions and is small enough to be placed in a customized glowth box. The probe head operates with an oscillating membrane and can be easily exchanged. The preamplifier is integrated inside the probe head.
-
Product
Kelvin Clip
BU-78K
-
Kelvin Clip, Gold Plated Brass, 10 Amps, 2.3″ Length, 1/2″ Jaw Opening,
-
-
Product
MINIATURE SILICON DIODE TEMPERATURE SENSOR, 2 To 600 Degress Kelvin
-
Insight Product Company offers SILICON DIODE TEMPERATURE SENSORS CAN BE USED FOR TEMPERATURE Â MEASUREMENTS IN DIFFERENT FIELDS OF CRYOGENIC ENGINEERING AND EXPERIMENTAL PHYSICS. THEY ARE MINIATURE AND OPERATE IN THE TEMPERATURE RANGE FROM 2 TO 600 K.
-
-
Product
Off-Set Kelvin Test Sockets
-
This is an innovative and robust contact technology for making Kelvin contact to 0.5mm pitch QFNs. The contact uses a tip that is angled to one side, matched to an orientation that's flat on the tip. Two such contacts placed in opposition will touch the pad within 0.125mm. And because the tip is offset, the probe diameter is a robust 0.39mm and the load board pad pitch remains 0.5mm.
-
-
Product
Ultra-High Vacuum Kelvin Probe
-
Our Ultra-high Vacuum Kelvin Probes give the user full access to work function and contact potential difference (CPD) measurements under vacuum. Each system comes with a high-quality, manual, or motorized translator that enables reliable and accurate tip-to-sample positioning, and the unrivalled tracking system always holds the tip separation constant during the measurement. Even under vacuum, the work function resolution is 1 - 3 meV.
-
Product
Test Lead Set
34138A
-
The Keysight 34138A test lead set for digital multimeters contains fixed sheath banana plugs. The Keysight 34138A is compatible with the 34460A, 34461A, 34401A, 34405A, 34410A, 34411A, L4411A, and U2741A digital multimeters. 34138a is not compatible with 3458A instead use 34137A with 3458A.
-
Product
Calibration Lead Precision Resistor - Single
40-975-009-SL1
Calibration Lead Cable Assembly
The cable assembly is specifically designed to connect to the 9-Pin D-Type calibration port located on the front panel of Pickering Interfaces Module Part Numbers 40-260, 40-261, 40-262, 40-263 and 40-265.
-
-
Product
Precision Electronic Test Leads
34133A
-
The Keysight 34133A precision electronic test leads are designed specifically for working with small components and dense circuit boards. Each kit includes two test leads (one red and one black).
-
Product
PRO Test Lead Kit
142
-
#142 Pro Test Lead Kit includes our premium set of interchangeable specialty test probes designed for automotive use. This lead set features an extended length of 64 inches. The flexible back probing pins are great for sliding into automotive connectors like those on fuel injectors and MAP sensors. In addition, the large Crocodile Clips are good for clipping to grounds and battery terminals. Includes roll up storage pouch to keep your leads organized. These are compatible with most DMM’s and scopes.
-
Product
Leading Edge Sensors
-
The LaserGauge® Leading Edge Profiling System consists of a handheld or benchtop sensor and the Leading Edge software application. Designed to scan both sides of the blade simultaneously, the sensor returns a complete profile around the radius of the blade, which allows accurate measurements of the thickness and the plotting of the blade profile for comparison to its engineering design.
-
-
Product
Probes & Test Leads
-
The Di-LOG range to test leads are designed and manufactured to the highest quality and meet all safety standard as stipulated in BS EN 61010
-
Product
DMM MULTIMETER TEST LEADS
-
Flexible Vinyl Strain ReliefSoft Silicone Leads48" Length, 18 Gauge1000 Working Volts10 AMP RatedLow-resistance Gold ContactsRetractable Safety Shroud
-
-
-
Product
Extended Ethernet Flying Lead
E²FL
-
Due to vast geographies and complex field layout configurations, Subsea Ethernet transmission requirements may reach beyond the 100 meter maximum. Extended Ethernet Flying Leads (E²FL) enables Ethernet transmission beyond the limits of the previous 100 meter Ethernet assemblies.
-
Product
Kelvin Test Contactor
ecoAmp
-
ecoAmp™ Kelvin test contactor has a durable monolithic pin design with low and stable contact resistance. It is a high-power cantilever kelvin contactor with a patented spring and tip design for optimum heat dissipation. This ensures best reliability, long spring life and high yield even under highest current and temperature requirements. Featuring extended Automotive temperature range -60 ̊C to +175 ̊C, capable to stand thermal stress during high-power test. The contact motion is decoupled from the test board.
-
