Interface Adapters
Physical interface between interoperable elements.
See Also: Interfaces, Serial Interfaces, Parallel Interface, Bus Interfaces, UI, MIPI, Interface Test Adapters
-
product
Digital Interface Boards
Model 4863 OEM
* 114514 Board has same digital capability as the 4863 described above with GPIB IO.* GPIB interface header includes GPIB address switch input signals.* Use with any IC GPIB Connector/Address Switch Assembly.* Uses 9-32 Vdc power.* 114515 Board has same digital capability as the 4863 described above with GPIB and Serial IO.* GPIB interface header includes GPIB address switch input signals.* Serial interface header includes RS-232 and RS-485 signals. Use the 114597 Serial Cable Kit to connect the serial signals to your rear panel* Use with any IC GPIB Connector/Address Switch Assembly or with a 114597 Serial Connector Kit.* Uses 9-32 Vdc power.
-
product
8-Port RS232 Async Serial Communications Adapter PMC
2229
The Technobox 8-Port Async Communication adapter provides eight 16550-based UARTs using RS232 signaling levels. Each port provides the full set of data and modem control lines configured for DTE
-
product
PMC-to-4X PCI Express (PCI-e/PCIe) Adapter
6778
The Technobox, Inc. P/N 6778 is a PCI Express (PCIe/PCI-e) carrier that permits the insertion of a single PMC into a PCI-e slot (4X). The adapter orients the PMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket. Furthermore, the reverse orientation of the card permits direct access to the standard front I/O (if any) within the host chassis.
-
product
PXI Pull-Thru Adapter, PCB, QuadraPaddle, to 96 Pin SCSI Plug
510109485
PXI Pull-Thru Adapter, PCB, QuadraPaddle, to 96 Pin SCSI Plug
-
product
Interfaces
Channel link cable. Allows two scopes to be linked together to give 4 analog and 16 digital channels. Requires the four channel software to be installed.
-
product
Multichannel Memory-Mapped ARINC 708/453 Interface Card
EXC-708mPCIe
The EXC-708mPCIe is a multichannel, memory-mapped ARINC 708/453 interface card that supports two ARINC 708/453 channels, each programmable as transmit or receive. Each channel implements a 64K x 16 FIFO and supports polling and/or interrupt driven operation. The card complies with the PCI ExpressTM Mini Card standard. It’s small size and suitability for Mini Card compatible computers make it a complete solution for developing, testing, integrating 708 interfaces and for performing system simulation of the ARINC 708/453 Weather Radar Display databuses, both in the lab and in the field. In Transmit mode, each ARINC 708 word is written to the FIFO as a block of 100 16-bit words. In Receive mode, each ARINC 708 word is stored in the FIFO as a block of 103 16-bit words. The first two words comprise the 32-bit Time Tag, indicating the word’s time stamp. The next 100 words comprise the 1600 bits of the ARINC 708 word, which are followed by the Status Word.The EXC-708mPCIe card comes complete with C drivers including source code.
-
product
Quad Serial FPDP Interface with Virtex-6 FPGA - 3U VPX
Model 52611
- Complete serial FPDP solution- Fully compliant with VITA 17.1 specification- Fiber optic or copper serial interfaces- Up to 2 GB of DDR3 SDRAM- PCI Express interface up to x4- LVDS connections to the Virtex-6 FPGA for custom I/O- 3U VPX form factors provides a compact, rugged platform- Compatible with several VITA standards including: VITA-46, VITA-48 and VITA-65 (OpenVPX™ System Specification)- Ruggedized and conduction-cooled versions available
-
product
UXG X-Series Vector Adapter, Modified Version, 50 MHz To 20 GHz
N5192A
The N5192A is part of the UXG family of signal generation products designed for threat simulation; simulate complex signal environments for radar/EW.
-
product
Adapters
We have more than 1000 types of coaxial adapters on the shelf for immediate delivery; more than 200,000 coaxial adapters total. SMA, Standard N, SMP, TNC, BNC etc adapters are built to M39012, Mil-STD883 (Interface) & MIL-G-45204 or ASTM B488(plating). 2.4mm, 2.92mm, 1.85mm, 1.0mm, 7/16, 3.5mm, Precision N, Precision TNC, & 4.3/10 adapters are built to P287. 4,1/9.5 adapters are built to IEC standards. There are a few popular coaxial adapters for which we're not aware of a standard; u.fl etc. Mini DIN adapters are in stock.
-
product
32-bit / 33 MHz PMC to PCI Adapter
4933
This PMC to PCI Adapter product from Technobox permits delivery of PMC-derived applications in a standard PCI environment. Mechanically, a PMC card fits cleanly on a short-length PCI board, resulting in a highly acceptable delivery solution for desktop applications.
-
product
GPIB Parallel Interface
Model 4803
* 4803 Board provides 40 high-power TTL I/O lines that can sink 48 mA or source 24 mA. * Easily interfaces to TTL or CMOS signals and contact closures. * User can configure the data bytes as inputs or outputs.* Transfer data as bits, bytes as data strings or transparently.* Dual GPIB headers support connections to a GPIB Connector/Address Switch Assembly or to a GPIB Flat Ribbon Cable Assembly.* Optional Relay Driver board drives 24-40 relays.
-
product
PCB Adapter, Receiver, TriPaddle, 64 Position, To PCB-Mounted 2x34 Pin (BERG 65496-019) Connectors
510104128
The 64 Pin Signal Receiver Module is made from Ryton® R-7 and will withstand temperatures up to 220°C. The 64 Pin Signal ITA Module is made from engineered resin and will withstand temperatures up to 150°C. Both the ITA and Receiver Modules have molded nomenclature.
-
-
product
MiniPCI Express System Timer (PCIe Interface)
SKU-032-06
This MiniPCIe Timer uses a PCIe interface for synchronization of IP signals. This hardware-based solution provides accurate clock timing for Asterisk® open-source PBX software.
-
-
product
Manual Test Adapter With Rigid Needles
Frequently, manual test adapters are required for the functional and IC test. In order to contact the test subject, spring contact probes are often installed in the adapter, but the pitch of the spring contact probes is approx. 1.27 mm and thus too great for certain applications.
-
product
Shuttle Bus cPCI Intelligent Interface Card
IIB-SB-CPCI
The Shuttle Bus cPCI is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, and Multiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification 84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a cPCI platform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
product
DH Series QuickLink Adapter Kit with 3 x QL-SI Tips
DH-QL-3SI
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Coaxial Waveguide Adapter, APC-7, 12.4 to 18 GHz
P281C
The Keysight P281C adapter transforms waveguide transmission line into 50-ohm coaxial line. Power can transmitted in either direction, and each adapter covers the full frequency range of its waveguide band with SWR less than 1.3.
-
product
PCI Express System Timer (USB Interface)
SKU-032-01
The MiniPCI Express System Timer uses a standard USB interface to synchronize IP signals. This system timer provides accurate clock timing for Asterisk® open-source PBX software.
-
product
Power Supplies & Adapters
Curtiss-Wright Defense Solutions
Curtiss-Wright manufactures rugged DC/DC converter boards for stackable PC/104 and other small form factor embedded systems applications. Capable of supporting -40/+85°C extended temperature operation and high shock/vibration environments, these power supplies are routinely installed in vehicle and aircraft systems.
-
product
Adapter Plate, iCon, Receiver, to NI PXI-1042
310113530
Adapter Plate, iCon, Receiver, to NI PXI-1042.This adapter plate attaches directly to a NI PXI-1042 with portable monitor accessory (PMA-1115).
-
product
NI-5742, 16-Bit, 1 MS/s, 32-Channel Signal Generator Adapter Module for FlexRIO
782865-01
The NI‑5742 provides simultaneously sampled analog output channels for signal generation. It also features single-ended, DC-coupled inputs and general-purpose digital input and output lines for system stimulus and control. The NI‑5742 is ideal for applications requiring high-channel density and the power of a user-programmable FPGA. Each channel has a user-configurable sample rate, and data is written directly from the FPGA. To use the NI‑5742, you must pair it with a compatible PXI FPGA Module for FlexRIO.
-
product
Ethernet To GPIB Instrument Interfaces
ICS's 9055 and 8055 Ethernet to GPIB Instrument Interfaces convert any GPIB instrument into a VXI-11.3 compatible instrument that does not require special drivers and is compatible with the following operating systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows systems with VISA or an RPC library. ICS's 9055 and 8055 use VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. To learn more about the VXI-11 protocol and how it benefits your system, download our new VXI-11 Tutorial or a copy of the VXI-11 Specification.
-
product
NI-9866, 1-Port C Series LIN Interface Module
781963-01
1-Port C Series LIN Interface Module—The NI‑9866 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The NI‑9866 excels in applications requiring real-time, high-speed manipulation of hundreds of LIN frames and signals such as hardware‑in‑the‑loop (HIL) simulation, rapid control prototyping, bus monitoring, automation control, and more. You can perform this manipulation while taking other DAQ measurements in the same CompactDAQ hardware platform or while performing low-level FPGA control and embedded monitoring in the same CompactRIO Chassis.
-
product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-01
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
product
FlexRIO Adapter Module Development Kit for Modular I/O
780711-01
FlexRIO Adapter Module Development Kit for FlexRIO—The FlexRIO Adapter Module Development Kit (MDK) for Modular I/O enables you to choose the specific converters, buffers, connectors, and other components so that you can build the exact analog and digital I/O you need into a custom adapter module for FlexRIO. NI recommends that you have custom printed circuit board (PCB) design and hardware description language (HDL) code development experience to use the FlexRIO Adapter MDK for Modular I/O.
-
product
Portable Interface Unit
1553-USB-PIU
The 1553-USB-PIU is a Portable Interface Unit providing full MIL-STD-1553 test, simulation and bus analysis capability in a compact self-contained unit, to connect via a USB interface to suitable host systems. The unit provides support for all 1553A, 1553B, McAir and STANAG 3838 variants in a self contained battery operated unit, and is supplied with a matching power supply and battery charger unit for desk-top use. The 1553-USB-PIU supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a variable amplitude dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The unit is supplied with "C" Driver library, together with a Windows GUI, providing a user friendly software tool for all 1553 set-ups, data management and storage.
-
product
High Speed Load Cell Test Interface
LCIC-4CH
Industrial Measurement Systems Ltd.
The latest stand-alone controller model: LCIC-4CH, was specially designed to fit portable wheel and axle scales for determining the weight of trucks or heavy vehicles either in static mode or in motion, with very high accuracy and very friendly to operate. The In-motion speeds up the weighing process and allows weighing a truck without the need to stop.In the last 16 years, our stand-alone High-Speed weighing-in-motion controller model: LCIC-WIM was sold all around the world and as for today, thousands are being in use when among our customers are some well known weighing manufacturers.Most of our customers around the world are scale manufacturers or integrators that were able to offer the market the most advanced WIM scale with very short time to market and minimum R&D expenses.
-
product
PCI to PCI Express Adapter
SKU-011-01
The PCI to PCI Express Adapter simply turns your computer’s existing PCI slot into a PCI Express slot. This provides a seamless interface for older PCI systems to accept new PCI Express devices – making it possible to utilize old test equipment (computers, PCI extenders, PCI bus analyzers etc.) during migration from PCI to the PCI Express interface.There is no need to purchase additional software or to install new device drivers; simply plug & play!
