Filter Results By:
Products
Applications
Manufacturers
-
product
ARINC 818 Recorder
ARINC 818 Digital Video Recorder powered by Xilinx Zynq Ultrascale+ MPSoC device, is a multi-channel record/playback system that accepts any form of ARINC 818 video input with different resolution & refresh rates. The received ARINC 818 video stream is encoded with the assist of an on-chip H.264/H.265 video codec engine which is capable of performing simultaneous compression and decompression of video streams. Finally, the encoded video is stored in SSD hard drive.
-
product
ARINC 818 Switch IP Core
ARINC 818-2 is a point-to-point, serial protocol, high bandwidth, low latency protocol for the transmission of uncompressed video, audio, and data during blanking period, widely used in AVIONICS application. Since a vast portion of the newer applications of the ARINC 818-2 have several displays with many channels of ARINC 818-2, switching has turned out to be more imperative. ARINC 818-2 switch can support up to 12 channels. Multiple switching modes such as broadcast, unicast, multicast, and mixed are also supported.
-
product
ARINC 818 Analyser
iWave’s ARINC 818 Video Protocol Analyzer (VPA) instantly verifies the ADVB Packets against ARINC818 Standards. ARINC818 VPA software efficiently captures, decodes the ADVB data, and displays the ADVB data, raw video data, and error status. It is an excellent troubleshooting tool that helps to quickly detect and rectify errors in the ARINC 818-2 applications, simultaneously ensuring compliance of the system with the ARINC 818-2 standards.
-
product
ARINC 818-2 IP Core
iWave’s ARINC IP core is ARINC 818–2 compliant offering point-to-point, high-speed, low latency video transmission. This IP core can be implemented on any transceiver-based FPGA device. It can be used for both transmit and receive applications. This core supports configurable ADVB video formats and uses a simple streaming interface to interface with video & image processing IP cores supported by FPGA vendors.
-
product
ARINC 818-3 IP Core
The ARINC 818-3 IP core offers higher data rates and encoding for high-resolution real-time avionics video. ARINC818-3 standard provides 64B/66B schemes to support high-speed ARINC applications having data rates up to 28Gbps. Display emulation for testing, low latency guidelines, and fixing typographic errors to previous versions was new in this specification.
-
product
ARINC 818 to HDMI Converter
The ARINC 818 to HDMI converter is a rugged standalone module available in half-length PCIe form factor used for ARINC 818 to HDMI conversion, HDMI to ARINC 818 conversion, 2x ARINC 818 Switch as well as ARINC 818 Duplicator/Splitter. It is a video Converter module designed with Kintex-7 FPGA, using an Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
product
ARINC 818 Monitor
ARINC 818 Monitor is a rugged display module, powered by High-Performance FPGA to accept various ARINC 818 line rates up to FC 4x and display the converted video data on the monitor of various ICD Specification with very low latency. It supports any progressive video up to Full HD @60fps. These monitors empower pilots to organize and visualize the key information they need.
-
product
ARINC 818 Tester
iWave 3U VPX High-Speed Video/Data Processing Card is a rugged standalone module in the 3U VPX form factor, aimed for the high-speed data, video processing, and display applications is ideal for military, defense, and aerospace applications requiring an optimal balance of performance and power efficiency. iWave 3U VPX High-Speed Video/Data Processing Card is implemented using Xilinx Kintex-7 device architecture and has I/O interfaces including High speed 16 channels of transceiver interfaces capable of operating up to 6 Gbps data rate, Gigabit Ethernet, RS232, RS422, PCIe interface, Built-in health monitoring circuits, HDMI input, and output interfaces
-
product
HOTLink module (SAM)
ARINC 818
The HOTLinkTM stand alone module (SAM) is an invaluable tool for HOTLink testing. The SAM can be used as a portable signal converter, splitter, test pattern generator, or continuity tester. The SAM comes standard with an A/C adaptor and is also compatible with A/C 28 VDC.
-
product
Video and Protocol Analyzer
The Video and Protocol Analyzer (VPA) verifies compliance of designs against the ARINC 818 standard. The VPA software and interface accurately and efficiently decode and display data and flag errors. Multi Stream is a new standard feature of the VPA, empowering it to tackle ARINC 818 interfaces with multiple embedded streams of high-speed video.
-
product
ARINC 818 to DVI Converter
The ARINC 818 to DVI converter is a rugged standalone module available in 6U cPCI form factor used for ARINC 818 to DVI conversion, DVI to ARINC818 conversion, ARINC 818 Mux as well as ARINC 818 Duplicator either on front panel or via cPCI back panel. It is a video Converter module designed with Cyclone V GT FPGA, using Analog device Video Encoder, and Decoder to provide video interfacing requirements.
-
product
Digital ARINC
TA903-02
This panel mounted or portable display that reads ARINC 568 distance or ARINC 561 LRN distance. This display employs smart label detection circuitry so that received data must agree with unit strapping. This display is ideal for monitoring distance generated from a GPS, FMS or Dme or a system interface adapter.
-
product
PMC ARINC 717 Board
MS 1721
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- Spartan-3AN FPGA with ARINC 717 IP Core- One Channel ARINC 717 Transmitter and Receiver- Generates all PCM telemetry signals like NRZ, Bi-Phase, - Differential Bi-phase, DM signals- Used to test all types of PCM based telemetry equipments- Configurable output signals format (parity, word length, Minor, Major frame, Bit position)- User can configure the words and word positions in the frame- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
product
ARINC Protocols
Abaco's ARINC solutions provide feature-rich functionality and a high degree of flexibility combined with a user-friendly design and graphical application support.
-
product
12 Channels, ARINC 429/575 Communications
AR1
The AR1 provides an ARINC 429/575 communications interface with 12 channels. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer. Each channel is programmable as either Tx or Rx.
-
product
ARINC 429 Test & Simulation Instrument for VXI
VXI-429
Avionics Interface Technologies
Programmable High/Low Speed Operation Concurrent operation of all Tx/Rx Channels at high data rates
-
product
ARINC Interface Cards
- Wide Selection of COTS ARINC Interface Cards/Boards and Real-Time Appliances- 4-48 Shared and Dedicated, Independent RX/TX Channels- Portable FPGA AltaCore Design – Reduced Parts Obsolescence Risk- Most Advanced Error Detection and Injection Available- Parametrics Variable Voltage on ENET-A429P
-
product
3U cPCI 8 Channel ARINC 429 Module
DP-cPCI-4296
DP-cPCI-4296 board features cPCI based eight channels ARINC429 protocol interface. As part of the cPCI family, the DP-cPCI-4296 board is fully compliant with compactPCI® specification 2.0 R3.0. and CompactPCI® Hot Swap Specification 2.1 R1.0.
-
product
ARINC 429 Test And Simulation PCIe Module
PCIe-C429
*4, 8, 16 or 32 software programmable TX / RX channels*X4 lane PCI Express host interface*Programmable high / low speed operation*Simultaneous operation of all TX / RX channels*Error entry and detection*128 MB RAM*Label selective triggering for recording / filtering*Sorting according to SDI field*IRIG-B timecode encoder / decoder for data correlation*Real-time recording and later analysis of multiple channels*Supports: C, C ++, C # and .net*Driver support: Windows, Linux, VxWorks and other systems
-
product
ARINC 664 Simulator & Analyzer Applications Software
F-SIM-A664
Avionics Interface Technologies
Software GUI Application for Operating AIT ARINC 664 Interfaces - Simulate Multiple ARINC 664 End Systems Simultaneously - Full definition of input/output VLs, input/output Sampling and Queuing message ports, & TFTP Clients & Servers - Capture & Analyze Data from Multiple Virtual Links (VLs) - Live display showing all of the detected ARINC 664 VLs and message counts - Live displays showing all of the detected source and destination message (UDP) ports - Record network data to PCAPNG for use with Wireshark - Replay Previously Captured Bus Data - Also Supports MIL-STD-1553, ARINC 429 & Data Load operations
-
product
AFDX ® / ARINC 664 Test And Simulation PXI Module
PXI-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Stard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applicationsWindows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
ARINC 429 Test & Simulation Interface for VME
VME-429
Avionics Interface Technologies
4, 8, 16, 32, or 64 Software Programmable Tx/Rx Channels - Programmable High/Low Speed Operation - Concurrent operation of all Tx/Rx Channels at high data rates - Full Error Injection & Detection - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B Time Code Encoder/Decoder for Data Correlation - ANSI Application interface supporting C, C++, C#, and .net development - Device driver support: Windows, Linux, & VxWorks (others on request) - Designed for extended temperature operations - 64-bit VME - Interface (VME master & slave capability) - Front Panel and Rear I/O (P2) Available
-
product
Digital & ARINC Standards Display Panel
TA-3001
This is our soon to be introduced Digital Standards Panel. (2ND QTR) This panel is available with or without a Precision Resolver drive. Included on the panel are four digital displays; TA-902 API, TA903-01 OBI, TA903-02 Distance and a TA903-03 serial distance display. This panel when paired with the TA-3000 GPS/FMS test panel will make one of the most capable testing solutions available today
-
product
AFDX® / ARINC 664 Test And Simulation PCIe Module
PCIe-C664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous with ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Advanced MIL-STD-1553 & ARINC LabVIEW Software
AltaAPI-LV
Most of Alta’s MIL-STD-1553 & ARINC products include the industry’s most advanced National Instruments’ LabVIEW™ & RT Support Tools, AltaAPI-LV. Built-in native NI LabWindows™ environment and PCI VISA drivers, Alta’s AltaAPI-LV provides a unified NI tool for easy integration to LabVIEW, RT, and LabWindows™ applications. Easily port native DLLs for Testbench or VIs for Veristand.
-
product
PMC ARINC 429 Board
MS 1723
- Bus Interface:- 32 Bit PCI Bus with PMC Interface- Speed of operation up to 66MHz- Spartan-3AN FPGA and Arinc429 controller based design- 8 transmit and 8 receive independent channels- Driver interface for Windows2000/XP/VISTA and LINUX OS- Self Test future
-
product
ARINC 615A Data Loader Software Kit
F-SIM-LDR-615A
Avionics Interface Technologies
The F-SIM-LDR-615A software application is an ARINC 615A data loader tool which is compatible with AIT’s family of ARINC 664 interface modules and standard LAN interfaces available on most PC’s. The F-SIM-LDR-615A application supports ARINC 615A load operations over Ethernet and ARINC 664 networks.
-
product
AFDX ® / ARINC 664 Test And Simulation XMC Module
XMC-664
*Supports IEEE 802.3 10/100/1000 Mbit / s full duplex Ethernet connections*Uses SFPs to support both electrical and optical interfaces*Half-size PCI / PCI-X modules*Simulates multiple AFDX® / ARINC 664 end systems*Standard Ethernet processes simultaneous to AFDX® / ARINC 664*Up to 128 output VLs and 512 input VLs*Upper layer protocol handling (ARINC 653, UDP, IP) managed onboard*DMA for high data rate applications*Windows XP / 7, Linux, and LabVIEW Real Time Drivers & APIs (others on request)*Easy to use tool for configuring AFDX® / ARINC 664 end systems (XML based)
-
product
Intelligent ARINC Interface Module
M4K717
The M4K717 is an intelligent ARINC 717 interface module for the multiprotocol Excalibur 4000 family of carrier boards.The module supports two ARINC 717 receive channels and two transmit channels.In transmit mode, the module sends the four subframes from a pre-defined buffer in dual-port RAM.In receive mode, the module stores all subframes with status and Time Tag information appended to each subframe.The M4K717 comes complete with C-driver software library including the source code.
-
product
ARINC 429 Test & Simulation Interface for PCI Express
PCIe-C429X
Avionics Interface Technologies
16, 32, or 64 ARINC 429 Channels (up to 32 Tx & 32 Rx) - Programmable Tx channel output amplitude - Programmable High/Low Speed Operation - Eight (8) Discrete I/O (Four (4) inputs, and four (4) outputs) - Concurrent operation of all Tx/Rx Channels at high data rates - Full error injection and detection - Data capture filtering, 100% bus recording, and physical bus replay - Rate-oriented Label Transmission - Label Selective Trigger for Capture/Filtering - IRIG-B time code encoder/decoder with free-wheeling mode - Application Interface supporting C/C++, C# and VB.NET Development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
