Filter Results By:
Products
Applications
Manufacturers
IRIG
Inter-range instrumentation group time codes.
-
product
MIL-STD-1553 IRIG 106 Chapter 10 Streaming Application
F-SIM-1553-CH10-STREAM
Avionics Interface Technologies
Streams MIL-STD-1553 Data from AIT MIL-STD-1553 interfaces in Chapter 10 Format - Software application which is Compatible with all AIT MIL-STD-1553 Interfaces - Capable of streaming data captured from one or multiple MIL-STD-1553 Bus Interfaces - Streamed data can be sent to a single network system or multicast on the Ethernet LAN - Compatible with AIT F-SIM-1553-AVOE analyzer or 3rd party Chapter 10 systems - Timestamps & Errors detected embedded in Chapter 10 stream
-
product
8" Cable
CONW1553-1
Transitions from a card end connector (with IRIG) on the QVME-1553 or QVXI-1553X into two 8" cables with CJ70 Twinax, 3 lug, 1553 cable jack ends, and four 8" cables with BNC cable jacks for I/O triggers and IRIG Rec/Gen.
-
product
IRIG Time Code Receiver & Generator for Computers (PCI Express)
TCR180PEX
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. The output format is independent from the incoming IRIG signal - a perfect solution to your IRIG conversion requirements. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device.
-
product
IRIG Time Code Receiver for Computers (PCI Express)
TCR180PEX-EL
Meinberg Funkuhren GmbH & Co. KG
The TCR180PEX-EL receives IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes and can be used for synchronizing the system time of its host PC. The IRIG output of this card can generate an IRIG signal for other IRIG time code readers. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements).
-
product
Countdown Or Countup Clock Controller
RC600
The RC600 is a remote control that adds both countdown and countup timer control features to our NTDS and TCDS clocks. Reference or generate time input from NTP or time code (IRIG & SMPTE). Control a virtually unlimited number of time code clocks and network clocks.
-
product
Dynamic Data Simulator
LS-70-S
The Lumistar LS-70-S PCI Dynamic Data Simulator allows complex data streams to be generated for evaluation of bit synchronizers and PCM decommutator performance. It can also be used for uplink command generation to vehicles in flight, checkout of complete telemetry links, and playback of archived hard drive data in any format with the appropriate dll. The PCI board is only 7 inches long and contains the dynamic simulator and IRIG Time Code Generator.
-
product
Time Measurement Equipment
TimeSpy
The TimeSpy precisely measures the time accuracy of a wide range of inputs (such as: NTP, IRIG B, 1PPS, and ASCII) against an internal precision GPS-controlled oscillator, displayed on the large, full color windows-based touch screen. The TimeSpy can precisely measure the time error at the point of use for systems where time is distributed over large distances. The TimeSpy can also measure free-running clocks and timing systems which are synchronized from untraceable sources, such as television and radio broadcasts, electrical power lines and the internet.
-
product
IRIG B to NTP/SNTP Converter
Signals & Systems India Private Limited
IRIG B TO NTP/SNTP CONVERTER – SPC-INS-1010 is a compact DIN rail mountable protocol converter unit which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using IRIG-B signal obtained from GPS receiver. It provides nanosecond accuracy when external time references are not available. It has the storage facility to store the system log file. It delivers NTP, SNTP, PFC-Pulse, RS232 & RS485 outputs. The system enables configuration and monitoring through Web-based application. It supports a wide range of power supply input either 90V-260V AC/DC or 18-36VDC or 36V-72VDC.
-
product
PCI Express Timecode and GPS Reader Generator
PCIEX-SyncClock
The PCI-Express time code reference timing card with standard options such as IRIG B and optional GPS receiver provides an extremely accurate time source to the PCI-Express bus.
-
product
Bus Level Timing Cards
Brandywine offers the widest range of timing plug-in card form factors in the industry from the PCI timing cards to PMC to VME cards. With the largest variety of options including standards like IRIG B, 1PPS, Have Quick, and GPS you can customize your timing card to fit your needs. All of Brandywine's board level timing cards are made in our factory in El Paso, Texas which ensures quick delivery and quantity ranges from small to large for a low price.
-
product
Intelligent, Single- or Dual-Channel MIL-STD-1760 Adapter
EXC-1553UNET/Px-1760
The EXC-1553UNET/Px-1760 is an intelligent, single- or dual-channel, MIL-STD-1760 adapter. Its small size and ability to interface through USB or Ethernet interfaces make it a complete solution for developing, testing and performing system simulation of the MIL-STD-1760 bus, both in the lab and in the field.The EXC-1553UNET/Px-1760 shares its API with the entire Px family so that applications currently running on PCI, PCIe, ExCARD or PCMCIA boards will run without change on this device.Multiple units can operate via USB ports on the same computer. In addition, multiple units can operate on the same network, by programming each one with a unique IP address, and can be accessed from any computer on the network.In addition the EXC-1553UNET/Px(S)-1760 provides 8 I/O Discrete signals and an IRIG B input.
-
product
High-Power Flight Termination Systems
Kratos Defense & Security Solutions, Inc.
The Kratos Flight Termination System (FTS) is a turnkey system capable of transmitting MONITOR, ARM, and TERMINATE flight termination encoded command signals, as well as 20 individual IRIG tones (up to 6 simultaneously).
-
product
PCI Express Timecode and GPS Reader Generator
PCIe-SyncClock LP
The PCI-Express SyncClock LP from Brandywine Communications provides precision time with zero latency to the host computer over the PCI bus. An on-board microprocessor automaticallysynchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, GPS or HaveQuick. The clock can free run and be set by commands from the host over the PCI Express bus.
-
product
Multi Protocol Boards
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
product
Mini PCI Express Timecode and GPS Reader Generator
SyncClock
The Mini PCIe SyncClock32 from Brandywine Communications provides precision time with zero latency to the host computer using one Mini-PCIe slot. An on-board microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, HaveQuick.
-
product
Time & Frequency Distribution Amplifiers
Brandywine offers a wide range of high quality, state of the art signal timing distribution amplifiers, all with very low phase noise. These precision timing signal distribution amplifiers offer a variety of time and frequency signals and interface formats including IRIG A, IRIG B, Have Quick, 1PPS, as well as low phase noise reference frequencies. All of our distribution amplifiers feature dual inputs with automatic failover and multiple independently buffered outputs.
-
product
Aerospace Interfaces
Aerospace InterfacesDecode and visualize data from ARINC 429, MIL-STD-1553, IRIG CHAPTER 10, iNET and IRIG Chapter 4 PCM telemetry data interfaces.
-
product
GPS synchronized NTP Server
NTV-100
Brandywine Communications NTV-100RG is an affordable, convenient and flexible NTP Server. This network time server accurately time synchronizes computers, time displays, PBX’s, and a wide variety of other equipment. The NTV-100RG is a small, rack mounted NTP Server that can synchronize to GPS or to the IRIG B time code to provide NTP time.
-
product
Aerospace Testing Solutions
Aerospace Testing SolutionsDewesoft offers a variety of solutions for aerospace testing. From standard data recording, structural dynamics, rotating machinery analysis, acoustic testing, to more specific applications like ground station telemetry solutions with full support for ARINC-429 and MIL-STD-1553 buses, PCM telemetry, IRIG 106 - Chapter 10, Ethernet packets, and iNet telemetry.We can provide flexible and robust data acquisition hardware and software that will match your requirement for testing airplanes, helicopters, rockets, satellites in the air, space, or on the ground - proving ground, wind tunnel, vibration shaker or acoustic chamber. Our solutions are being used and trusted by leading aerospace companies on the most demanding projects like NASA, ESA, Space X, Airbus, Boeing, Lockheed Martin, Bombardier, Honeywell to name just a few.
-
product
IDM+
Multi-functional fault recorder including: -- Disturbance fault record (DFR)- Dynamic disturbance recording (DDR) - Phasor measurement unit (PMU C37-118)- Power Quality (PQ Class A)- Travelling wave fault location (TWS to +/-60m) - Impedance fault location- Protocols (61850, Modbus, DNP3) - Sequence of event recording (SOE)- GPS, IRIG and NTP time sync- iQ+ masterstation software.
-
product
IRIG Time Code Receiver & Generator Module
TCR180
Meinberg Funkuhren GmbH & Co. KG
The module TCR180 has been designed to receive and to generate IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device. The frequency locking of the master oscillator to the time code system enables this module to generate fixed and programmable standard frequencies with high accuracy and stability. Various oscillator options allow the cost efficient implementation of different requirements concerning the accurracy of the outputs. The generator of the IMS-TCR module generates pulses per second and per minute and per hour. Four programmable outputs are also available. The pulses are synchronized to UTC-second.
-
product
Tone Receiver/Decoder
Kratos Defense & Security Solutions, Inc.
The Tone Receiver/Decoder is a rack-mount receiver that will display the presence of any of the 20 IRIG standard tones, transmitted either individually or in combination as command tones (e.g. Monitor, Arm, Destruct, etc.). It accepts a universal AC power input, and it can be tuned in 100kHz steps for carrier signals in the range of 406MHz – 450MHz compliant to RCC 313 and 319 for compliant IRIG tones.
-
product
IRIG Timecode Receiver and Generator
RG1
The RG1 Time Code receiver synchronizes to IRIG-A/B/G time codes and provides precise time in a memory register, for the host SBC.The IRIG output of the card can be used to synchronize other IRIG time code readers. Additionally, the RG1 includes a real-time clock (RTC) that may be used as a reference source for IRIG master applications, to free the system processor from the task of updating the master timer.
-
product
Receivers
Designed to demodulate IRIG destruct tones, this receiver uses an up-converting superheterodyne configuration for high dynamic range and image rejection and has a receive sensitivity of better than -107 dBm. Originally developed to monitor/verify Range Safety Command Destruct Transmitters, it is a compact rugged design usable wherever a high tolerance to shock, vibration and temperature is required.
-
product
GPS Master Clock
Signals & Systems India Private Limited
GPS Master Clock System – MCS-GPSMC-1010 is a 3U Card rack type, 19” Rack-mountable Redundant GPS Time Server which synchronizes and maintains the timing and frequency requirement of power and process industry equipment using a signal obtained from any one of the sources like GPS or GLONASS or Time protocols such as NTP and IRIG. It distributing the same time signal through several types of interfaces. It provides redundancy for Power and GPS receiver to increase reliability and offers protection against time synchronization failure. The system is field-upgradeable and an extremely flexible system, designed to handle time synchronization requirements today and in the future. It provides nanosecond accuracy when external time references are not available. It has a storage facility to store the system log file. It delivers NTP, SNTP, IRIG-B, PFC-Pulse, DCF77, BCD parallel data, Ethernet Fiber Optic & RS485/RS232 outputs. System enables configuration and monitoring through Web-based application. It supports a wide range of power supply either 90V-260V AC/DC or 18-36VDC or 36V-72VDC. Power supply model can be mixed and matched as required by the user, depending upon power supply options available at the installation site.
-
product
CPCI timing plug-in
CPCI-SyncClock32
The CPCI-SyncClock32 from Brandywine Communications provides precision time with zero latency to the host computer over the CPCI bus in the 3u form factor. An on-board microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, GPS or Have Quick.
-
product
Automated Telemetry Test Station
ATTS5000
Systems Engineering & Management Company
The ATTS 5000 was developed by SEMCO to ensure that receiver systems successfully perform at both IRIG 118 Chapter 4 recommended tests, as well as additional customer-specified performance parameters. The ATTS 5000 ensures that the highest quality test data is consistently and repetitively collected on each and every system.
-
product
Advanced PC/104 Timing Board
PC104-Plus SyncClock32
The PC/104Plus SG from Brandywine Communications provides precision time with zero latency to the host computer over the PCI bus. An on-board microprocessor automatically synchronizes the clock to reference signal inputs. The reference signal inputs can be 1 PPS, IRIG or NASA time codes and optionally, GPS or HaveQuick.
-
product
IRIG B Booster
Signals & Systems India Private Limited
IRIG B Booster – SIB-1010 is used to boost the IRIG-B AM and PWM/TTL signal which is received from the GPS unit. It provides easy and affordable connectivity to substation equipment and power generation and distribution equipment. With this Plug-N-Play unit, you can expand your IRIG B connections to multiple devices instantly. It is rugged and surge-protected equipment. Its cabinet can be mounted directly on a wall, panel or DIN Rail, without the need for additional brackets. It has an inbuilt power supply module, therefore, doing away the need for an external power adapter.
-
product
Command Encoder/Exciter
Kratos Defense & Security Solutions, Inc.
The Command Encoder/Exciter (CEE) is a rack-mount unit ideal for test and verification of Flight Termination Receivers (FTR) and/or Tone Receiver/Decoders. It accepts a universal AC power input, and it generates a modulated RF output carrier signal adjustable in 100kHz steps from 406MHz – 450MHz from suitable for interrogation all RCC 319 compliant IRIG FTRs.
