Filter Results By:
Products
Applications
Manufacturers
Optical Combs
Frequency comb measuring light frequencies.
-
product
Optical Frequency Combs
The Optical Frequency Comb technology is regarded as a breakthrough technology for measurements with highest accuracy. Lowest phase noise, stable supercontinuum, and turn-key operation make the Menlo Optical Frequency Comb solutions unique in accuracy and reliability. According to our principles: The best Optical Frequency Comb for any application.
-
product
Add-ons For Metrology
We offer add-on products for Optical Frequency Combs and metrology applications. These include heterodyne photodetectors (BDU), and highly stable RF oscillators, just to name a few.
-
product
Quantum Laser Systems
By combining the Optical Frequency Comb and multiple ultrastable frequency stabilized lasers in a transportable, rack based system Menlo Systems offers a complete laser system for most demanding applications like optical clocks, quantum computing, and quantum physics experiments based on cold atoms, molecules and ions. The customer can configure the system in terms of laser wavelengths, laser power and frequency accuracy so that it is optimally matched to the application.
-
product
Automated Optical Switch - PXI
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
PXI Optical Switch
The PXI Optical Switch is available in many different switching configurations for customized optical switching. It offers both single-mode and multimode fiber options that can support switching of very small wavelength signals. The switch provides either SC/PC, FC/PC, SC/APC, or FC/APC fiber-optic connectors. You can use the PXI Optical Switch for repeatable, low-loss switching.
-
product
Optical Switches
Fast and reliable optical switches to streamline your test procedures. Can be customized with a wide range of switch configurations, fiber types and connectors.
-
product
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch
786598-01
PXIe, 1-Channel, SMF28 Fiber, 1x4 PXI Optical Switch - The CohSol SwitchPXIe-1003-1 is a PXI Express, 1x4 multiplexing switching module that supports optical switching at wavelengths from 1,260 nm to 1,630 nm using single-mode fiber. The switch provides either SC/PC, FC/PC, SC/APC, … or FC/APC fiber-optic connectors. You can use the CohSol SwitchPXIe-1003-1 for repeatable, low-loss switching.
-
product
Optical to Electrical Converters
High bandwidth, broadband optical to electrical converters available in a range of configurations. Choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
Automated Optical Switch - MATRIQ
Add optical switching capability to your test system with Quantifi Photonics’ automated optical switches. The fast and reliable optical switch will enable automated sequential testing, saving time and streamlining your test procedures.
-
product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
Optical-Electrical Converter - MATRIQ
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
Broadband Optical Source - MATRIQ
Our SLED MATRIQ instrument is a compact super-luminescent LED light source with high output power, large bandwidth and low spectral ripple.The SLED comes in various wavelength models to address various key applications across telecom and datacom, and is ideal for building a customized optical testing platform that delivers reliable and repeatable results.
-
product
Desktop stand-alone
All Three Sensors Of Optical Comb Can Be Installed On The Gate Type Stage And It Can Be Used As A General-Purpose Stand-Alone Machine. Tasu Since It Is A Rectilinear Laser, Complex Shapes Can Also Be Measured Tasu Measuring Time With A Working Distance exceeding 100 mm can be easily measured + parts with high irregularities can be measured with deep depth of focus
-
product
Radiating Comb Generators
TBCG1
The TBCG1 is a radiating comb generator with an internal antenna and a base frequency of 100MHz. It radiates a comb spectrum characterized up to 6GHz. The comb generator is built and characterized to serve as a rough reference for testing radiated noise measurement set ups in anechoic chambers, TEM/GTEM cells, shielded chambers, etc.
-
product
Comb Generators
As an EMC testing lab, the accuracy of your results is key to your reputation. Maintaining this accuracy requires properly calibrated quality equipment. Comb generators are an important piece of EMC radiated emissions testing equipment - one that can save you time and money by reducing your reliance on full, annual recalibrations of your site and instrumentation.
-
product
Plastic Wet Film Combs
154
Metric and Imperial values are on the same comb, 50 to 800μm on one side, 2 to 32mils on the other.
-
product
Uncured Powder Film Comb
155
This enables the application system to be set up and fine tuned prior to the curing process. In turn, this will reduce the amount of scrap and over-spray.Place the comb into the powder and slide the comb along the surface. The measurement points (or teeth) are pointed and allow the powder to flow around them.
-
product
Comb Generator
WJ10-50A
Comb Generator model WJ10-50A with Broadband Antenna. Frequency Range 10 MHz - 11.0 GHz with two frequencies step option; 10/50 MHz
-
product
USB Harmonic Comb Injector
J2150A
The USB Harmonic Comb Injector is a fast, easy-to-use, ultra-portable signal generator for interrogating your PDN to identify noise sensitivities. Quickly identify power supply related issues. Multiple modes include time and frequency jitter. Wideband harmonic comb spans 1kHz-1GHz+. Great for clock power supply EMI spectrum testing.
-
product
Comb Generator, 10 MHz to 67 GHz
U9391G
The Keysight Technologies, Inc. U9391G comb generators were developed to provide precision phase calibration, for non-linear measurements using the PNA-X nonlinear vector network analyser (NVNA), referenced to the National Institute of Standards and Technology (NIST) standard. Additionally, the comb generators can be used to calibrate PNA and PNA-X network analyzers for phase and delay measurements of frequency converters without requiring reference or calibration mixers.
-
product
Frequency Doubling Comb Generator
COMBGEN6DIFF
*Differential output - can also provide two separate single ended complementary outputs.*Pulse height of up to +4V peak into 50 ohms, on positive output*Pulse height of up to -4V peak into 50 ohms, on negative output*Rise time < 80pS, FWHM of approximately 120pS*Produces pulse on both edges of input clock, thereby doubling frequency.*Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz.*Usable energy to >10GHz.*Can drive any load, including short, without damage.*Power Requirements: -12V @ 120mA and +24V @ 80mA
-
product
Microwave Comb Generator
*Differential output - can also provide two separate single ended complementary outputs. * Pulse height of up to +4V peak into 50 ohms, on positive output * Pulse height of up to -4V peak into 50 ohms, on negative output * Rise time < 80pS, FWHM of approximately 120pS * Produces pulse on both edges of input clock, thereby doubling frequency. * Input clock may be sinewave from 50MHz to 2GHz or square wave from 5MHz to 2GHz, producing fundamental comb tooth energy from 10MHz to 4GHz. * Usable energy to >10GHz. * Can drive any load, including short, without damage. * Power Requirements: -12V @ 120mA and +24V @ 80mA
-
product
Broadband Optical Source - PXI
SLED 1000 Series
The SLED 1000 Series is a super-luminescent LED light source with high output power, large bandwidth and low spectral ripple. It comes in various wavelength models to address applications in the telecom and datacom markets.The SLED is a single-slot PXIe module and is ideal for building a customized optical testing platform that delivers reliable and repeatable results in manufacturing or R&D environments.
-
product
Comb Generator
CG 50/500
The main application of Conducted Comb Generator is to quickly verify conducted emissions test setups. And the most important application is trouble conducted measurements using an ISN. reference signal source Noise Generators Signal Generators
-
product
Hexagonal Wet Film Combs (Stainless Steel)
112 & 3236
These hexagonal precision formed stainless steel wet film combs are long lasting, reusable and supplied in a range of thicknesses measuring up to 3,000μm (120mils).
-
product
Punched Wet Film Combs (Aluminium)
112AL
The Elcometer 112AL, being punched from aluminium, is not as accurate as precision formed stainless steel wet film combs and has a shorter lifespan.
-
product
Optical Link
OPT-2
The OPT-2 Optical Link allows the THERMES-USB to be operated with total optical isolation between THERMES and the host computer. USB Isolation device offers up to 4500 volts DC isolation.
-
product
Optical Tester
Model C
The Model C Optical Tester is just such a device. Extremely small geometric distortion and focal length deviation can be viewed and measured easily.
-
product
Comb Generator
RefRad X
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
product
Optical Analyzers
DNIRA™
Neolitics’ DNIRA™ is a real-time, in-line process NIRS that delivers the performance and accuracy of a precision laboratory instrument in a compact, robust, in-line design. It’s easy to install and requires virtually no maintenance post-installation, eliminating the time and difficulty required to keep systems calibrated and the difficulty in replicating or scaling applications within a manufacturing environment.
