Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
Product
Auditor Torque Cube
ATC Series
-
The Auditor Torque Cube (ATC) is a compact, versatile desktop tester and provides a multitude of capabilities. The ATC is designed to test hand or power tools with the following: Peak, first peak and track modes. Multiple engineering units. Manual and auto clear function. Multiple frequency response settings. Bi-directional use and accuracy. Accuracy is better than 1% of indicated reading top 90% of range. Serial data output. Memory 999 data samples. Battery and/or mains powered.
-
Product
Bit Synchronizer Daughterboard Rates up to 25 Mbps
LS-40-DB
-
The Lumistar LS-40-DB Bit Synchronizer Daughterboard provides optimal reconstruction of a serial PCM data stream that has been corrupted by noise, phase jitter, amplitude modulation, or base line variations. The all-digital design assures a high performance, consistent product, with excellent reliability and long-term stability.
-
Product
RS232/422 Strobe Mux III Card & Panel
9565-16
-
16 serial port ISA compatible card connected by 4.8 ft (1.5m) cable and terminated as male DB25 connectors on external panel 7.6" high x 13" wide x 1" deep (193 x 330 x 25 mm).
-
Product
SparkFun Dev Board
ESP8266 Thing
-
This is the SparkFun ESP8266 Thing Dev Board – a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective, and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors, or automate coffee makers, and with an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any Internet-connected project. To top it all off, the ESP8266 is incredibly easy-to-use: firmware can be developed in Arduino, and uploaded over a simple, serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
PMC-BiSerial II-NG1
-
The PMC BiSerial-II NG1 is part of the PMC Module family of modular I/O components by Dynamic Engineering. The PMC BiSerial-II is capable of providing multiple serial protocols. The NG1 protocol implemented provides two full-duplex RS-422 UART interfaces with error detection, two half-duplex RS-485 custom "index" interfaces, external clock input, two clock outputs, and various discrete signal inputs and outputs, all using RS-485 transceivers
-
Product
Rugged Ethernet System Supporting up to Four Independent 8000 Family Avionics Communication Modules
ES-9810/xx
-
The ES-9810/xx is a rugged ethernet system supporting up to four independent 8000 family avionics communication modules, allowing multiple different protocols to be mixed and matched in a single system. Modules available include MIL-STD-1553, MIL-STD-1760, MMSI, ARINC-429, ARINC-708, ARINC-717, Serial, Discrete and CAN bus.The ES-9810/xx is supplied with C drivers, including source code. Mating connectors and cable adapters for I/O connection can be purchased seperately.
-
Product
mSATA SSD Carrier
SD3-GLISS
-
SD3-GLISS fits into any CompactPCI® Serial peripheral slot that is PCIe enabled. Hardware RAID operation is supported, running with an enhanced ARM-based processor to offload the host CPU.
-
Product
8-Channel A/D & D/A Zynq UltraScale+ RFSoC Processor - QuartzXM
Model 6001
-
- Now available in RFSoC Gen 3 with the Model 6003- Unique QuartzXM eXpress Module enables deployment in custom form factors- Supports Xilinx Zynq UltraScale+ RFSoC FPGAs- 16 GB of DDR4 SDRAM- Measuring only 2.5 by 4 inches- LVDS connections to the Zynq UltraScale+ FPGA for custom I/O- GTY connections for gigabit serial communication- Ruggedized and conduction-cooled versions available- Includes a complete suite of IP functions and example applications- Model 8257 1-Slot 3U VPX Development Chassis for Quartz Products
-
Product
RS232 / RS485 / RS422 / TTL Serial Repeaters & Hubs
-
CommFront offers a range of rugged, industrial-grade RS232 / RS485 / RS422 / TTL repeaters and hubs to meet serial communications' data distance needs by converting unbalanced signals to balanced ones, deploying repeaters to boost signal strength, and implementing hubs for star-configured connections, while still taking full advantage of cost-effective and readily-available copper wire.
-
Product
Serial FPDP Extreme 1/2 ATR Recorder
Talon RTX 2596
-
- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed, conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 18 lb (8 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Four-channel Serial FPDP record/playback- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- Single-mode and multi-mode fiber interfaces available- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
Product
Low Cost Emulator
EB-76X
-
* Emulates Philips Low-Pin Count Microcontrollers * Real-Time and Transparent Emulation up to 20MHz * 4K Emulation Memory * Real-Time Trace * Uses Philips Bond-Out Technology * 3.3V and 5V Operation * Software for MS-Windows * High-Level Support for Popular C-Compilers * On-Line Assembler and Disassembler * Emulation Header and Signal Testpoints * Power Supply Included * Serially linked to IBM PC at 115 Kbaud
-
Product
RS422/RS485 Serial Boards
104-COM-8S
-
These are eight, four, or two-port, asynchronous, serial communication boards designed for use on the PC/104 bus. They support RS-485 and RS-422 communications. The boards may be installed in any standard PC/104 stack. Connections are made via a 50 pin IDC type right angle connector.Common applications include POS, gaming systems, machine monitoring, military and high-density networking.
-
Product
OnyxFX FlexorSet 8-Channel 250 MHz A/D with DDCs - 3U VPX
Model 5973-317
-
- Supports Xilinx Virtex-7 VXT FPGA- GateXpress supports dynamic FPGA reconfiguration across PCIe- Eight 250 MHz 16-bit A/Ds- Eight multiband DDCs- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- PCI Express (Gen. 1, 2 and 3) interface up to x8- User-configurable gigabit serial interface- Optional optical Interface for backplane gigabit serial interboard communication- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Compatible with several VITA standards including: VITA-46, VITA-48 AND VITA-66.4 and VITA-65 (OpenVPX™ System Specification)Ruggedized and conduction-cooled versions available
-
Product
LAN⇔RS-232C(2ports) Converter
SI-60X
-
SI-60X is an interface converter that converts 2 serial ports of RS-232C devices to Ethernet LAN at 10Base-T/100Base-TX. The built-in Lantronix WiPort® NR on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. The small housing ensures ease of use for FA applications, public facility and medical institution as a communication device server.
-
Product
DH Series QuickLink Adapter, 8 GHz BW
DH-QL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
Test FMC Mezzanine Module
TFMC900
-
The TFMC900 is an FMC (FPGA Mezzanine Card) Mezzanine Module designed to test ANSI/VITA 57.1 FMC Carriers during development or series production. Additionally, it offers the possibility to realise various I/O solutions for connected FMC Carriers. Interconnection of the High Pin Count FMC Connector signals can be verified by JTAG and by functional tests. A loop-back of the 10 multi-gigabit transceiver interfaces allows interconnection checks for the high-speed serial interfaces.
-
Product
3U CompactPCI® RS-232/422/485 Serial Communication Card
MIC-3955
-
The MIC-3955 is a low power 4-port or 8-port RS232/RS422/RS485 serial board with 3U CPCI form factor and is based on the EXAR PCI controller. MIC-3955 is PICMG 2.0 Rev. 3.0 compatible. Rear board module are named MIC-3527XX. The MIC-3955 supports front IO or rear IO with 4-port and 8-port, and every channel is independent.
-
Product
Smart GPIB Serial Interface Board
Model 4808
-
* Provides smart GPIB-to-serial path for serial devices with RS-232, RS-422 or RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Rear panel mounting eliminates cables.
-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
-
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
Product
Oscilloscope
DSOX3032A
-
350 MHz2 analog channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 4 Mpts memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, memory, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time
-
Product
Fixed Gas Detectors
MicroSafe 500 & 600 Series
-
Teledyne Gas & Flame Detection
MicroSafe 500 and 600 Series gas detectors feature a non-intrusive operator interface. Calibration and programming instructions appear in simple intuitive and sequential script on a 16-character backlit display. The transmitter design incorporates extensive fault diagnostics with each condition conveniently identified on the transmitter display.The 500 Series comes standard with a linear 4-20 mA output, one-man remote calibration, self-adjusting zero and span, and LED indicators for fault and calibration status.The 600 Series includes the same features as the 500 with the addition of 3 alarm relays and an RS-485 serial communications port.Electrical Classification - Explosion proofClass I, Div 1, Groups B, C, D
-
Product
Oscilloscope - 200 MHz, 4 Analog Channels
DSOX4024A
-
200 MHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary WaveGen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
Isolated Serial To Analog Interfaces
-
ICS's Serial to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Available in rack mountable Miniboxes™ and IN OEM board versions. All of ICS's Serial to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
Product
Serial to Relay Minibox™
Model 2364
-
* Model 2364-11 provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Includes 50-pin mating connector for solder connections.* Optional 1 'U' high Rack Mounting Kits hold one or two 2364s.* Optional 115750 Terminal Board and Terminal Strip for easy connections without soldering. See the Serial Accessory page.
-
Product
cRIO-9063, 667 MHz Dual-Core CPU, 256 MB DRAM, 512 MB Storage, Zynq-7020 FPGA, 4-Slot CompactRIO Controller
783830-01
-
667 MHz Dual-Core CPU, 256 MB DRAM, 512 MB Storage, Zynq-7020 FPGA, 4-Slot CompactRIO Controller - The cRIO-9063 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. Additionally, the cRIO-9063 features an SDHC slot and a variety of connectivity ports, including one tri-speed RJ-45 Gigabit Ethernet, one USB host, one USB device, and one RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
USB
-
Universal serial bus, or USB, is an industry standard that defines the cables, connectors and communication protocols used to connect computers and peripherals. ST's portfolio covers a wide range of products designed for USB data (transceivers) and/or power applications (battery chargers and charger detection systems).
-
Product
ACC-188 Synchronous Serial Radio Adapter
-
The ACC-188 synchronous serial radio adapter is interoperable among various tactical radio brands and models used by the defense community. The ACC-188 works with any radio that has a synchronous serial communication port using MIL-STD-188-184 and enables the tactical radios to send data such as GPS maps, images, coordinates, and IM-type communications.
-
Product
CIE Colorimeter Probe
K-1
-
The Klein K-1 tri-stimulus CIE Colorimeter Probe is designed to be the best colorimeter in sensitivity, stability and speed. It attaches directly to a pc's serial com port (RS-232), and runs with the companion pc program. Whether a desktop or a laptop is used, the Klein measurement application is in control and many additional features are available.
-
Product
Multiprotocol P104Plus Interface Board for Embedded Applications or Avionics Test & Simulation Applications
EXC-4000P104plus
-
The EXC-4000P104plus is a multiprotocol P104plus interface board for embedded applications or avionics test and simulation applications. Each board holds up to five independent modules. Two on-board modules use the MIL-STD-1553 communications protocol (M4K1553Px); another on-board module uses the ARINC-429 communications protocol; two additional detachable modules can be any one of the following types:M4K1553PxS (Single Function - RT validated) This module operates as a Bus Controller, Remote Terminal or a Bus Monitor. This module qualifies for airborne applications.M4K1553Px (Multi Function) This module operates as a Bus Controller, up to 32 Remote Terminals and as a Bus Monitor. Supports an Internal Concurrent Monitor in RT and BC/RT modes.M4K1553Px(S)-1760 Same as M4K1553Px(S) plus MIL-STD-1760 options.M4KMMSI Mini Munitions Store Interface module. Supports RT, BC/Concurrent-RT/Concurrent Monitor and Bus Monitor modes. Up to 8 hub ports EBR-1553 [10 Mbps 1553 protocol using RS-485 transceivers] and 1 monitor output.M4KH009 Based on our H009 family. This module operates as a Central Computer Complex (CCC) and/or up to 16 Peripheral Units (PUs) simultaneously, or as a Bus Monitor. In addition, a Concurrent Bus Monitor enables concurrent monitoring of the bus during CCC and PU simulation.M4K429RTx Based on our ARINC 429RxTx board. This module supports either five or ten ARINC 429 channels each of which can be configured in real time as a receive or transmit channel.M4K708 This module supports two channels of ARINC 708/453, each one selectable as either transmit or receive.M4KSerial This module supports up to 4 independent channels of serial communications, each of which can be selected as RS485, RS422 or RS232.M4KDiscrete This module supports 20 selectable input/open collector output discretes. The module supports TTL (0 to 5 volts) or avionics (0 to 32 volts) voltage levels.M4KCAN This module supports up to 6 independent channels of CAN 2.0B protocol with standard and extended message frames and message identifiers.
-
Product
PXIe8862, 2.6 GHz 8-Core PXI Controller
790660-01
-
The PXIe8862 is an Intel Core i7 8Core embedded controller for PXI Express systems. You use the PXIe8862 for processor-intensive RF, modular instrumentation, and data acquisition applications. The PXIe8862 includes two 10/100/1000/2500BASET (Gigabit) Ethernet ports, two USB 3.0 ports, four USB 2.0 ports, as well as an integrated hard drive, serial port, two Thunderbolt 4 ports, and other peripheral I/O.
