A/D Converters
quantization of an analog signal into a digital signal.
-
Product
HDG and OBS Track Select Panel
TA-260
-
Universal Heading and Track Selector Panel This panel provides a synchro transmitter for Heading and a synchro resolver for Nav converter alignment. The synchros are mounted on industry standard 18:1 dual speed drives for maximum accuracy and repeatability. This unit can be used to calibrate both manual and automatic converters. This panel provides a rear mounted interface connector as well as front mounted tip jacks for independent breakout if so desired. The TA-260 also provides two discrete switches associated with the resolver configuration. The 30Hz/400Hz switch is provided to allow the resolver to be properly compensated for the type of Nav converter to be aligned. The second switch allows you to open or short the resolver rotor lead as may be required by some newer GPS equipment. This panel is lightweight enough for portable use or may be rack mounted.
-
Product
Analog Output Data Acquisition (DAQ) Products
-
Analog Output boards are useful when you need an output where the condition is not just an on or off state. Analog Output boards convert digital values generated by software into the analog voltage or current signals required for controlling frequency inverters, valves, sliders, brightness of lights, or things controlled by motors and other mechnical transducers.
-
Product
PXIe-7858, Kintex-7 325T FPGA, 1 MS/s, DRAM PXI Multifunction Reconfigurable I/O Module
784147-01
Multifunction Reconfigurable I/O
Kintex-7 325T FPGA, 1 MS/s, DRAM PXI Multifunction Reconfigurable I/O Module—The PXIe‑7858 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7858 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7856 also includes peer‑to‑peer streaming for direct data transfer to other PXI Express modules.
-
Product
ADC DAC Module
ZET 220
-
ZET 220 ADC DAC module with 24-digit ADC converters is used for high-precision signals measurements in wide dynamic range. The signals to be measured are received from primary transducers – for instance, from sensors with 4-20 mA current output.
-
Product
IRIG Time Code Receiver & Generator Module
TCR180
-
Meinberg Funkuhren GmbH & Co. KG
The module TCR180 has been designed to receive and to generate IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device. The frequency locking of the master oscillator to the time code system enables this module to generate fixed and programmable standard frequencies with high accuracy and stability. Various oscillator options allow the cost efficient implementation of different requirements concerning the accurracy of the outputs. The generator of the IMS-TCR module generates pulses per second and per minute and per hour. Four programmable outputs are also available. The pulses are synchronized to UTC-second.
-
Product
4-Quadrant General-Purpose Source/Measure Unit, ±20 V, ±1 A Or ±6 V, ±3 A, 20 W
N6784A
Source Measure Unit
The Keysight N6784A is a source/measure unit (SMU) designed for general-purpose precision sourcing and measurement. General-purpose applications can span many different industries and many different devices under test (DUTs). The N6784A SMU is a versatile tool designed to tackle many of these general-purpose applications. Its glitch-free operation ensures safe usage with the DUT during output and measurement range changes, even with capacitances of up to 150 µF. Its 4-quadrant operation enables it to act as a bipolar power supply or a bipolar electronic load, for added versatility. When using the N6784A SMU, engineers can be confident that they have an all-around general-purpose tool for their test systems or lab bench.
-
Product
AC-AC Converters
-
AC/AC converters, also known as frequency converters or voltage converters, are electronic devices used to convert electrical energy from one type of alternating current (AC) to another alternating current with a different frequency or voltage. Start Power offers single-phase stabilisers, three-phase stabilisers and energy saver static converters.
-
Product
Geophysics
ELETOM
-
ELETOM is a software that performs complete 2D inversion (and not the simple iterative deconvolution of the pseudo-sections) of surface electrical surveys with any measurement array (Wenner, dipole-dipole, pole-dipole, pole-pole, user defined arrays, mixed arrays) with a maximum of 64 electrode positions that can be added by the user as required.
-
Product
Domino Symphony PCIe
-
Four 10-bit 65 MHz A/D converters with four 8- or 10-bit LUTsPCIe x1 busD³ technology for extremely low synchronization jitterSupport for mega-pixel progressive-scan and interlaced cameras, asynchronous reset and exposure controlTrigger, strobe and general purpose I/O lines
-
Product
4-Channel 200 MHz A/D with DDC, Virtex-7 FPGA - PCIe
Model 78761
-
Model 78761 is a member of the Onyx® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter withprogrammable DDCs (Digital Downconverters), it is suitable for connection to HF or IF ports of a communications or radar system. Its built-in data capture feature offers an ideal turnkey solution as well as a platform for developing and deploying custom FPGA processing IP. It includes four A/Ds and four banks of memory. In addition to supporting PCI Express Gen. 3 as a native interface, the Model 78761 includes an optional connection to the Virtex-7 FPGA for custom I/O .
-
Product
Additional hardware for our test systems
-
REINHARDT System- und Messelectronic GmbH
Our test systems are made up of modules which can be added to the needs of our customers.
-
Product
Diamond-like Carbon (DLC) Foils
-
An intense laser beam is used to evaporate carbon from a graphitic sputter target. In the process, the graphite structure of the source material is converted into nano-particles, which deposit on prepared substrates as diamond-like carbon. The properties of these unique carbon foils make them useful in a variety of applications, in particular beam stripping, as backings for accelerator targets or x-ray attenuators.
-
Product
PC/104 OneBank Board
EMC²-7K325
-
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-7K325 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-Kintex7T also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options
-
Product
Linear Array Detector Cards
X-Card 0.2 to 2.5mm
-
A product family of high performance linear X-ray detector cards with preamplifier ASICs. The preamplifier ASIC converts the charge output from the photodiode array into voltage with serial output for easy integration with readout electronics. Can be arranged end-to-end to form large linear detector arrays.
-
Product
3-Ch 200 MHz A/D with DDC & 2-Ch 800 MHz D/A with DUC, Virtex-7 FPGA - XMC
Model 71721
-
- Complete radar and software radio interface solution- Supports Xilinx Virtex-7 VXT FPGAs- GateXpress supports dynamic FPGA reconfiguration across PCIe- Three 200 MHz 16-bit A/Ds- Three multiband DDCs (digital downconverters)- Two 800 MHz 16-bit D/As- One DUC (digital upconverter)- Multiboard programmable beamformer- 4 GB of DDR3 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multimodule synchronization- PCI Express (Gen. 1, 2 & 3) interface up to x8- VITA 42.0 XMC compatible with switched fabric interfaces- Optional LVDS connections to the Virtex-7 FPGA for custom I/O- Supports GateXpress® FPGA-PCIe Configuration Manager- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
Temperature and Humidity Bar Type Probe
T3117
-
Relative humidity, temperature sensors at 700mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
FPGA Mezzanine Card
FMC126
-
The FMC126 is a quad-channel multi-mode A/D FMC, fully compliant with VITA 57.1 standards.The card provides four 10-bit ADC channels that enable simultaneous sampling of 4, 2, or 1 channel with a maximum sample rate of 1.25 GSPS (4-channel mode), 2.5 GSPS (2-channel mode), or 5.0 GSPS (1-channel mode).
-
Product
PXIe 8 Bit High Speed Digitizer - 1.25 GS/s on 4 Channels, 500 MHz Bandwidth
M4X.2212-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
Micro probes 1 MHz up to 1 GHz
MFA 02 set
-
The two in the set included micro probes are used to measure low-frequency magnetic fields up to 1 GHz, e.g. at signal conductors (150µm), SMD componets (0603-0201) or IC pins. The MFA micro probes are guided by hand. An amplifier stage is integrated into the probe head. The amplifier stage (9V, 100mA) is powered via the BT 706 Bias tee. It has an impedance of 50 Ohm. The micro probes are connected via the Bias tee to a spectrum analyzer or an oscilloscope. The MFA 02 set delivery of Langer EMV-Technik GmbH includes correction lines. With the help of the correction lines the probe output voltage is converted either into the respective magnetic field or to the current which is running through the conductor.
-
Product
Converter
-
Converter and driver chips ensures data rates above 1 MBaud and therefor reliable data transmission also with highest rates.
-
Product
4-Channel DAQ Module
FMC176
-
Sundance Multiprocessor Technology Ltd.
The FMC176 is a quad channel ADC and dual channel DAC FMC. This daughter card provides four 14-bit A/D channels at 250Msps and two 14-bit D/A channels at 5.6Gsps (2.8Gsps direct RF synthesis) clocked by either an internal clock source (optionally locked to an external reference) or an externally supplied sample clock. In addition, a trigger input for customized sampling control is available to users. The FMC176 daughter card is mechanically and electrically compliant to the FMC standard (ANSI/VITA 57.1).
-
Product
Isolated RS-232 To RS-422/485 Converter
ADAM-4520
-
Automatic RS-485 data flow control3000 VDC isolation protectionSurge protection RS-485 data lineTransmission speed up to 115.2 KbpsLED indicator to monitor status
-
Product
24 TTL Channels, Enhanced, Programmable I/O
TL2
-
Function module TL2 provides 24 channels of TTL/CMOS transceiver functionality as either inputs or outputs. The transistor-transistor logic (TTL) employs transmitters with multiple emitters in gates having more than one input. TTL offers high switching speed and relative immunity to noisy systems. CMOS sensors provide image sensing technology by converting light waves into signals that are small bursts of current. These waves can be light or other electromagnetic radiation.
-
Product
Linear DC Power Supply
-
A device that takes AC current (mains or line current, depending upon where in the world you are) and converts it into safe low-voltage DC at the desired voltage level.
-
Product
PLCC-to-DIP Adaptor
Series 352000/353000
-
PLCC to DIP Adapter. Converts PLCC packaged ICs to DIP footprints. Available with PLCC sockets or PLCC pads on top side. Consult factory for panelized form or for mounting of consigned ICs.
-
Product
PXIe 8 Bit High Speed DIgitizer - 1.25 GS/s on 2 Channels, 500 MHz Bandwidth
M4X.2211-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
X-Ray Fluorescence Analyzer
MESA-50K
-
In order to meet RoHS/ELV and to analyze hazardous elements, HORIBA has offered the X-ray Fluorescence Analyzer XGT-1000WR series. Since 2002, 1000 units have been used all over the world for these applications to meet the critical needs from our customers to analyze the sample without cutting it. In 2012, an intuitive MESA-50 X-ray Fluorescence Analyser was released. It became every popular in a very short amount of time, and in 2013 a new type of MESA-50 with a big sample chamber has been added to the MESA-50 series. It is equipped with the sophisticated LN2-free detector. As/Sb analysis function and Multilayer Film FPM are available as options.
-
Product
Radar Scan Converter PMC
Eagle
-
Curtiss-Wright Defense Solutions
Eagle is a flexible and powerful radar scan converter that is based upon field-proven technology and comes in a compact and mechanically ruggedized PMC form factor. Eagle features a low power, rugged design, enabling it to operate in a wide range of environments, including conditions of high temperature and vibration.
-
Product
Adaptive Relay, Virtex-6 FPGA - 6U VPX
Model 57624
-
- Modifies 34 IF signals between input and output- Up to 80 MHz IF bandwidth- Two 200 MHz 16-bit A/Ds- Two 800 MHz 16-bit D/As- 34 DDCs and 34 DUCs (digital downconverters and digital upconverters)- Signal drop/add/replace- Frequency shifting and hopping- Amplitude boost and attenutation- PCI Express Gen 1: x4 or x8- Synchronize up to eight modules with Model 7893 System Synchronization and Distribution Amplifier - PCIe
-
Product
2U Data Processing Computer
CP42102
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP42102 is a 2U ruggedized data processing computer compliant with PICMG CompactPCI® specifications. With ruggedized conduction cooling structure and CompactPCI® module design, CP42102 has excellent performance on heat dispassion and anti-vibration, and can save costs on maintenance in the long run.CP42102 can meet the demands for big data processing, computing and storage, as CP42102 is equipped with a 3rd Gen embedded Core™ i7 high-performance processor with up to 16GB memory and 1TB storage. On CP42102, interfaces like Ethernet, USB, serial ports, VGA, etc. are routed to the rear through aviation plugs; inside the chassis, CPU slot and 2 service slots are connected by 1x LVTTL; outside the chassis, 2 N50K RF interfaces are added for external interconnection.
