D-Sub
D-Subminature Connector Also known as: DSub
-
Product
Cable Assembly, Receiver, 20", TriPaddle, 50 Pin FML D-Sub
540111020103
Cable Assembly
Cable Assembly, Receiver, 20", TriPaddle, 50 Pin FML D-Sub.
-
Product
10-Pin RJ50 Male to 9-Pin D-SUB Male Serial Cable
182845-03
Serial Cable
S8 Serial Cable, 10Pos Modular Plug to DB-9, 3 m (non isolated)
-
Product
CABLE ASSY, Type SH100-100-FLEX, 2 m
185095-02
Multifunction Cable
CABLE ASSY, Type SH100-100-FLEX, 2 m
-
Product
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
782015-02
Multifunction Cable
DB25F-DB25F, 25-Pin D-Sub Cable for SMUs, Low Leakage, 2 m
-
Product
68-Pin VHDCI Male to 8-Port 9-Pin D-SUB Male, Serial Cable
197545-01
Serial Cable
Serial Cable - 68-POS VHDCI to DB-9M, 8-Port RS-232, 1M
-
Product
30" Ribbon Cable
CONM50-D37-30
-
A 30" ribbon cable transitions from individual IP modules on various carrier boards to a 37 pin D-sub female connector mounted on a PC expansion card end-panel. This allows external connection to pins 1-37 on an individual IP Module.
-
Product
PCI Expansion Card
4624-4
-
VECTOR Electronics and Technology, Inc.
120 contacts (60 each side) on 0.050" centers. Pad-Per-Hole & Peripheral Buses. 32-bit ISA format. Universal tab fits both 3.3V and 5V tab notch patterns. Mounting bracket included. Peripheral buses for voltage and ground distribution. I/O mounting area for D-sub and ribbon cable connectors.
-
Product
4 Port RS-232 & 4 Port RS-422 Interface cPCI Card
GX3904
cPCI Card
The GX3904 is an 8-port, cPCI asynchronous communications interface board supporting (4) RS232 and (4) RS422 signal levels. The four RS232 ports offer a full set of data and modem control lines configured for DTE operation. The four RS422 ports offer differential signaling and support DTE operation. Each RS422 differential pair is terminated by a 150 parallel resistor. An optional transition cable is available to convert the front panel SCSI connector to (8) DB-9, D-sub connectors.
-
Product
18" Ribbon Cable
CONM50-D25-1
-
An 18" ribbon cable transitions from individual IP Module ribbon connectors on the ISA (PC/AT) carrier board to a 25 pin female D-sub connector mounted on a PC expansion card end-panel.
-
Product
37-Pin D-Type Male Solder Bucket
92-960-037-M
D-Sub Male Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires. 37-Pin Female connectors can be directly mated to a corresponding Pickering Switching Module while Male versions can be used to interface to a Female cable assembly termination.
-
Product
Connector, 104-Pin D-Type Male, Solder Bucket, 5A
92-960-104-M
D-Sub Male Connector
This 104-pin male D-type connector allows users to create their own cable assemblies. Cable connection is via solder buckets - supplied without backshell. This connector is not compatible with Pickering modules that use the 104-pin D-type connector.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 72", 78-Pin FML D-Sub
540112020540
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 72", 78-Pin FML D-Sub.
-
Product
1' Harness, 78-Pin Male D-Sub Connector
GT97104
-
1' harness, 78-pin male D-sub connector on both ends
-
Product
Configuration Block For The 34934A Quad 4x32 Reed Matrix
34934C
Terminal Block
This configuration block provides flexible options for wiring rows and columns to D-Sub connectors.
-
Product
Low Profile I/O Cable, 25-Pin Female DSUB to Male DSUB (1m)
154742-01
Multifunction Cable
Low Profile I/O Cable, 25-Pin Female DSUB to Male DSUB (1m)
-
Product
DB25 Cable
PCL-10125
-
Double-shielded cable with 25-pin D-sub connectorsD-Sub 25 pin male, Blue x 2Tinned and strand copper wire with drain wire x 1Aluminum/Mylar foil and braided copper double-shielded cable effectively reduces EMI (electro magnetIsolated P.V.C. jacketUL20397 approvedIvory color
-
Product
PCI Express Digital I/O Boards
PCI-P8R8
-
PCI Board with 8 Channels of Isolated Digital Input and 8 Relay Outputs. Includes one CA-4002 D-Sub connector
-
Product
37-Pin D-Type Female Solder Pin HV
92-960-037-F-HV
D-Sub Female Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed.
-
Product
50-Pin D-Conn Female Straight PCB
40-963-050-SF
D-Sub PCB-Mount Connector
Ideal for user created termination schemes where the termination is to be on the front or remotely connected to the module by cable. Suitable cables for this product are detailed in the data sheet. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
Breakout Box
T1000-15
-
T1000-15 breakout box with dual 15 pin D-Sub connectors for signal capture or monitoring. Dual connectors provide a total of 30 test points plus a ground jack. All test points use standard size 4mm banana jacks. Test points may be connected using shorting banana cable to allow signal continuity. Ideal for continuity measurements, isolation testing, and signal capture.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 78 PN FML DSub w/ T/P
540034050140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", 78 PN FML DSub w/ T/P.
-
Product
26-Pin D-Type Female Right Angled PCB
40-963-026-RF
D-Sub PCB-Mount Connector
Accessory allows a user to create their own PCB based termination solution mounted directly on the front of the product or on the end of a cable. Interfacing PCBs should be designed with suitable clearances for the voltage the application requires.
-
Product
3-Pin Power D-Type Connector, 40A, Female Without Backshell
92-960-003-F
D-Sub Female Connector
This connector is suitable for Pickering Interface's modules that use the 3-Pin Power D-Type connector. It is designed to allow users to make a direct termination with soldered connections.
-
Product
96 Channel DPST Relay And Control PXI Carrier Card
GX6196
Relay
The GX6196 is a 6U PXI switch and control board that can be used to create custom switching, signal conditioning, or specific UUT control interfaces. The board provides 96, 2 pole, form A relays, 8 digital I/O lines, and a serial digital interface. All of these resources are available via (5) inter-board connectors which interface to the user defined daughter / mezzanine board. The mezzanine board provides all connections to the unit under test (UUT) via two 78 pin D-sub connectors. The GX6196 is supplied with a front panel which accepts (2) 78 pin D-sub connectors.
-
Product
50-Pin D-Type Female Connector Block
92-965-050-F
D-Sub Female Connector Block
This connector block provides a simple method of connecting to 50-Pin D-Type connectors. The screw terminals use a rising cage clamp mechanism to minimize risk of copper strand breakage. PTFE cables are recommended for use with this connector block to maximise copper cross-sectional area and insulation properties.
-
Product
Cable Assembly, Receiver, QuadraPaddle, 20", 78-Pin FML D-Sub
540112020140
Cable Assembly
Cable Assembly, Receiver, QuadraPaddle, 20", 78-Pin FML D-Sub.
-
Product
Cable Assembly, Receiver, TriPaddle, 20", 50-Pin Female D-Sub
540018010101
Cable Assembly
Cable Assembly, Receiver, TriPaddle, 20", 50-Pin Female D-Sub
-
Product
4-Pin Power D-Type Female Connector, 40A, With Backshell
40-960-004-F
D-Sub Female Connector
This connector is designed to allow users to directly terminate a cable with soldered connections.
-
Product
PCI Daughter Boards
DB-24SSR/D (24-channel SSR Output Board)
-
The DB-24SSR/DB-24SSRDC includes 24 normally open, or form A, solid-state relays The board interface to filed logic signals, eliminating ground-loop problems and isolating the host computer from damaging voltages. The user can use the DB-24SSR/DB-24SSRDC to switch high voltage load, up to 240 VAC/50 VDC and up to 4 A. The relay is energized by applying a 5-voltage signal to the appropriate relay channel on the 50-pin header or 37-pin D-sub connector. Twenty-four enunciator LEDs, one for each relay, light when their associated relay is activated. Because there is a D-sub 37-pin connector on the board, the user may use it to interface to any TTL output board. In other words, the user may use it as a general purpose solid state relay output board.
-
Product
Solder Cup Connector Kit
Y1140A
D-Sub Female Connector
Used to build custom cables for 34922, 34924 – 78-pin Dsub female – 60 V
