Audio Amplifiers
This topic is for test equipment that is designed for the testing of audio amplifiers.
See Also: Amplifiers, RF Amplifiers, Preamplifiers, Current Amplifiers, Voltage Amplifiers, Transconductance Amplifiers, Op Amps, Klystron, Instrumentation Amplifiers, Distribution Amplifiers
-
product
Sensor Amplifier
UVM-SB
This is the relay amplifier box for the multi-point type UV monitors. Received UV light intensity is converted to electric signal for transmission. This allows distance between the light receiving inlet and the controller to 10 meters maximum.
-
product
Sample/Track and Hold Amplifiers
Analog Devices offers a portfolio of sample-and-hold amplifiers and track and hold amplifiers that combine speed with precision. ADI sample-and-hold amplifiers can acquire a signal in 700 ns and hold it with a droop rate of 0.01 µV/µs. These devices are up to 14-bit accurate, with low aperture jitter and output impedance, and they are available in commercial, industrial, and military temperature ranges.
-
product
Low Noise Amplifier
LNA
Teledyne Defence & Space (TDS) Low Noise Amplfiers (LNA) are designed to amplify very low power signals without degrading the signal-to-noise ratio.An amplifiers is designed to increase the power of both the signal and the noise however the Low Noise Amplifier is specifically designed to minimise the additional noise so important information should not be lost.
-
-
product
Power Amplifier
MS 2011
Power Amplifier is used to amplify the RF signals from low power to 100 Watts of RF carrier power to 400 Watts Peak envelop power (single side band operation). Outputs are filtered. This system is controlled through microprocessor and it has RS485 interface.
-
product
RF POWER AMPLIFIERS
BSA Series
RF Input: N-f, standard on rear panelRF Output: standard on rear panel<1 kW N-f<3 kW 7-16-f<5 kW EIA 1 5/8Mains Supply: Line Power:<1000 VA 100 ... 240 V AC ±10% / 47 ... 63 Hz1000 ... 3000 VA 200 ... 240 V AC ±10% / 47 ... 63 Hz>3000 VA 3x 400 V AC ±10% / 47 ... 63 HzElapsed Time Meter: via status displayAmbient Temperature: 0 ... +45 °CStorage Temperature: -20 ... +85 °CRelative Humidity: up to 95% (non-condensing)Operating Altitude: up to 2000 m above sea levelVibration and Shock: MIL-STD-810 GCooling: forced air with integral blowerair intake from front, air exhaust at rear
-
product
Traveling Wave Tube Amplifier
Skylink a leading provider in design and manufacture a wide range of traveling wave tube amplifiers(TWTAs) and microwave power modules(MPMs).Skylink's new generation of MPMs are based on a modular design, and use new technology, material and computer simulation system to improve weight, size and efficiency.Our main MPM series frequency covers range from 2 to 40GHz and providing more than 100W. They combine a helix TWT, a solid state amplifier and an integrated power conditioner in a compact package.
-
-
product
Signal Amplifier
ZET 410
The ZET 410 preamplifier is used as a signal amplifier in processing systems and various instruments and actuator control systems. It is used in industry, laboratory and mobile studies.
-
product
Femtosecond Optical Parametric Amplifier
CDP 2017
*> 30% conversion efficiency from pump pulse to parametric radiation*Wavelength conversion for ExciPro, TAPPIR, FOG 100-DA*Wavelength conversion options for wavelength tuning from 240 nm to 16 mm
-
product
I/O Board With Two COM, Four USB 2.0 And Audio For PICO312, PICO313, PICO511, PICO512
AX93A09
*Specification: 1 x RS-232/422/485, 1 x RS-232, 4 x USB 2.0, 1 x Audio (MIC-in/Line-out), 1 x Power-on, 1 x Reset, 2 x LED*Dimensions: 118 x 29 mm*Compliant products: PICO312, PICO313, PICO511, PICO512
-
product
Amplifier Built-in / U-shaped Micro Photoelectric Sensor [Ultra-small / Cable Type]
PM-25
Panasonic Industrial Devices Sales Company of America
The Panasonic PM-25 Sensor has a beam emitting / receiving distance of 6 mm. The beam emitting and receiving areas are 0.5 mm thinner compared to conventional models even though the external dimensions have not changed. As a result, the distance between the beam-emitting and the beam-receiving points have increased by 1mm thereby reducing the possibility of sensing objects colliding.
-
product
8 Plug Pro Audio Cable Tester
PCT10
Enables quick convenient continuity cable testing for all type of cablesLED's confirm each conductor continuity and connection6-Way Switch for selecting connections to be testedIncludes internal battery and ground connection status checkRugged, compact, metal construction for long life and reliabilityTests cables with all types combinations of the following connections3.5mm TRS Jack1/4' TRS Jacks3 Pin XLR Male3 Pin XLR FemaleRCA Phono4 Pin SpeakonBanana Plugs9V Batter (Not Included)
-
product
PHIL 4-Quadrant Power Amplifier
PAV5000
PAV5000 is the four-quadrant amplifier with high power applied in the semi-physical simulation power platform to analyzer the sensitive load, the equipment power adaptability, and the electric vehicle, etc. and provide the technical support and service on the power quality.
-
product
Audio Generator & Impedance Meter
MR-PRO/MR2
The Minirator MR-PRO provides a full set of analog audio signals including sine wave, pink noise, white noise, delay test signal, polarity test signal, stepped sweep and continuous sine sweep. Further, a set of wav-files, useful for system optimization, is stored in the internal flash memory. Add your own personal favorites to this set.
-
product
Broadband Power Amplifier
PAS-00023-25
* Solid State Power Amplifier* Gain : 46 dB typ.* High IP3, 48.0 dBm typ.* Bench Top Case* Internal Cooling Fans* Over Temperature Protection* Type N Connectors
-
product
AC/DC Power Pass Hybrid Amplifier
AS 1313 SMPS
- Low Power Consumption - Drive More Amplifiers- Special 6 Volt Module -For High OutputMultiple Power Options:- 12 Volt DC Adapter- DC Power Pass 40V- AC Power Pass upto 110 V
-
product
Charge Amplifier
This compact Charge Amplifier has 3 signal routes.When it is used as the Charge Amplifier for the vibration analysis systemWave Stocker, all setups are possibleby the upgraded software.
-
product
Digital andAnalog Distribution Amplifier
D/A-1
The D/A-1 Digital and Analog Distribution Amplifier is a digital and analog signal distribution product based on the the Intelligent Reference/TM-4D™ chassis and is the perfect way to distribute externally supplied signals without the need for multiple units. Most signal distribution products are limited to either analog or digital signals, but the D/A-1 distributes both.
-
product
Conventional Panel-mounted Type Power Amplifier Control Unit
PAT01
PAT01 is a power amplifier control unit that controls timing output and reference signal test source for power amplifier.
-
product
SV Range Broadband Power Amplifiers 0.8 GHZ - 3.2 GHZ
SV Series
Class A solid stateBroadband (instantaneous single band): 80 MHz 1000 MHzTypical output power : 100 W CWLinear output power (1 dB compression) guaranted with harmonics <-20dBc:P1dB > 100 W and H < -20 dBc up to 450 MHz andP1dB > 65 W and H < -20 dBc from 450 MHz to 1000 MHzAir cooling: self contained fansCan operate in full mismatch conditions without damageUpgradable to MT 200 possibleReliable, efficient and robust19" Rack3 years standard warranty
-
product
Reference plus Comparator or Amplifier
Analog Devices reference plus comparator or amplifier products combine the excellent initial accuracy and low overtemperature drift performance of single function voltage references with comparators, buffer amplifiers, and current sense amplifiers. These products offer compact solutions for a broad range of applications such as battery monitoring, threshold detectors, window comparators, auto power-off circuits, and low dropout (LDO) regulators.
-
product
Wizard Pocket Audio Monitor
AES/EBU
The AES/EBU Wizard is a hand-held digital audio monitor that receives AES/EBU audio at any sampling rate from 32kHz to 96kHz and displays the received sampling rate, lock status, and five different error conditions. It also has a headphone jack with volume control for monitoring digital audio sources.
-
product
CATV Separate Raman Amplifier
RFA4000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Amplifier is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. Raman amplifier is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
Isolation Amplifier
Mornsun Guangzhou Science & Technology
An isolation amplifier is an amplifier that provides isolation between the input and output of the circuits, including isolation between their associated power supplies. MORNSUN offers different types of analog isolation amplifiers, such as acquisition type signal conditioning modules, output isolation signal conditioning modules, two-wire loop power supply signal conditioning modules and signal isolators, etc. These analog isolation amplifiers feature excellent temperature drift characteristics of less than 50PPM/℃ across the entire operating temperature range of -40 ℃ to +85 ℃ and achieve isolation transmission, signal conversion (programmable for some models), HART communication, signal amplification, port protection and other functions. SIP, DIP, SMD and DIN Rail packages are optional.
-
product
FFT Audio Spectrum Analyzer Plug-in
SPAN Plus
Fast Fourier transform spectrum analyzer. Stereo, mid-side, surround spectrum analyzer. Stereo correlation meter. Multi-track spectrum comparison. PNG spectrum snapshot saving. K level meter. This plug-in is compatible with Windows (32 and 64-bit Windows XP, Vista, 7 and later versions) and Mac OS X (10.5 and later versions, 32-and 64-bit, Intel processor-based) computers.
-
product
Nano-ITX SBC With Intel® Celeron® Processor J1900/N2807, LVDS/VGA/HDMI, Dual LANs And Audio
NANO842
The NANO842 Nano-ITX motherboard is designed to support the Intel® Celeron® processors quad-core J1900 and dual-core N2807 (code name: Bay Trail). A DDR3L SO-DIMM socket located on the bottom of the board can support up to 8GB of DDR3L memory. It can handle operating temperatures from -20°C to 70°C, and runs on +12V DC input. This 120 x 120 mm industrial embedded board comes with multiple display outputs: HDMI, LVDS and VGA with visual experiences enhanced for dual-view supported. The Axiomtek NANO842 is an ideal solution aimed at embedded, industrial, and IoT applications.
-
product
Power Amplifiers
WBPA Series
Besides offering wide bandwidth, WBPA series wide band power amplifiers have exceptional gain flatness and ultra high linearity. The IP3 are from 40 dBm to over 50 dBm. The different models cover the frequency bands of VHF, UHF, Celular, GPS, DCS, PCS, 3G, MMDS, and S band. The amplifiers have optimum return losses, gain flatness, high power and high added power efficiency, wide bandwidth matchings, and unconditional stability.
-
product
Saluki SPA Series Solid State Power Amplifier (max. 23KW output power)
Saluki SPA series is a solid-state RF power amplifier with an output frequency of maximum 110GHz and an output power of a maximum of 23000W. Its design is based on the most advanced GaN technology in the industry, and its power output is efficient and reliable. The product has functions such as temperature and current detection, alarm protection and so on.The broadband solid state power amplifier is mainly used for testing and measuring instruments, Communication or interference, aviation control and other fields.*Customization Available*
-
product
1U, Rack Mount, Pulse Distribution amplifier
A5000P
The Quartzlock A5000P is a 1U, rack mount, pulse distribution amplifier
