Torque
turning force.
See Also: Torque Sensors, Torque Testers, Torque Transducers, Torque Meters, Dynamometers
-
Product
TorqueMate® Torque Analyzer
PTT-Series
-
The PTT torque meter makes quality documentation faster and easier. As an advanced torque controlling, monitoring and documentation solution, the torque analyzer enables operators and engineers to ensure product quality, safety and reliability promptly in a variety of manufacturing environments. The portable torque meters are designed for measuring torque, torque calibration, joint testing, auditing or force and load measurement. The failure of a three-cent fastener that isn’t properly tightened can lead to catastrophic or latent failures. Using a quality torque tester makes a safer world through accuracy and precision.
-
Product
Engine Dynamometer
DE250
-
Power: 335 hp (250 kW)Torque: 886 lb-ft (1,200 Nm)Speed: 8,000 rpmWater Use*: 47 gpm (177.9 lpm)Inertia Value: 11 lb·ft2 (0.464 kg·m2)Shipping Weight: 3,086 lb (1,400 kg)Rotation: bi-directional*No Cooling System
-
Product
Dynamic Torque Sensing System
-
Advanced Telemetrics International
Are utilized in applications where conventional rotary torque transducers are not practical due to excessive shaft speeds, vibration, and dirty, oily environments.
-
Product
Cap & Bottle
-
To ensure and control the manufacturing process of your bottles, flasks and corks, it is necessary to carry out periodic checks on the screwing torque of the corks or the strength of your bottles.
-
Product
Reduced Voltage Motor Starting Panels by Auto-Transformers
-
Reduced Voltage Motor Starting Panels are designed for starting of squirrel cage induction and synchronous motors. A RVMS Panel reduces the torque by temporarily reducing the voltage and/or current input. It reduces voltage applied to the motor during start up causing lower starting currents from the connected grid.
-
Product
Digital Strain Gauge Sensor
ZET 7111
-
The ZET 7111 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or separate external tension gauges connected using half-bridge or bridge scheme.
-
Product
Half Shaft Torque Measurement Systems
-
Advanced Telemetrics International
ATi’s Half Shaft Telemetry System transmits torque signals from rotating shafts to a stationary telemetry receiver. It connects directly to strain gages adhered to the shaft converting it into a torque sensor allowing it to transmit shaft torque while the vehicle is operating. This system is a testing tool used by automotive and racing engineers to obtain real-time torque measurements from vehicle drivelines.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
E37 THT Vertical | Non-Threaded | Up To 3 Ncm
E37-VNxx1/4/8/9/A/B/C/D
-
Incremental encoder with dual function and without thread, 32 detent positions, switching torque up to 3 Ncm and a rotational life up to 1 Mio revolutions
-
Product
Digital Torque Meter
TS-3200A
-
The TS-3200A is greatly improved in setting and usability with large sized LCD which offers easy and clear view of good contrast. Setting conditions and measurement data can be displayed in the same screen.
-
Product
Custom & Special Models
-
Futek Advanced Sensor Technology, Inc.
Custom Load Cells manufactured in the US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Custom Force Sensors and Custom Torque Sensors utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
-
Product
E37 THT Horizontal | Non-Threaded | Up To 4.5 Ncm
E37-CNxx2/3/5/6/8/9/E/F/G
-
Incremental encoder with dual function and without thread, 16 detent positions, switching torque up to 4.5 Ncm and a rotational life up to 1 Mio revolutions
-
Product
Cam-Over Wrenches
TSC
-
TSC is an adjustable cam-over torque wrench that's ideal for maintenance and production applications where over-torque conditions are not tolerated.
-
Product
AWD Dynamometers
MD-AWD-500-AC/EC-100/250
-
The key to designing an AWD dynamometer properly is to understand the methods currently being used by manufacturers in the field of AWD drivetrain technology. A dynamometer that can accommodate various types of AWD vehicle transmissions and wheelbases without excessive complication and, more importantly, without risking damage to a client’s AWD system is paramount. Full time AWD vehicles are designed to provide maximum performance regardless of road conditions. In cases where traction is less than ideal, a vehicle may be designed to improve stability and traction at the expense of power. This means adding torque to a spinning wheel or retarding of timing. In order to properly test an AWD vehicle for peak performance, an AWD chassis dynamometer must be able to simulate ideal road-load conditions to the vehicle. This approach allows the vehicle to be evaluated under “optimum” operational conditions; whereby torque is distributed to the vehicle’s tires in the same manner that would normally occur when a vehicle has equal traction at all four drive wheels, and is therefore operating at peak efficiency. To achieve this, Mustang’s AWD-500 Series incorporates an internal drive system that synchronizes the front and back rollers to simulate a flat, dry road condition. Synchronization, or linkage, insures that the front and rear rollers are always spinning at precisely the same road speed. This process eliminates the possibility of activating a vehicle’s traction control system and also insures that a vehicle’s torque management system is operating under the assumption that the vehicle is not skidding, turning or slipping. Mustang’s AWD-500 can be operated in AWD Mode while testing two-wheel drive vehicles. This process allows the non-driven axle to be spun by the dynamometer rollers at the same speed as the driven axle, eliminating the speed differential that occurs on two-wheel drive dynamometers – problem solved.
-
Product
07R THT Horizontal | Threaded | With Shaft
07R1-xx-20/30
-
Miniatur selector with shaft, PCB mounting and up to 3.5 Ncm switching torque
-
Product
Break-Over Wrenches
-
Using break-over wrenches helps you support your quality control inspectors by empowering your workers to prevent assembly errors. Designed to accurately tighten diverse fasteners, break-over wrenches inform their operator when the right torque is reached by deflecting on their built-in hinge. As a result, you can reduce lost product or rework related to over- and under-torque conditions. Plus, their small size enables them to fit into areas with tight clearances. The end result is a boost in both productivity and project ROI. And with break-over wrenches, Mountz gives you the flexibility to switch out heads for tricky fasteners or to get more use out of your existing tools.
-
Product
General Purpose Dual Flange Reaction Torque Sensor
TRS SERIES
-
The TRS Series reaction torque sensors offer long term reliability due to non moving parts and state of the art bonded foil strain gages. The anodized aluminum TRS Series is also available as a two axis sensor, torque and thrust, on special request. Whenever possible, the best approach for precision torque measurements is via reaction torque sensing, eliminating high maintenance and high cost of slip rings, bearings, and brushes.
-
Product
Cycle-ATV Dynamometers
EC997
-
The EC997 Series, our standard eddy current motorcycle chassis dynamometer, takes motorcycle performance tuning to the next level. The EC997 Series uses the industry’s most advanced electronics and Dynamic Load Control technology, featuring precision closed-loop torque feedback – a standard feature with every EC997 dyno. Competitor’s dynos on the market allow you to apply “percent % load” but Mustang has perfected the art and science of Dynamic Load Control and proudly offer the most sophisticated Dynamic Load Control dynamometer available at any price. Our superior control technology combined with our ultra-low inertia design allows you to precisely control loading to hold the engine at each RPM. Try doing that with a heavy drive roller and insufficient control technology – you simply cannot! Mustang has delivered thousands of performance dynamometer systems over the past 35 years and has perfected the art and science of dynamic vehicle loading and dynamometer control. We include each motorcycle make and model in our database including weight and drag coefficients so you can simulate the track right on the dyno! While other dyno manufactures are still trying to catch up with our technology, Mustang continues to lead the industry and is recognized around the world as the industry’s best with regards to dynamic dynamometer controls. Mustang has built racing dynos for Harley-Davidson as well as several end of production line testing cells for Harley-Davidson, Honda, and Polaris.
-
Product
04 With Soldering Eyelets | 4 Wafers | 24 Positions
04-4xx3-00/30-xx
-
Very robust, multi wafer selector with 15° detent angle, switching torque up to 20 Ncm and a rotational life up to 25'000 cycles
-
Product
Auditor High Capacity Test Stands
-
Designed for testing tools with continuous rotating output spindles. The test stand includes a rundown fixture, bushing for side load support, reaction post or reaction paddles, transducer and torque analyzer display.
-
Product
E37 THT Horizontal | Non-Threaded | Up To 3 Ncm
E37-CNxx1/4/8/9/A/B/C/D
-
Incremental encoder with dual function and without thread, 32 detent positions, switching torque up to 3 Ncm and a rotational life up to 1 Mio revolutions
-
Product
Torque Carts
-
AIMCO offers torque carts for "lineside" or "point of use" tool validation and calibration. Our torque carts allow testing of tools on repeatable joint simulators and "in process" use on production joints, allowing users to identify process capability. There are multiple torque cart options:
-
Product
Engine Dynamometer
H3604
-
Power: 3,200 hp (2,386 kW)Torque: 18,674 lb-ft (25,329 Nm)Speed: 2,500 rpmInertia Value**: 799 lb-ft2 (33.67 kg-m2)Shipping Weight: 10,500 lb (4,763 kg)
-
Product
Electric Multipliers
EF
-
The easy-to-operate EF electric torque multipliers are designed for precision tightening and loosening of all heavy duty fastening applications. From tightening large industrial bolts used in windmill gearbox assemblies to bolting maintenance applications for oil & gas pipelines and rigs, the Mountz torque multipliers achieve precision torque in a quick, cost-efficient manner.
-
Product
Pneumatic Multipliers
CLD
-
The CLD pneumatic torque multiplier provides precision tightening and loosening of all heavy duty fastening connections. The torque multiplier shuts-off when pre-set torque is achieved. It's a non-impacting and operates at a smooth, continuous rotation, the torque multiplier increases speed and productivity, as it is faster than a hydraulic wrench and is less expensive.
-
Product
Torque Meter Bench
-
BTR is a desktop torque for torque meas urements consisting of a digital indicator model DTR and a strain gauge torque extremely rugged and compact which has a precision better than 0.20%. Ideal for the calibration and the control of torque keys and to rque screwdrivers. Microprocessor indicator is fed by 4 internal batteries with an autonomy of 200 hours, with the AUTO POWER OFF function which activates if any change in the measurement is detected in an interv al of 30 minutes. The new generation electronic section consists of a particularly long-term stable analogue circuit and of a 16 bits A/D converter which ensures 65.000 internal divisions with an acquisition sp eed of 200 conversions per second. On the display there is an analogue bar for torque, that is still active, even in the programming menu.
-
Product
Digital Torque Wrench
DIW-120/75/20/15
-
Tightening of screws and bolts and final check. The wrench head part rotates about 300 degrees! The line of sight and the display panel are always parallel, improving operability. Lightweight and compact with an integrated display! Cordless for even better operability. Stable measurement can be performed even during long hours of work. A screw tightening counter function is also included as standard. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change.
-
Product
E33 THT Vertical | Non-Threaded | Up To 4.5 Ncm
E33-VNx2/3/5/6/8/9/E/F/G
-
Encoder without thread, 16 detent positions, with or without push function, switching torque up to 4.5 Ncm and a rotational life up to 1 Mio revolutions
-
Product
Engine Dynamometer
TD-3102
-
Power: 1,250 hp (932 kW)Torque: 3,600 ft-lb (4,881 Nm)Speed: 6,000 rpmWater Use: 100 gpm @ 60 psi (6.3 lps @ 420 kpa) (No cooling system)Minimum Controllable Power: 11 hp (5 kW)Minimum Controllable Torque: 32 ft-lb (24 Nm)Inertia Value: 570 lb/in2Weight: 360 lb (163 kg)
-
Product
Torque Transducers
-
Procter & Chester Measurements Ltd
A transducer is a generic name that is a device which is usually electronic that coverts a physical attribute to a measurement signal.
