Phantom Loads
generate different current values based upon the current rating of the energy meter under test. 2) standby power of a device turned off.
See Also: Parasitic Drain
-
product
Electronic Loads
T3EL Series
The T3EL series is a family of single channel, 200 & 300 Watt Electronic Loads that are ideal for R&D, product validation and Q&A in a bench or automated environment for low to medium power applications starting from 60mA, such as electronic components, batteries, portable chargers and power products. Electronic Loads are typically used to provide a load to the outputs of a power supply, usually capable of dynamic loading, and are fully programmable. Electronic Loads help designers to test electronic power products and ensure quality, reliability, and performance.
-
product
Load Cells
Instron is the only testing system manufacturer that designs and builds its own load cells, ensuring exceptional accuracy, stiffness, and alignment across a wide measurement range. Produced at Instron’s High Wycombe, UK facility, each load cell is temperature-compensated and calibrated to international standards for outstanding repeatability. Backed by the largest commercial deadweight stack in the U.S., Instron’s calibration process delivers precision that often exceeds industry requirements—providing reliable, traceable performance for even the most demanding materials testing applications.
-
product
Load Modules
Load Modules are available with a selection of voltage and current ranges. Use for discharge testing batteries, power supplies or test gear.
-
product
Terminations & Loads
We have more than 40,000 rf & microwave coaxial terminations in stock we can ship today. We offer these Microwave & RF terminations: SMA Terminations, Type N terminations, 7/16 DIN terminations, 2.92mm terminations, 2.4mm terminations, TNC terminations, smp terminations, minismp terminations, 4.1/9.5 minidin terminations. 4.3/10 terminations, ssma terminations, ssmc terminations, and a few Reverse Polarity terminations. Power levels of 0.5-150 watts. RF / Microwave terminations are also known as dummy loads or 50 ohm dummy loads. Our 1.85mm terminations, are rated to 67ghz. We offer 1.0mm terminations good to 110Ghz.
-
product
Coaxial Loads
Loads are supplied standard with N connectors, which are recommended above 500 MHz.
-
product
Whole Body EM Phantoms
EM - PHANTOM
Schmid & Partner Engineering AG
The POsable Phantom for Electromagnetic sYstems Evaluations (POPEYE) is an anatomically correct human phantom based on a torso shell w/ head with posable arms, hands and legs. This radio frequency (RF) human has been designed to meet the requirements for test configurations for which the effects of the body on the EM performance cannot be neglected, such as operating tablet and laptop computers and other body-mounted transmitters. With a simple adjustment (one tightening screw), the arms, hands and legs can be positioned accordingly for conducting simulations of any usage or operation (standing, sitting, arms raised, talking position, etc...).
-
product
Load Testing
Load Testing, Simplified. We sort out the infrastructure, so you can spend more time testing. Tool Agnostic - We support JMeter, Gatling, Capybara and Selenium. Unfettered Testing - No limits on how you test, run as many users for as many tests, for as long as you like. Third-party Integration - Send results to Slack, Hipchat, Flowdock, or your own services using our API.
-
product
DC Electronic Load
EE15120A
The EE15120A DC Electronic Load / Works @ 0.0 Volts Input & real time I/O control attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices. The electronic load can act as a Current Regulator for charging
-
product
Load Termination
A process of ending a transmission line or cable to either dissipate energy as heat or prepare it for connection to a device.
-
product
Loading Rheostats (Resistive Load)
Supreme Instrument Laboratories
Loading Rheostat is a device specially designed to meet the requirements of Engineering Laboratories, Electrical Test Rooms and Industries. It is used for loading transformers, power generators, supply mains etc. neatly and efficiently. It can also be used advantageously for regulating current and adjusting voltage besides its application for calibrating meters and thus eliminating the need for graded rheostats.
-
product
Smart Load Manager
Nippen Electrical Instruments Co.
This is flush mounting micro controller based instrument with multilayer PCB having SMT components offering accuracy and reliability along with reduction in EMI and EMC interference. These are specially designed to simultaneously measure, display and communicate several electrical parameters. This meter is an Ideal data source for effective Energy management, SCADA, PLC, BMS etc to measure as many as 36 parameters on 23 display pages, which are true RMS. The readings are displayed on 3 line bright Red 7 segment LED, each row/ line having 4 14.2mm high LEDS.
-
-
product
Mechanical Load Tester
Solar modules and collectors, whether on roofs, in façades, or freestanding, are often exposed to high mechanical stress or load: A deep layer of snow or strong winds can greatly affect the materials and connections. Mechanical load test stands accurately test the durability of PV modules and thermal solar collectors.
-
product
Load Cells
For use in harsh environments, our Models T66 (bending beam),T85 and T85-T(shear beams)are manufactured fromstainless steel, fully welded and hermetically sealed to provide total environmental protection (IP68 and IP69K). The T85-Tmodel has a blind loading hole, ideal for use in platform scales.
-
product
Phantom Powered Measurement Microphone System
7052PH
The 7052PH Type 1.5TM phantom powered measurement microphone system offers a cost effective solution to acoustic measurements from phantom powered sources. Type 1.5TM - a superior Type 2. Frequency Response: <3 Hz to > 20kHz typ.(capsule). Sensitivity: 22 mV/Pa (-33 dBV/Pa)typ. Dynamic Range (capsule) 1% THD: <20dBA-150dBSPL (Capsule).
-
product
DC Electronic Loads
Next Generation Instrumental (Shanghai) T&C Tech. Co., Ltd.
NGI DC Electronic Loads
-
product
NO LOAD & LOAD TEST BENCH
International Biological Laboratories
These are the test benches incorporating control & measurement circuitry necessary for testing single phase as well as three phase transformers of several VA to MVA rating & voltage class of 11KV/433V,as well 33KV/11 KV, after manufacturing, repairing, reconditioning. Following tests can be done by these Test Sets.
-
product
DC Electronic Loads
Electronic Test & Power Systems
An adjustable electronic load gives the test engineer the ability to qualify designs, check production batches or service and repair electrical products. Many applications demand an adjustable electronic load. These include the burn-in of new devices along with general power supply, battery, fuel cell and generator testing.
-
product
Regenerative AC Load
61800
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
product
Save A Watt® Phantom Power Indicator
P4190
The Save A Watt® Phantom Power Indicator offers an easy way to save money by showing you how much power your electronics are using in standby mode. Whether it’s a cell phone charger using 5 watts, or a video game using up to 15 watts, this simple device will show you how much they’re using.
-
product
Thermal Load Boards
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
product
Partial Load Failure
PLF Device
The control device series “PLF” has been designed to monitor the partial and/ or total failure of the alternating current absorbed by loads driven by static switches and / or electromechanical relays.
-
product
Electronic Loads
SLM AC/DC
AMETEK Programmable Power, Inc.
From the leader in programmable power products, Sorensen introduces the SL series electronic loads which offer the best value with the most flexible platform. A wide range of loads are available from 75-1800W with both DC and AC input in benchtop, modular and standalone form factors.
-
product
AC Load Banks
30 kW Series
Mosebach Manufacturing Company
Mosebach’s 30 kW series load banks offers a continuous load at either 480 or 208 volts in a very compact, lightweight, portable design with a 1kW resolution.
-
product
RF Coaxial Load
RF Lambda’s coaxial loads are used to terminate RF signal chain to provide a good 50ohm match and dissipate any excess RF energy. They are available in a variety of power levels and offer low VSWR.
-
product
Terminations (Loads)
Loads find wide use as accessories for both broadband and narrowband measurement instruments. Keysight's family of fixed and sliding loads includes both general purpose grade loads as well as loads intended for use as calibration standards.
-
product
Load Support Unit
LSU220A
The LSU220A is a general purpose load support unit designed to act as a permanent power supply to maintain backup battery systems whilst alternative sources of power are either impractical or unavailable, such as running diesel engines during maintenance programs.
-
product
Power Load Switches
Low-resistance power load switches offer reliable overcurrent and thermal protection. They are designed for general-purpose power protection or for applications such as USB, hot-swap and power distribution. The power switches come in 1- or 2-channel versions with fixed and adjustable overcurrent limit. Some include a USB charge controller specifically designed to optimize USB host applications.
-
product
110V / 90 Amp Load
EL12-110M
For Telecom Rectifier and Power Supply testing. This particular Load has been designed to operate with Telecom 110V Rectifiers and Power Supplies with output Voltages in the range of 100V to 135V and is extremely cost effective.
-
product
Load Cells
An array of load cells, including bending beam, tension and compression link, button, low profile, through hole, S type, cannister, tension link, and single point load cells as well as load pins.
