-
Product
AC Engine Dynamometer
DA670
-
Power: 670 hp (500 kW)Torque: 2,010 lb-ft (2,725.2 Nm)Maximum Speed: 4,500 rpmConstant Torque Range: 0 - 1,800 rpmConstant Power Range: 1,800 - 3,000 rpmDecreasing Power Range: 3,000 - 4,500 rpmRotation: bi-directional
-
Product
Test Automation System for Emission Testing
STARS VETS
-
STARS VETS is a Vehicle Emission Test System application available with the STARS Automation platform for chassis, engine and powertrain dynamometers. The application provides test cycle execution, emissions equipment control, results calculation and reporting in compliance with the different legislative standards throughout the global regions. Its flexible design offers a wide range a customization, and it addresses the various requirements for R&D, COP and certification testing.
-
Product
Display-Only Dynamometer Testing Instrument
DynTek-PC
-
The DynTek-PC for engine dynamometers is a display-only system intended for basic engine dynamometer testing requirements. This system provides for the measurement of torque in either tension or compression (both clockwise and counter-clockwise engine rotation) and speed from a standard Magnetic Pickup. The system is designed to set on a table or desktop near the PC.
-
Product
Towing Dynamometer
RS-60K
-
RS-60K towing dynamometer is designed for testing Class B trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-60K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-60K is designed to maintain 60,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
Product
2WD Dynamometers
MD-500 Series
-
For those shops that wish to ease into the dynamometer performance tuning market one step at a time, Mustang offers a perfect solution. The MD-500 dyno. An excellent 2WD performance dyno in and of itself, the MD-500 is simply one-half of the MD-AWD-500 system. The MD-500’s multiple upgrade paths allow it to accept Mustang’s AWD upgrade in the future and also enable it to accept a second eddy current PAU for increased loading capability should you ever feel the need to expand your testing capabilities. With 1,500-hp measurement capacity, the MD-500 can handle high performance front wheel and rear wheel drive vehicles. If your shop caters to the motorcycle market too, the MD-500 series can be purchased with the optional motorcycle adaptor kit. The 500-SE offers a compact frame with a narrow 80-inch outer track and is great for shops with limited space that mainly focus on passenger cars and smaller pick up trucks.
-
Product
1100 HP Water Brake Chassis Dynamometer
TD-36
-
Weight Capacity: 30,000 lb (13,608 kg) per axleRoll Brakes: Pneumatically-actuated discShipping Weight: 13,200 lb (5,987 kg)Capacity: 1,100 hp at 45 mph (820 kW at 72 kph)Rolls: 36 by 31 in. (915 by 787 mm) 4 fixed rolls to accommodate axle spreads from 48 to 74 in. (1219 to 1880 mm) tandem centersPit Required Depth: 35 in. (889 mm)
-
Product
Engine Dynamometer
DE20
-
Power: 27 hp (20 kW)Torque: 59 lb-ft (80 Nm)Speed: 12,000 rpmWater Use*: 4 gpm (15.1 lpm)Inertia Value: 0.30 lb·ft2 (0.0125 kg·m2)Shipping Weight: 904 lb (410 kg)Rotation: bi-directional*No Cooling System
-
Product
Water Brake Engine Dynamometers
DH Series
-
Ideal for gasoline engines and lower-horsepower diesel engines, Taylor Dynamometer’s DH Series Water Brake Engine Dynos can operate at speeds up to 5,500 rpm. Choose from three different models with capacities ranging from 270 to 805 hp (201 to 600 kW).
-
Product
Towing Dynamometer
RS-80K
-
RS-80K towing dynamometer is designed for testing Class B trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-80K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-80K is designed to maintain 80,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acidbatteries to charge and testing is unlimited at low speeds.
-
Product
Engine Dynamometer
DE80
-
Power: 107 hp (80 kW)Torque: 118 lb-ft (160 Nm)Speed: 14,000 rpmWater Use*: 15 gpm (56.8 lpm)Inertia Value: 0.65 lb·ft2 (0.0275 kg·m2)Shipping Weight: 1,213 lb (550 kg)Rotation: bi-directional*No Cooling System
-
Product
Engine Dynamometer
H3610M
-
Power: 10,000 hp (7,457 kW)Torque: 50,000 lb-ft (67,820 Nm)Speed: 2,500 rpmInertia Value**: 1,963 lb-ft2 (82.72 kg-m2)Shipping Weight: 15,750 lb (7,144 kg)
-
Product
Micro Dyne System
-
With over 50 years' experience in dynamometer design and torque measurement, Magtrol has revolutionized the industry. Magtrol's NEW Micro Dyne, capable of measuring extremely low torques (2.0 mNm can be resolved to 0.0004 mNm), is DESIGNED EXCLUSIVELY for testing miniature and micro motors.For the utmost convenience, the Micro Dyne is packaged as a COMPLETE MOTOR TESTING SYSTEM. Everything that is needed to accurately and efficiently test miniature motors and micro motors is included with the purchase of a Magtrol Micro Dyne. The only component that needs to be supplied by the customer is a laptop or desktop personal computer and a motor power supply.
-
Product
Electric Motor Dynamometer
-
Dynamometer consists of aggressively designed rotor technology that allows for higher torque without the need for multiple rotors. Thus not only does the WB Series unit offer more pack to the punch, but the inertia of the WB Series unit stays well below the inertia of the engine being load-tested.
-
Product
Towing Dynamometer
RSL-15K
-
RSL-15K Towing Dynamometer is designed for testing today’s full-sized cars, to mid and full-sized SUVs. The unique design of the RSL-15K allows it to be used for a wide range of vehicle weights. Built with an all-aluminum frame, sheet metal body and rides on an independent, coil spring suspension. The RSL-15K uses two eddy current absorbers for power absorption. The power is provided by batteries and an alternator.
-
Product
Diesel Fleet Maintenance Chassis Dynamometer
MD-7500
-
At the heart of the MD-7500 is a set of three air-cooled eddy current power absorbers. Each absorber, or brake, can hold up to 600-hp (total power of 1,800-hp) more than enough to simulate a fully loaded transit bus. As the systems PAU''s (brakes) are air-cooled, no water is required to or from the device eliminating the high cost of water consumption and/or the cost of an expensive water recovery system which can sometimes exceed the cost of the dynamometer system itself. Mustang is the only company that offers a Universal Fleet Test Bed without water supply requirements.
-
Product
Water Brake Engine Dynamometers
H36 Series
-
Low rpm. High torque. Ultra-low inertia. And yet, it comes in a compact package that uses as little of your valuable floor space as possible.
-
Product
Emissions Dynamometers
MD-1000-M
-
The MD-1000 sets the industry standard for heavy duty chassis dynamometers due to its rugged design and accurate loading capabilities. Simulate on-highway driving conditions under real world loads. Adjust loading to simulate a host of in-use operating conditions. The 1000 is approved for use in Nevada and Colorado for Diesel Smog Testing.
-
Product
Test Automation System for Durability Testing
STARS MATS
-
STARS MATS is a Mileage Accumulation Test System application available with the STARS Automation platform for chassis dynamometer. The application provides test execution, equipment control, refueling, and vehicle state monitoring to perform long endurance test without the necessity of continuous staff presence. Its flexible design offers a wide range a customization, and it addresses the different testing requirements from manual to fully-automated operation.
-
Product
AC Engine Dynamometer
DA195
-
Power: 195 hp (145.4 kW)Torque: 682 lb-ft (924.7 Nm)Maximum Speed: 5,600 rpmConstant Torque Range: 0 - 1,500 rpmConstant Power Range: 1,500 - 2,700 rpmDecreasing Power Range: 2,700 - 5,600 rpmRotation: bi-directional
-
Product
AC Engine Dynamometer
DA50
-
Power: 50 hp (37.3 kW)Torque: 87.5 lb-ft (118.6 Nm)Maximum Speed: 8,500 rpmConstant Torque Range: 0 - 3,000 rpmConstant Power Range: 3,000 - 5,100 rpmDecreasing Power Range: 5,100 - 8,500 rpmRotation: bi-directional
-
Product
AC Engine Dynamometer
DA16HS
-
Power: 16 hp (11.9 kW)Torque: 42 lb-ft (56.9 Nm)Maximum Speed: 11,000 rpmConstant Torque Range: 0 - 2,000 rpmConstant Power Range: 2,000 - 3,200 rpmDecreasing Power Range: 3,200 - 11,000 rpmRotation: bi-directional
-
Product
Brake Test Systems
GIANT 9000 Series
-
The major test target is to detect noise and vibrations generated by the vehicles brake. Our intention was to build a dynamometer that can operate either with brakes mounted to the complete vehicle, or with just the axle module mounted to a universal adaptor system or wheel suspensions.
-
Product
Test Stand Controller for Automotive, Marine, and Aerospace Engine Testing
SPARC
-
The new SPARC Engine is the state-of-the-art test stand controller for automotive, marine and aerospace engine testing. The latest generation offers you advanced hardware and software for the highest performance, and touch functionality for intuitive operation. It is suitable for test stands with a synchronous machine (DYNASPM), asynchronous machine (DYNAS3), hydraulic dynamometer (DT) and eddy current dynamometer (WT) as well as tandem applications.
-
Product
Towing Dynamometer
RS-25K
-
RS-25K Towing Dynamometer is designed for testing today’s full-sized SUVs and light trucks. The RS-25K is built with a heavy-duty steel frame, an aerodynamic body and rides on an independent, air ride suspension using two eddy current absorbers with special high temperature coils to absorb energy. The RS-25K is powered by an industrial generator so there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
Product
Towing Dynamometer
RS-10K
-
RS-10K Towing Dynamometer is designed for testing today’s mid-sized cars and SUVs. The RS-10K is built with an all aluminum frame, an aerodynamic body and rides on an independent, air ride suspension and uses an eddy current absorber with special high temperature coils to absorb energy. The RS-8K is powered by an industrial generator, so unlike battery/alternator Towing Dynamometers, there are no lead-acid batteries to charge and testing time is unlimited at low speeds.
-
Product
Engine Dynamometer
DX34
-
Power: 1,000 hp (746 kW)Torque: 3,217 lb-ft (4,361 Nm)Speed: 4,000 rpmWater Use*: 73 gpm (276.3 lpm)Inertia Value**: 82 lb·ft2 (3.5 kg·m2)Shipping Weight: 1,846 lb (837 kg)Rotation: bi-directional
-
Product
Engine Dynamometer
H3606
-
Power: 2,000 hp (1,491 kW)Torque: 23,873 lb-ft (32,367 Nm)Speed: 2,550 rpmWater Use*: 146 gpm (552.7 lpm)Inertia Value**: 311.4 lb·ft2 (13.12 kg·m2)Shipping Weight: 3,339 lb (1,515 kg)*No Cooling System**With Companion Flange
-
Product
Engine Dynamometer
DH23
-
Power: 805 hp (615 kW)Torque: 1,275 lb-ft (1,729 Nm)Speed: 4,500 rpmWater Use*: 60 gpm (227.1 lpm)Inertia Value: 11.4 lb·ft2 (0.48 kg·m2)Shipping Weight: 475 lb (215 kg)*No Cooling System
-
Product
Towing Dynamometer
RSL-25K
-
RSL-25K Towing Dynamometer is designed for testing today’s full-sized cars, SUVs and light trucks. The RSL25K is built with a steel frame, sheet metal body and rides on an independent, coil spring suspension. The RSL-25K uses eddy current absorbers for power absorption. The power is provided by batteries and an alternator.
-
Product
550 HP Water Brake Chassis Dynamometer
CM-51S
-
AC power, air and water required at one side wallas applicable.• Room length, and pit location within length,must be determined by user to fit maximumtruck length and rear overhang.• Provide at least one man door for fire escapenear rear of room, but not in rear wall becausesomeone entering during a test could be struckby a stone flung from a tire. Provide ample fireextinguishers at each door and near driver.• “Back-on, Drive-off” installation configurationpreferred.
