Electric Field
space around an electrically charged object.
See Also: E-field, Electric Field Probes
-
Product
Electric Insulation Oil Automatic Measurement System
DAC-5016
-
DAC-5016 is an automatic test system of insulation oils according to JIS C-2101.The system automatically enables changing over samples (liquid cells) up to max 8 pieces and testing the dielectric loss tangents and the volume resistivities.In automatic mode, the dielectric loss tangents and the volume resistivities are automatically measured, and then the results are printed out with the built-in printer. And the relative permittivities and the volume resistivities calculated are also printed out. Therefore the test time is greatly saved compared to the conventional test methods.
-
Product
Antenna, High Field Biconical
EM-6913 | 20 MHz – 300 MHz
-
The Electro-Metrics EM-6913 can be used for generating high intensity fields as required for EMC immunity testing 20 MHz to 300 MHz.
-
Product
Near Field Probes
-
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
Product
Field-installation Type Electric Conductivity Meter (Two-Wire Transmission, For Low-concentration)
HE-300C
-
HE-300C connects conductivity sensor (ESH/FS Series) and measures conductivity and temperature in the sample water. It is suitable for monitoring pure water/boiler water drainage recovery control and inline measurement of pharmaceutical water conductivity according to USP<645> quality guidelines.
-
Product
Near Field Probes 1GHz - 10 GHz
SX set
-
The SX1 set consists of 3 passive near field probes for making measurements in the development phase of E-field and magnetic field with a high clock frequency in the range from 1 GHz to 10 GHz. The probe heads of the set SX allow for measurements close to electronic assemblies, e.g. on single IC pins, conducting paths, components and their connectors, to localize interference sources. Field orientation and field distribution on an electronic assembly can be detected through trained use of the near field probe. The near field probes are small and handy. They have a sheath current attenuation and are electrically shielded. They can be connected to a spectrum analyzer or an oscilloscope with a 50 Ω input. They have an internal terminating resistance.
-
Product
Electrical Testers
-
Digital voltage and continuity tester with LCD screenAC and DC voltage testing (7 thresholds) with automatic AC or DC detection, audible continuity and single-pole phase test.
-
Product
Electrical Receiver Conformance Test (OIF-CEI-56G)
M809256CA
-
OIF-CEI 4.0 Receiver Test Application for OIF-CEI 56G-Very Short Reach (VSR), Medium Reach (MR) and Long Reach (LR) PAM4.
-
Product
Electric Multipliers
EFC
-
The easy-to-operate EFCip electric torque multipliers are designed for precision tightening and loosening of all heavy duty fastening applications. From tightening large industrial bolts used in windmill gearbox assemblies to bolting maintenance applications for oil & gas pipelines and rigs, the Mountz torque multipliers achieve precision torque in a quick, cost-efficient manner.
-
Product
Field Ground Module
SEL-2664
-
Schweitzer Engineering Laboratories, Inc.
Add the SEL-2664 Field Ground Module to the SEL-300G or SEL-700G to protect all the critical components in your generator with one comprehensive relay. Or, add the SEL-2664 to the SEL-2664S to complete ground fault protection on both the rotor and stator.
-
Product
Electrical Test System TY-CHECKER
DG Series
-
Experience high-speed testing and short tact timers!
-
Product
Electrical Safety Test Equipment
-
Making a product “safe” requires an understanding of “hazards” that exist in each electrical product. Electrical shock is one of the four fundamental hazards. Because of that, it must be a part of any product electrical safety evaluation. Even though a product requires an electrical power source and uses electrical or electronic components, it should not present an electrical shock hazard to the user.Ground bond or earth continuity testing prevents electrical shock hazards. Similarly to a fault to earth, test instruments generate a high current. The standard requires that the resistance between protective earth and any conductive surface on the equipment does not exceed 0,1 Ohm. The test is performed by applying a DC current between the conductive surface and protective earth. By measuring the voltage drop, it calculates the resistance.RMO-E instruments are ideal for testing the protective bonding (grounding) of equipment following the standard IEC 61010-1. Applying current up to the value of 100 A and the ability to provide in the Contin menu (continuous operation) test current for the pre-set test duration (equal or exceeding 1 min) gives a user a possibility to easily check the protective bonding/grounding of the equipment. The full load voltage of 12 V assures proper measurement and accurate result. Finally, an instrument displays pass/fail classification according to user-preset parameters.
-
Product
CHEK 3-in-1 Electrical Tester
GT 3100GAM
-
Cable test monitors line continuity, shows completed circuits. Lamp test indicates the lamp and fixture continuity. Circuit tester checks if power is available, if polarity is correct, if wiring is correct.
-
Product
Electric Attitude Gyroscopes
5000EG-series
-
The 5000EG gyro is based on our air-driven 5000B model, whose proven reliability has made it the industry standard for many years. There are two models available: 14 and 28 VDC. The rotor is precisely machined from a heavy-metal tungsten alloy, which has a higher mass than brass, contributing to the instrument’s demonstrated stability. The electric motor is driven by a built-in power inverter, and has an integrated air-erection mechanism. A warning flag is deployed upon loss of primary power. During acrobatic flights or short stops, the gyro’s mechanism can be caged whenever the knob is pulled.
-
Product
Electricity Metering Device
Mk7C
-
Built on the advanced Atlas metering platform, the Mk7C is a single meter with an integrated 100A UC3 compliant relay which allows disconnection and reconnection of electrical services remotely.
-
Product
Electrical Safety Test Scanner
19200
-
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
Product
Multifunctional Electrical Installation Testers
Eurotest XA
-
The fifth generation of Metrel's multifunction electrical installation testers brought know-how in the testing procedures to reality. Because of the need to be efficient, faster and competitive but still responsible and concentrated on safety, all the technical content and innovations under AUTO SEQUENCE, rotate around taking care about testing procedures itself.
-
Product
Electrical And Optical Clock Recovery
Series Oscilloscopes
-
Provide clock recovery capabilities for optical and electrical NRZ and PAM-4 signals up to 64 GBaud with jitter spectrum analysis (JSA) and integrated variable equalizers advanced features
-
Product
5 kV Electric Motor Analyzer
MCE
-
The MCE is the most comprehensive static electric motor test equipment available on the market today. Through a series of powerful diagnostic tests, the MCE provides a complete look at the health of an offline motor. The MCE provides critical information to technicians allowing them to diagnose problems early, thus reducing unwanted downtime.
-
Product
Residual Magnetic Field Meter
MP-80 V2
-
The MP-80 Version 2 residual magnetic field meter offers a memory for stored measurements and a wireless interface for managing those measurements in the device or the Lima Connect app. These features make magnetic field measurements more efficient, especially when testing residual magnetism and magnetic fields in various applications.
-
Product
Wet-Mateable Multi-Channel Electrical Connectors Rated for 1/1.7 (3.3) kV and 30 A
Nautilus WM1.7-30
-
Teledyne ODI's patented Nautilus is recognized as the leading choice for high reliability wet-mateable, multi-channel electrical connectors. Over 100,000 Nautilus connectors have been delivered for projects in diverse industries including oil and gas, oceanography, and defense.
-
Product
Electrical Testing Monitoring
-
The IEC 61850 represents the migration from the analog to the digital world to the substations. Accordingly, industry faces a period of transition, also noticing the effects of IEC 61850 in the traditional checking and monitoring procedures.
-
Product
28/45 GHz Dual Optical Channel and 50 GHz Dual Electrical Channel DCA-M
N1092E
Oscilloscope
High accuracy, low cost solution for optical and electrical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, and fast sampling rates for high throughput.
-
Product
Horizontal Field of View Vehicle Camera System
ThermoVision SS
-
The SS camera is a vehicle camera system for driver's vision has a horizontal field of view (FOV) of 55 or 90 degrees. The SS system is based on an uncooled thermal camera to provide good situational awareness day and night.
-
Product
Defect Review Station Software for electrical test
Faultstation
-
Centralize all error review for your different testers in a single seat! To capture PCB layout information, FaultStation offers the choice of DPF or IPC input. In combination with a Ucamco data-prep seat, DPF is the obvious choice, while industry standard IPC provides a doorway to all other data-prep systems in today’s marketplace. Once the layout data is available, you combine it with the error information from a variety of different models and makes of testers.
-
Product
Field meters
-
Small, lightweight and low priced non frequency selective Efield meter. It can be used for relatively high field strengths e.g. to observe the field in a TEM cell or a strip line.
-
Product
EMF/ RF Field Strength Meter
-
Designed for measuring and monitoring Radio–Frequency electromagnetic field strength.
-
Product
Multifunction Electrical Installations Meter
MPI-520S
-
The MPI-520S multifunction meter is dedicated to perform diagnosis of electrical installation according to IEC 61557 standards. Digital meter MPI-520S is designed to measure impedance of a short cicuit loop also without triggering RCD, parameters of RCD, insulation resistance, earthing resistance, continuity and also for phase sequence testing. Furthermore to measure and logging of AC voltage and current, frequency and power.
-
Product
Field Ttesters
AT.One
-
The AT-One is the ultimate TDM tester T1 and E1 tester designed in 2015 and launched in 2016 for field engineers that are installing, commissioning and troubleshooting T1, E1 links, Synchonization Networks, and Datacom circuits. This instrument, designed and manufactured in Europe by ALBEDO Telecom, is a brand new platform, incorporating the latest available electronics, consequently you will enjoy top performance, high accuracy and, of course, a very competitive price.
-
-
Product
Single Position Automated Electric Fluxer
-
Single-position fully automated electric fusion machine with a typical sample throughput of 5-7 samples per hour. Ideal for preparing fused beads for XRF analysis and solutions for AA, ICP, and wet chemistry analysis. Patent PendingTypical samples include: Cement, Clinker, Ores, Slag, Refractories, Ceramics, Catalysts, Glass, Rocks, Minerals, Soils
