Reflection
-
Product
Goniophotometer Test System For Led Lamp
1680A 1680B
-
Shenzhen Chuangxin Instruments Co., Ltd.
Design according to IEC61341,the test method of central luminous intensity and beam angle for reflecting light, this instrument can be used to test the cross section luminous intensity distribution curve, central luminous intensity and effective beam angle of LED assembled luminaries and LED lens system with diameter less than 180mm.
-
Product
LUX Meter & RPM Meter
-
This instrument is a non-contact rotational speed meter.The meter measures the rotational speed in RPM(Revolutions Per Minute) and RPS (Revolu-tions PerSecond) with reflective markers stuck on the rotating objectto be measured.
-
Product
Circulators
-
To protect a power amplifier in case of bad antenna matching the use of a circulator is recommended. This item conducts the reflected power into an external terminating resistor where it is absorbed. Therefore the power amplifier is protected well because the output stage is always matched correctly.
-
Product
PXI-2797, 40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module
782357-01
-
40 GHz, 50 Ω, 6x1 (SP6T) Terminated PXI RF Multiplexer Switch Module—The PXI‑2797 offers a high-density, terminated multiplexer with dual 6x1 multiplexer banks in the same module. The internal termination of the PXI‑2797 helps prevent high-power reflections that arise from open channels on the module. It is ideal for passing high-order harmonics from PXI RF Signal Upconverter modules or routing multiple sources to PXI RF Signal Downconverter modules.
-
Product
Auto Spectroscopic Ellipsometer
PH-ASE
-
The PH-ASE spectroscopic ellipsometer measures thickness, refractive index and extinction coefficient of single films and multilayer stacks. Reflection measurements at different incident angles and transmission measurements can be carried out and combined with ellipsometric data.
-
Product
Imaging & Analysis
-
Microscopes offered by Buehler generally fall into the categories of stereo microscopes, upright microscopes, or inverted microscopes. Inverted microscopes are commonly referred to as metallurgical microscopes. Microscopes may offer episcopic (reflected light) observation, diascopic (transmitted light) observation, or both possibilities. Illumination may be delivered in bright field mode (BF) or dark field mode (DF), and several techniques such as differential interference contrast (DIC) and polarized light microscopy make use of the nature of light to reveal specific pieces of information when studying materials.
-
Product
Flatness Mirror
10773A
-
The Keysight 10773A Flatness Mirror is a 100% reflectance mirror that turns the direction of an incoming laser beam 90 degrees. The mirror, used in the 5530 Laser Calibration System, measures flatness in applications such as surface plate calibration. It can be used in place of the 10707A Beam Bender (6 mm or less beam diameter) for applications that require the larger aperture of the 10773A.
-
Product
Triple Monochromator/ Spectrograph
Omni-λTripple Series
-
Omni-λ 500 Triple Monochromator/ SpectrographThe Triple Monochromators/Spectrographs include three 500 mm focus monochromators which are with fine alignment. The first two monochromators as the dispersion subtraction are used to reduce the stray light. The third monochromator as dispersion sum configuration is used to improve the resolution. And each unit can work well as the monochromator, and the two unit can also be used as the double monochromator. The first and the second monochromator are the side entrance and double exits, the third monochromator is the double entrances and double exits, it is easy to connect the CCD and PMT, the single channel detectors. There are three import gratings in each monochromator, and the spectral range is located in deep UV region, the middle UV and visible region. Each grating reflectivity can be up to 70% in their spectral region. Mainly used in high grade Raman spectroscopy measurement, such as UV-resonance Raman spectroscopy.
-
Product
Gloss & Reflectance
-
Visual appearance can determine a person’s perception of a product. Colour and Gloss are two key parameters that are used to define a product’s overall quality. Perception is subjective, but Elcometer’s range of gloss meters, DOI meters and colour assessment equipment can quantify appearance measurement. The ability of a surface to reflect light without scattering is known as gloss. Using a gloss meter, gloss is measured by directing a constant intensity light beam at a fixed angle to the test surface and then by monitoring the amount of reflected light at the same angle. Different surfaces require different reflective angles.
-
Product
Reflectance Standards
STAN Series
-
Ocean Optics offers specular reflectance standards for measuring shiny surfaces such as machined metals and semiconductor materials and low-reflectivity surfaces such as anti-reflective coatings and thin film coatings. The STAN-SSH varies in reflectivity from 87%-98% over the 200-2500 nm wavelength range and is available in a version (STAN-SSH-NIST) calibrated to a NIST master standard. The NIST calibration data range is 250-2500 nm.
-
Product
Total Reflection X-Ray Fluorescence (TXRF) Products
-
Total Reflection X-Ray Fluorescence (TXRF) Products by Rigaku
-
Product
PIM & Return Loss Measurement
Range to Fault (RTF)
-
Range To Fault (RTF) is an exciting new technology from Kaelus that enables operators to accurately measure the location of PIM and Return Loss faults in their RF infrastructure. Reflection data together with PIM data provides an unmatched level of clarity for identifying the location of faults in the RF path.
-
Product
Radiative Transfer Numerical Model
HydroLight
-
The HydroLight radiative transfer numerical model computes radiance distributions and related quantities (irradiances, reflectances, diffuse attenuation functions, etc.) in any water body.
-
Product
Glossmeter
480
-
Quickly and accurately measure and record Gloss, % Reflectance & Haze measurements on a wide range of materials, including paint, plastic, ceramic or metal with the Elcometer 480 Glossmeter.
-
Product
Wattchman RF Station Monitor/Alarm Systems
81070 Series
-
The Coaxial Dynamics Wattchman Monitor/Alarm measures forward and reflected RF power simultaneously in 50-Ohm coaxial cables and transmission lines. It is compatible with our entire series of 7/8" through 6-1/8" Line Sections and will accept plug-in elements that range from 5 watts to 100 kW full scale from 0.45 MHz to 2300 MHz.
-
Product
Managed Hub
HUB-5595
-
The HUB-5595 is a managed hub designed to operate with the Abaco Systems 5565 family of Reflective Memory real-time network products. The Reflective Memory hub can automatically bypass ports when it detects a loss of signal or the loss of valid synchronization patterns, allowing the other nodes in the network to remain operational.
-
Product
Amplifiers
-
Alnair Laboratories Corporation
A specially designed Erbium-doped fiber amplifier which offers a superior optical amplication performance with a very high gain factor and a minimal added noise. A near quantum limited noise figure of typically 3.8dB, and a small-signal optical gain of over 50dB is achievable with input signal as low as -50 dBm reflecting the impact of the specialty fiber and composite amplifier design, making it an indispensable amplifier for weak optical signals.
-
Product
Reflective Memory
VME-5565
-
The VME-5565 Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board can be configured with either 64 Mbyte or 128 Mbyte of onboard SDRAM. The local SDRAM provides fast Read access times to stored data.
-
Product
Underground Cable Fault Locator
KM-CFPL-620 /620B
-
Kusam Electrical Industries Limited
“KUSAM-MECO” underground Cable Fault Pre-locator is an automatic Cable Fault Locator which adopts ARM, FPGA & Dot Matrix Color LCD display Technology. This tester combines both pulse reflecting technology (TDR) & (intelligent Bridge testing (Bridge) (Model-KM-CFPL-620B) for measuring the exact fault location such as broken line, cross faults, earthing, (poor insulation & poor contact of the lead covered cables as well as plastic cables. (Model-KM-CFPL-620B)).It is a microprocessor based fault locator with a user friendly menu. It is easy to operate. It tests almost all telecom & signal cables. It has an English menu which is easy to understand & use. With Megameter & Ohmmeter it enables to test insulation resistance & loop resistance. It has USB Port for uploading test data to computer
-
Product
High Voltage 50 Ω Pulse Generator
TLP-8010C
-
High Power Pulse Instruments GmbH
*Wafer and package level TLP/VF-TLP/HMM testing*Combines TLP-8010A and TLP-4010C into one system*Can be operated together with TLP-8012A5 and TLP-3011C pulse width extenders*Ultra fast 50 Ω high voltage pulse output with typical rise time 100 ps (0-40 A) and 300 ps (> 40 A)*Up to 80 kW peak output power into 50 Ω load*Built-in HMM pulse up to ±15 kV with 50 Ω configuration*High pulse output current up to ±80 A (short circuit) with minimum 6 dB reflection suppression*High speed 50 Ω trigger output for oscilloscopes (synchronous to high voltage pulse output)*6 GPIB programmable pulse rise times: 100 ps to 50 ns*8 programmable pulse widths: 1 ns to 100 ns (0-40 A), 1 built-in pulse width: 100 ns (> 40 A)*The optional pulse width extender TLP-3011C enables pulse width up to 1.6 µs in 68 GPIB programmable steps (0-40 A)*Optional external pulse width extensions from 5 ns to 500 ns (> 40…80 A) using the external pulse width extender TLP-8012A5*Built-in pulse reflection suppression*Fast measurement time, typically less than 0.2 s per pulse including one-point DC measurement between pulses*Efficient software for system control and waveform data management*The software can control automatic probers for fast measurements of complete wafers*High performance and high quality components
-
Product
Directional Couplers & Bridges
-
A complete line of coaxial single and dual port directional couplers, and bridges for isolating, separating, and combining RF and microwave signals in such applications as power monitoring, source leveling, swept transmission and reflection measurements.
-
Product
Ultrasonic Sensors
-
Leuze electronic GmbH + Co. KG
Ultrasonic sensors are used whenever optical systems reach their limits. Hence, partially and fully transparent or extremely dark objects can be detected just as easily as objects with reflecting surfaces or objects in dusty, vaporous or humid environments.
-
Product
Metallographic Microscope
-
Beijing TIME High Technology Ltd.
A specialized optical instrument used to examine the microstructure of opaque materials, such as metals and alloys, by reflecting light off the polished and often etched surface of a sample.
-
Product
Micro Spectrophotometer
USPM-RU III
-
The USPM-RU III is a reflectometer that provides highly accurate spectral reflectivity measurements of small, curved, and thin samples without interference from rear surface-reflected light. The curved surface of the lens can be measured from a minute spot as small as ø60 µm formed on the sample surface. This provides the ability to use a goniometer to examine even the curved side lenses or other optical component.
-
Product
SP2T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave's 2-way switches are available in absorptive and reflective designs from 20 MHz to 18 GHz. They are also referred to as single pole, double throw and abbreviated SPDT or SP2T. These switches have a typical VSWR performance of 1.6:1 or better and input power handling of 200 milliwatts maximum. Switching time is 100 nanoseconds, and isolation of 60 dB or greater for most models. Supply voltages are +5V and -5V, with TTL logic control voltage of 0 to 5 volts.Both absorptive and reflective SPDT switches are packaged into Pulsar Microwave's SW2 outline. Configuration is standard with SMA female connectors. Voltage is applied with wire wrap feed thru terminals. The housing serves as electrical ground, and two turret terminals are installed for wiring.
-
Product
Rotation Meters
-
Here you will find many types of rotation meter. There are different ways of measuring revolutions within the industrial sector, either optically or mechanically. The PCE-151 handheld series of rotation meter with Rotation Meter OverviewRS-232 interface can measure revolutions and velocity and store the readings onto a computer using software which comes with the device. The handheld digital rotation meter is ideal for measuring velocity and revolutions in research and maintenance. The PCE-T236 rotation meter measures velocity both by contact and non-contact and is good value for money.Non-contact measurement of velocity is done with the help of reflective tape. For a device that can be installed for measurements over a period of time, we recommend the PAX I rotation meter.
-
Product
Goniophotometer
GMS2000
-
In this goniophotometer, the tested luminaire rotates in the prescribed burning position and around the vertical axle and a reflecting mirror rotates around the horizontal axle, meanwhile, a synchronous axle will rotate toward the opposite direction synchronously. The combined motion of the luminaire and mirror permit luminous measurement at the direction of any horizontal or vertical angle without tilting the luminaire, therefore, the luminous intensity will be not variation. The photometer head located at a fixed position of the limiting photomet- ric distance in front of the reflecting mirror to gather the light in each direction.
-
Product
FiberPulse OTDR
XO1
-
FiberPulse OTDRs send pulses down fiber optic networks from one end of the fiber, displaying a trace and reporting all detected events such as splices, connectors, macrobends and fiber ends and breaks. The total fiber length is reported along with name, location, loss and reflectance of detected events. The intuitive keypad design features integrated shortcut keys designed for quickly positioning and analysing events. Another feature of this unit is the Live Optical Signal Detect Function, which tests if the fiber is live before sending the pulse, this can effectively prevent accidental damage to the OTDR and attached communication equipment.
-
Product
Diffuse Reflectance Sphere
DRS100
-
Mobile displays are used in a variety of ambient lighting environments. The evaluation of mobile displays under diffuse illumination conditions is critical to the understanding of display performance in the real world, as mobile displays are used in a wide range of ambient lighting environments. The DRS100 is purpose-made to completely characterize the diffuse reflectance properties of mobile displays, providing uniform hemispherical illumination.
-
Product
Integrating Spheres
-
Instrument Systems Optische Messtechnik GmbH
Determination of radiant power or luminous flux from light sources with the aid of integrating spheres is one of the most important procedures in photometry. Designed as a hollow sphere whose inner surface is coated with a diffusely reflecting material, the integrating sphere ensures complete integration and mixing of light radiation. This is then output on a detector port for measurement.
