-
Product
Alternator Tester
ALTALYZER Tester
-
The Altalyzer tester is used to check the correct operation of alternators equipped with electronically controlled voltage regulators. In alternators of this type, the charging voltage is not constant, but varies depending on external factors such as: engine revolutions, number of current receivers, etc. The voltage at a given moment is determined by the motor controller by sending the appropriate information to the alternator.
-
Product
PARTIAL DISCHARGE test set
pdnt02
-
International Biological Laboratories
This Test Kit is used for non-destructive means of assessing the quality of high voltage transformers, motors, cables etc., which are used in generation & distribution of electric power.
-
Product
Servo Tester
105
-
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
-
Product
Wristat Tester
WT 25-4145.26M
-
WT 25-4145.26M Wristat Tester is available to comply with D.O.D. 4145.26 specifications. The WT25-4145.26M Wristat Tester is designed to test the integrity of our WRISTAT in a fast, efficient, and simple manner. All the elements of the WRISTAT – continuity of the strap, integrity of the protective resistor, and satisfactory strap to skin contact – are easily confirmed by pressing the top cover of the WT25-4145.26M. The operator (wearer) is tested for a resistance to ground of greater than 250K ohms and less than1,200,000 ohms. The upper limit notifies you of an unacceptably high resistance value (IE possible loss of effective dissipation) and the lower limit warns of unsafe low resistance (possible risk of electric shock from surrounding motors, live wires etc.). The unit is not switchable.
-
Product
Phase Rotation Indicator
9040
-
The Fluke 9040 is effective for measuring phase rotation in all areas where three phase supplies are used to feed motors, drives and electrical systems. The Fluke 9040 is a rotary field indicator and can provide clear indication of the 3 phase via an LCD display and the phase rotation direction to determine correct connections.
-
Product
MOSFET Drivers
-
Renesas' product portfolio includes MOSFET gate drivers for 3-phase motor applications. The drivers have built-in detection/protection functions and are suitable for inverter driver applications such as EGR, HVAC and EPS. Line up the products with LDOs for MCU, 24V battery system capability, built-in current sense amplifiers, and motor angle detection function. The products support unit downsizing and high performance.
-
Product
Motor Exhaust Gas Analyzer
MEXA-1300R
-
MEXA-1300R is a motor exhaust gas analyzing system for two and four stroke engine assembly lines and has an integrated sample handling system for removal of oil and moisture. The measurement of CO, CO2, HC and O2 (optional) in exhaust gases is made simply by inserting the sample probe into the tail pipe. AFR and Lambda are also calculated from the exhaust gas concentrations.
-
Product
AC And DC Motors
-
Omega's AC and DC motors are built to deliver reliable long-term performance. With a variety of models available, we have motors for all your application's needs.
-
Product
Single-Phase Transformer Winding Resistance Meters
RMO-TD Series
-
Using the most advanced switch-mode technology available today, the RMO-TD series is ideal for winding resistance measurements of inductive objects. Transformer resistance meters and tap changer analyzers are perfect for testing:transformer windings (power transformers, distribution, autotransformers),all types of tap changers,generators,electrical motors,high-current busbar joints,cable splices,and welding joints.In addition, transformer demagnetization can also be done with all RMO-TD instruments.The RMO-TD series contains 3 models, with maximal test currents from 25 A (RMO25TD) to 60 A (RMO60TD).The three independent voltage sense channels enable testing of three windings in series. This enables measurements of winding resistance in every tap position of an on-load tap changer without discharging between the tests.All RMO-TD transformer resistance meters have a built-in tap changer control unit. It enables remote control of on-load tap changer (OLTC) directly from the device. In order to make the most out of this feature, DV-Win software is included which can be programmed to do everything automatically – running winding resistance tests and changing OLTC tap positions.The DV-Win software also enables control and observation of the test process, as well as saving and analyzing the results on a PC. It provides a test report, arranged in a selectable form as an Excel spreadsheet, PDF, Word, or ASCII format. Additionally, DV-Win measures and calculates the OLTC transition time, the ripple and the winding resistance for each tap changing operation. The software can also perform the calculations necessary for the “Heat Run” test.All results can be exported in the report format.
-
Product
Non-Contacting Multiturn
-
A rotary position sensor translates angular mechanical position to an electrical signal. Rotary position sensors are designed for applications that typically require frequent adjustment. Shaftless designs allow for different engagement mechanisms, such as a customized shaft, a motor control, a human interface adjustment or a mechanical arm position locator.
-
Product
Production Test Stands for Electric Motors
-
Electric drives such as DC and EC motors are more and more extensively deployed in the automotive industry. At the same time there is an increasing requirement for a 100% analysis of motors for fault detection and error analysis as well as statistics on quality, without increasing production cycles times. The model-based Parameter Identification method (PI method) from imc allows testing to be performed under load, yet without an “explicit” separate load machine. Instead, the motor is loaded dynamically by exploiting its own inherent inertia. This allows motor parameters such as resistance, inductivity and friction to be determined within a few seconds. A mathematical model and its parameters reflect motor behaviour in its completeness and make it possible to monitor motor production based on limit values and trend statistics. The identified parameters of the model equation can then be used to calculate derived key performance indicators of the motor characteristic curve.
-
Product
Dynamometers For EV & Traction Motors
-
MOTOMEA’s extensive catalog puts years of innovation at your fingertips. While we invite you to browse online today, we also encourage you to contact us directly to source the specific products you need.
-
Product
AC Flash Tester
THPG
-
Very Heavy Duty with high milliamp capacity for properly testing motors and windings.
-
Product
Decoders
SignalPilot
-
Electronic Solutions ULM GmbH & Co. KG
Today we would like to present to you a brand new multi-protocol accessory decoder designed for controlling signals. Due to its intelligent software it supports DCC and Motorola®. Flexible programming makes this decoder THE all-rounder amongst accessory decoders. The SignalPilot has 16 outputs for direct connection of micro lamps respectively LEDs installed in daylight signals. Due to the fact that the outputs are designed as push/pull power amplifiers, they are suitable for both – conventional daylight signals with common anode as well as for daylight signals and/or lighting strips with common ground (common cathode), as is the case with some Viessmann® signals. Of course, the SignalPilot decoder can also handle semaphore signals and turnout motors.
-
Product
Through Hole type DC Current Sensor／for Load Current Measurements
MOHT-600B Open loop method
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Hall effect measurement for DC/AC/Pulsed current.*For the use of UPS, batteries, switching power supply, DC motor drivers, etc.
-
Product
Manual Disconnect Switches
-
Omega is the place for heavy duty manual disconnect switches. NEMA 4X washdown duty disconnect switches, rotary disconnect switches, fused switches, motor protectors and more.
-
Product
Linear Positioning
KAOS OEM
-
A speedy, slim positioning stage for two-axis applicationsBased on cog-free linear motors, KAOS two-axis positioning stages combine a differential-motion carriage and a primary carriage on a single rail. This patented design results in a fast, compact stage well suited to semiconductor, electronics assembly and pick-and-place applications.
-
Product
10 A portable digital micro-ohmmeter
MPK-253
-
The MPK-253 digital very low resistance ohmmeter is a portable, microprocessor-controlled instrument used to accurately measure resistances of switches and circuit breaker contacts, transformer and motor windings, wire and cable samples, joints in busbars, etc., using test currents from 1mA up to 10 A.
-
Product
Double Voltage Double Frequency Generator Setup
DVDF
-
This test setup is generally used to perform induced voltage test on the transformers. This set up consists of the USED motor and generator combination to develop the required voltage and frequency. Both generating unit and the drive motor are mounted on a common metallic frame.
-
Product
NI-9478 , 50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module
779940-02
Digital Module
50 V, 16-Channel (Sinking Output), 50 µs C Series Digital Module - The NI‑9478 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. The NI‑9478 features programmable current limits, which provide … customizable system protection that is ideal for solenoid and valve control applications. Each channel is compatible with signals from 5 V to 50 V and features isolation from channel‑to‑earth ground.
-
Product
Auto Transformers
-
Variac Auto Transformers are continuously variable voltage auto transformer, having a movable carbon tip, fixed to a brush-arm sliding on a silver plated commutator. Rotation of the brush-arm by either manual or motor drive, delivers-an output voltage from zero to or above line voltage.
-
Product
RH850 Family (Automotive Only)
RH850/C1x
-
The RH850/C1x microcontrollers have Resolver/Digital (RDC), Enhanced Motor Control (EMU) unit making this product suitable for motor control for Hybrid Electric Vehicles (HEV) and Electric Vehicles (EV).
-
Product
General Purpose Reaction Dual Shaft Torque Sensor
STS SERIES
-
The STS Series is our general purpose reaction type shaft torque sensor. They are often installed between devices such as motors, switches, shafts or axles, and their mounting plate to provide bi-directional torque output. They are available in six capacity ranges from 600 in-lb through 12,000 in-lb, and are made from 17-4ph heat treated stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial environments.
-
Product
High Temperature Charge Mode Accelerometers
-
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
Product
AC drives, Soft-Starters or Servo Drives Simulation Software
-
Product simulation software enables users to operate, program and simulate AC drives, Soft-Starters or Servo Drives directly from their computer without having the actual product present or connected. Our simulation software can be used as a demonstration tool during a sales meeting or as an interactive tool for training classes. Software available In addition we offer simulation software for dedicated markets such as pumping, mining, material handling, etc... to demonstrate the use of motor controls in simulated applications.
-
Product
Rocket Motor Initiators
-
Our patented Rocket Motor Initiators and Through Bulkhead Initiators are designed to work with single- and multiple-pulse rockets, as well as those platforms that might not currently have MIL-STD-1901A-compliant initiators. Excelitas initiators are designed to work in conjunction with our Ignition Safety Devices and low-energy, low-profile Blue Chip® Detonators to provide a comprehensive and reliable rocket ignition and firing solution.
-
Product
Actuator
MC-G/S.10
-
Actuator for precise operation of accelerator handle of motor cycles and 3-wheeler.
-
Product
Isolation Amplifier Digital Output
-
This coupler is an optically coupled isolation amplifier that uses an IC with a high-accuracy sigma-delta A/D converter and a GaAIAs light-emitting diode with high-speed response and high luminance efficiency on the input side, and an IC with a digital signal (MDAT, MCLK) output function on the output side. This coupler is designed specifically for high common mode transient immunity (CMTI) and high linearity (nonlinearity) applications, making it ideal for current sensing in motor drives.
-
Product
Analog Signal Generator
ASG
-
The pocket size model ASG Analog Signal Generator is an ideal tool for troubleshooting transmitters, transducers, motors and actuators. The unit generates a 0 to 10 VDC signal in increments of 1 volt or a 4 to 20 mA signal in increments of 2 mA. An LED bar graph visually indicates analog signal level. The model ASG will also continuously ramp to user defined maximum and minimum values with user defined ramp interval timing. Units are furnished with 6 ft (1.8 m) leads with alligator clips, 120 VAC plug-in adapter, protective carrying case and instruction manual.
-
Product
Camera Barrel Test System
BK8612
-
We designed the BK8612 2 Channel Noise Test System to provide noise and vibration testing for your digital camera barrel DC Motors. Because it is based on the BaKo BK2120B DAQ, it is capable of monitoring a microphone and an accelerometer concurrently to obtain data from the motor. Because you can change the parameters of functions and limits, it is versatile but still quick and easy to set up. In addition, you can look at data in real time and also store it for future analysis. Easy to use and set up, fast and accurate; if you need to maintain the quality of your camera barrel motors, this is the tester you want.
