Ground
See Also: Earth, Soil, Ground Penetrating Radars
-
Product
3U 1-Slot OpenVPX P&G, Aperture E, VITA
101V301P02-9X12R
-
3U 1-Slot OpenVPX Power & Ground, Aperture E, Supports VITA 66.4/67.3A/67.1 in J2A+B, Pass through, w/ROHS, Max data rate (Gbps) 10.
-
Product
Differential Probe
DP-16V
-
*MAX. Input Voltage: ±8KV DC or 16KV p-p or AC 5.6KV rms*Bandwidth: DC-50MHz*Input Impedance 30MΩ// 1.5PF*x20, x200, x2000 Attenuator*To Ground MAX. Voltage: 8KV CAT III*Output Impedance 50Ω
-
Product
15W to 60W - Single Output
KMS-A Series
-
*Medical Safety Cert (4kVAC In-Out)*Class II (No ground needed)*Wide Temperature Range*Low off-load power draw*High Efficiency*Small size and lightweight
-
-
Product
Eurocard Plugbord
E160-6U-1
-
VECTOR Electronics and Technology, Inc.
6U x 160mm Eurocard size for 96-pin DIN connectors. Pad-Per-Hole both sides. Voltage and ground buses around board perimeter on both sides.Pad and bus surfaces solder coated for user convenience. For solder, Wire-Wrap or mixed wiring methods.Row and column legends provided.
-
Product
Digital And Analog Call Simulation
-
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
Product
VME Test Extender 6U/400mm J1/J2
111EXT6140-012X
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Coupled Cavity TWTs
-
Communications & Power Industries
• Frequencies from 2.7 to 37.5 GHz• Peak levels: 500 W to 180 kW• Cooling type: air, liquid, conduction• Depressed or grounded collectors• CW (Continuous Wave) and Pulsed
-
Product
Surface Form Analysis System
Tropel® FlatMaster®
-
Tropel® FlatMaster® Surface Form Analysis System Fast and Precise Measurements of Ground, Lapped, Honed, Polished and Super-finished Components. The Tropel® FlatMaster® offers industry leading performance for surface form measurements to precision component manufacturers. Our non-contact optical technique analyzes the entire surface of the part in seconds, regardless of its size or complexity. The FlatMaster provides five nanometer resolution and a standard accuracy of 50 nm (2.0 μ). It rapidly and accurately measures flatness, line profile, radius and other surface parameters on a variety of materials and surface finishes.
-
Product
E-Z Check® Plus GFCI Circuit Tester
61-051
-
*Tests for correct wiring, open ground, reverse polarity, open hot, open neutral, hot on neutral, hot and ground reversed with open hot in 3 wire, 120 VAC circuits*Simulates ground fault for testing GFCI*No-slip ergonomic design maximizes comfort*Premium neon lamps prevent false readings*Tough, impact-resistant case*2-year warranty
-
Product
sbRIO-9375, Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module
781212-01
Digital Module
Non-Enclosed, 24 V, 32-Channel (Sinking Input, Sourcing Output), 7 µs (Input)/500 µs (Output) C Series Digital Module - The sbRIO‑9375 is a digital I/O interface that works with industrial logic levels and signals for direct connection to a wide array of industrial switches, transducers, and other devices. Each digital input line is compatible with 24 V logic levels, and all the output lines are compatible with 6 V to 30 V signals, based on the external power supply. The sbRIO‑9375 offers isolation between the input and output banks from channel‑to‑earth ground. Non-enclosed modules are designed for OEM applications.
-
Product
3U VPX 1 Slot Power & Ground 25G Pass Through
101VPX301P-9X13
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
Industrial Accelerometers
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
These piezoelectric vibration transducers have been designed for application under rough environmental conditions. They are dust and water protected. Their mounting base is insulated to avoid ground loops which may cause errors, particularly, close to big machinery.
-
Product
P104 Synchro/Resolver Simulation Board
73DS2
Simulator
NAI’s 73DS2 is a PC104-compatible Synchro/Resolver Simulation Board with three isolated channels. These channels can incorporate up to three Digital-to-Synchro/Resolver Converters with 1.2 VA drive capability in a stack-through module. With galvanic isolation, one of the outputs can be grounded without affecting performance.
-
Product
32Ch Isolated Input Card
SET-1310
-
This card provides 32 optically isolated digital inputs. SET-1310 combines high-density IO with high isolation voltages and a wide input voltage range. It allows to break ground loops and protect your system from high-voltage spikes, but also to connect high voltage signals to standard logic level acquisition devices. The channel-to-channel isolation allows to connect signals from different DUTs to a single acquisition system without compromises.
-
Product
LAN Network Testers
-
A cable detector can locate open power cables, either live or without current, up to 300 V. A cable detector can locate cables, circuits, short circuits and ground wires. To perform these functions, it is not always necessary to disconnect electrically sensitive devices or to disconnect the power to the cable being tested.Many cable detector devices can also locate ferrous and non-ferrous metals, wood and plastic with high degrees of accuracy. A cable detector provides a safe way to test wall sockets for which no electrical plans or wiring information is available about the cables or their output. A cable detector is very versatile, as it ensures speed and safety when making holes in walls, ceilings and floors.
-
Product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
785189-01
Temperature Input Module
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
Product
Digital Stik Liquid Level Sensor
7250
-
The 7250 Series digital stiks take field proven magnetostrictive sensing technology and packages it for greater reliability and easier installation. This liquid level sensor is ideal for liquid level monitoring, interface level and leak detection in a variety of liquid media in above ground and underground storage tanks. It was designed to meet EPA Leak Detection and API Inventory Monitoring requirements and has been approved for use in hazardous environments.The 7250 Series is series has an inherently lower cost design which results in savings. It provides the same performance and reliability as sensors that consume more power.
-
Product
NI-9264, 25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module
780927-02
Voltage Output Module
25 kS/s/ch Simultaneous, ±10 V, 16-Channel C Series Voltage Output Module - The NI‑9264 is a simultaneously updating analog output module that accommodates higher‑channel‑count systems. Higher density modules conserve chassis space, which leaves room for other measurement types. Each channel has its own digital‑to‑analog converter. The spring-terminal version of the NI‑9264 uses a 36‑position connector for the output channels, and each channel has a ground connection.
-
Product
Mobile Testing Center
MTC-1500
-
The Mobile Testing Center (MTC) is a preassembled, above ground, mobile, testing solution designed for outdoor testing applications. An affordable option to permanent Test Cells, the MTC is comprised of 2 ISO containers. Container 1 includes a Test Cell and heated and air-conditioned Control Room. Container 2 is optional and includes facility support equipment: Bulk Fuel Storage, Pneumatic System, Water Recirculation System (WRS), etc.
-
Product
Getac Tablet
F110
-
The award-winning F110 is a true revolution in rugged tablet computing. The F110 combines class-leading performance, industry-leading security, a large 11.6” widescreen display and a thin and light design that redefines rugged mobility. Designed to be about the size of a typical piece of paper, the new F110 rugged tablet breaks new ground with its large 11.6” display, cutting-edge Intel® Core™ processor, amazing graphics and dual batteries. Instead of one single removable battery, we built the F110 to have two hot-swappable batteries for potentially infinite, uninterrupted battery life.
-
Product
Universal Multichannel System up to 500V
-
- From 12 to 48 independently controllable High Voltage channels- 0 ÷ 500 V output voltage (0 ÷ 250 V, A1519B and A1619 only)- Maximum Current 0.5, 1, 10 mA or 1 mA/100 μA (dual range boards)- Individual Enable (A151x only)- Either DB37, DB25, Radiall Multipin or SHV connectors- Available with either positive, negative or mixed polarity- Up to 20 nA, 100 pA current set / monitor resolution- Up to 10 mV / 1 mV voltage set / monitor resolution- Very Low ripple, down to < 5 mVpp- 3 different channel grounding - Common Ground (AGxxxx) - Common Floating Return (Axxxx) - Full Floating (A151x, A1612, A1619)- Independently programmable for each channel: - Output voltage - Current limit - Ramp up/down - TRIP parameter- Current generator operation in overcurrent condition- Specific design for double side silicon detector (A151x)
-
Product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
-
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
Product
Ground Resistance Inspection Box
-
AllWin Instrument Science and Technology Co., Ltd.
Check the ground resistance tester each time prior to start work everyday morning and do some relevant records.
-
Product
Charge Coupled Device (CCD) Image Sensors for Space and Ground-Based Astronomy
-
(CCDs) for Space science, Ground-based Astronomy, and Earth observation applications with an impressive record of successful deliveries to a wide range of customers over 40 years.All Teledyne e2v devices can be supplied partially or fully customised to fit the application and achieve the best possible system performance. CCD image sensor design, manufacture, test and characterisation are carried out in-house enabling control from start to finish. Multi-polysilicon, multi-metal and back-illumination options are available for high resolution, high sensitivity and very low noise.
-
Product
Automated Test Equipment
-
ATE leveraging best-in-class features of Duotech's ARTES product, in addition to a rigorous environmental test bed. From the ground up, we custom-tailored a test bed.
-
Product
3U VPX 1 Slot Power & Ground
101V301P03-9003R
-
Power for 3.3V, 5V and 12V are included, rear connectors are all fully loaded, use with Elma’s slot to slot or slot to I/O bulkhead cable products during system development.
-
Product
6 Channel 6 kV/300 µA VME HV Power Supply
V6521
-
The V6521 is a 1-unit wide VME 6U module housing 6 High Voltage Power Supply Channels 6kV, 300µA. The board is available with either positive or negative output polarity; mixed version with 3 positive and 3 negative channels is also available. The channels share a common floating return, which allows on-detector grounding reducing the noise level. HV outputs are delivered through SHV connectors.
-
Product
Long Spring Ground for ZD Differential Probe Qty 2
PACC-ZD003
-
Long spring ground for ZD differential probe Qty 2
-
Product
Resistivity Meters
-
Periodic compliance checks of ESD work surfaces are super important. Monitors only verify the ground plane, or path to ground. The surface itself can wear down, become dirty, or if you use low quality mat—just not hold up. A handheld Surface Meter is great for running monthly, or prescriptive compliance verification of your ESD surfaces.
